Nortel Meridian Meridian 1 User manual

Circuit Card Installation and Testing
Meridian 1
Circuit Card Installation and Testing
Document Number: 553-3001-211
Document Release: Standard 17.00
Date: April 2000
Year Publish FCC TM
Copyright © 1993–2000 Nortel Networks
All Rights Reserved
Printed in Canada
Information is subject to change without notice. Nortel Networks reserves the right to make changes in design
or components as progress in engineering and manufacturing may warrant. This equipment has been tested
and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules, and the
radio interference regulations of Industry Canada. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense.
SL-1 and Meridian 1 are trademarks of Nortel Networks.

Page 3 of 74
Circuit Card Installation and Testing
4
Revision history
April 2000 Standard 17.00. This is a global document and is up-issued for content
changes for X11 Release 25.0x.
April 2000 Standard 16.00. This is a global document and is up-issued for X11 Release
25.0x. Document changes include removal of: redundant content; references
to equipment types except Options 11C, 51C, 61C, and 81C; and references
to previous software releases.
October 1997 Standard, release 15.00. Changes are noted by revision bars in the margins.
August 1996 Standard, release 14.00. This document is reissued to include further product
updates. Changes to technical content are noted by revision bars in the
margins.
August 1996 Standard, release 13.00. This document is reissued to include updates to
product information. Changes to technical content are noted by revision bars
in the margins.
December 1995 Standard, release 12.00. This document is reissued to include information on
the NT9D19 Call Processor Card. Changes to technical content are noted by
revision bars in the margins.

Page 4 of 74
553-3001-211 Standard 17.00 April 2000
July 1995 Standard, release 11.00. This document is reissued to include international
information to create a global NTP, Meridian 1 option 81C, and minor text
edits. Changes to technical content are noted by revision bars in the margins.
December 1994 Standard, release 10.00. Reissued for technical content.
December 1994 Standard, release 9.00. This document is reissued to include information on
the Small systems Multi-Disk Unit (SMDU), Meridian 1 option 51C, and
corrections to switch settings. Changes to technical content are noted by
revision bars in the margins.
April 1994 Standard, release 8.00. This document is reissued to include technical
information on Meridian 1 option 61C and corrections specified in the
Product Bulletin 93062 Rev. 1. Changes to technical content are noted by
revision bars in the margins.
August 1993 Standard, release 7.00. Changes to technical content are noted by revision
bars in the margins.
April 1993 Standard, release 6.00. Changes to technical content are noted by revision
bars in the margins.
December 1990 Standard, release 3.00. Updated to include the NT6D42 Ringing Generator,
QPC442 Tone Detector option settings and a correction to the QPC441
3-Port Extender.
July 1990 Standard, release 2.00.
January 1990 Standard, release 1.00.

Page 5 of 74
Circuit Card Installation and Testing
6
Contents
About this document . . . . . . . . . . . . . . . . . . . . . . . 7
Circuit card installation . . . . . . . . . . . . . . . . . . . . . 9
Acceptance tests . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Option settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Page 6 of 74 Contents
553-3001-211 Standard 17.00 April 2000

Page 7 of 74
Circuit Card Installation and Testing
8
About this document
This document is a global document. Contact your system supplier or your
Nortel Networks representative to verify that the hardware and software
described is supported in your area.
This document provides the following:
• a list of compatible slots for circuit cards used in options 51C, 61C,
and 81C
• a general procedure for initially installing a circuit card
• acceptance tests for circuit cards that provide service functions, network
control, and line and trunk connections
• option settings for the PBX circuit cards currently supported by Nortel
Networks.
Note: For informationon equipment used withsystem option 11, see the
appropriate documentation for that product.
• sample option settings for system configurations with NT8D22 System
Monitors
For detailed procedures for removing a specific circuit card and installing a
replacement, see Hardware Replacement (553-3001-520).
For option settingson telephones, attendant consoles, or add-on modules, see
the appropriate document for that equipment.
For a description of all administration programs and maintenance programs,
see the X11 Administration (553-3001-311). For information about system
messages, see the X11 System Messages Guide (553-3001-411).

Page 8 of 74 About this document
553-3001-211 Standard 17.00 April 2000

Page 9 of 74
Circuit Card Installation and Testing
18
Circuit card installation
Content list The following are the topics in this section:
•Reference list 9
•Card slots—System options 51C, 61C and 81C 9
•Circuit Card Installation 10
•Installing a circuit card 15
Reference list
The following are the references in this section:
• “Option settings” on page 31
•X11 Administration (553-3001-311)
Card slots—System options 51C, 61C and 81C
The following table in this chapter identifies card slot compatibility in the
following modules:
• NT5D21 Core/Network Module
required for options 51C, 61C, and 81C
• NT6D60 Core/Network Module
required for the option 81 only
• NT8D35 Network Module
required for options 81C, optional for option 61C
• NT8D37 Intelligent Peripheral Equipment (IPE) Module
required for option 81C

Page 10 of 74 Circuit card installation
553-3001-211 Standard 17.00 April 2000
Circuit Card Installation
Table 1
System Options 51C, 61C, and 81C card slots (Part 1 of 4)
Component Options 51C, 61C, and 81C
NT1P61 Fibre Superloop Network card Core/Net: 0–7
NT1P62 Fibre Peripheral Controller card IPE: “Contr”
NT1R52 Remote Carrier Interface IPE: “Contr”
NT1R20 Off-Premise Station IPE: any slot but “Contr”
NT4D18 Hybrid Bus Terminator Core/Net: between 11 and 12
NT4D19 and NT423 Hybrid Bus Terminator Core/Net: between 0 and 1
NT4D20 and NT422 Hybrid Bus Terminator Core/Net: between 1 and 2
NT5D11 and
NT5D14 Line side T1 Line Card IPE: any slot but “Contr”
NT5D12AA Dual DTI/PRI Card Core/Net: 0–7
NT5D61 Input/Output Disk Unit with CD-ROM
(IODU/C) Core/Net: 17, 18 and 19
NT5K02 Analog Line Card IPE: any slot but “Contr”
NT5K07 Universal Trunk Card IPE: any slot but “Contr”
NT5K09 Quad Density Digitone Receiver EEPE Slot 2 of section A or B at rear of module
NT5K10 Dual Loop Buffer EEPE
NT5K17 Direct Dial Inward Trunk Card IPE: any slot but “Contr”
NT5K18 Central Office Trunk Card IPE: any slot but “Contr”
NT5K19 E&M Trunk Card IPE: any slot but “Contr”
NT5K35 D-channel Handler Interface Core/Net: 0-7
Net: 5-12
NT5K36 Direct Inward/Direct Outward Dial Trunk
Card IPE: any slot but “Contr”
NT5K70 Central Office Trunk Card IPE: any slot but “Contr”
NT5K71 Central Office Trunk Card IPE: any slot but “Contr”
NT5K72 E&M Trunk Card IPE: any slot but “Contr”
NT5K82 Central Office Trunk Card IPE: any slot but “Contr”