NRS Healthcare N71986 User manual

1
3.0 Unpacking
Carefully unpack the product. Check all parts
are present (see Contents List). Check for
damage. If you see, or suspect a fault, do not
assemble or use the product. Contact your
supplier immediately.
1.0 Intended Use
The 2 in 1 Contour Bed Rail provides stable support to assist clients getting into, and out of, bed.
When in bed, the Bed Rail can be used to assist raising to a sitting position or repositioning when
lying.
Designed for use with divan beds (except sprung divan base), most slatted domestic beds, and is
suitable for all bed sizes from single to king-size. It can also be fitted to super king-size beds with
additional straps (see back page for details). Not suitable for profiling beds.
User Instrucons
N71986 - 2 in 1 Contour Bed Rail
ITEM CONTENTS QTY
1E-Clip 2
2Bed Rail Board 1
3Contour Hand rail 1
4Bed Straps 2
Important General Safety Warning
Please ensure these instructions are fully read and
implemented. Failure to do so may result in injury.
Retain these instructions in a safe place for future
reference.
Maximum
User Weight
25st
160kg
2.0 Safety
2.1 WARNING To avoid possible head entrapment,
position the Bed Rail at least 320mm (12.5”) away from
both headboard and footboard. See diagram.
2.2 ALWAYS ensure that the mattress is as close as
possible to the Bed Rail. Any gap could allow the client
to become wedged in-between.
2.3 DO NOT exceed product Maximum User weight:
160kg (25st)
2.4 Always use the Securing Straps provided when
fitting to a divan bed.
2.5 Regularly check the straps are tight and the device
is stable and firmly fitted.
2.6 Not suitable for use by children.
2.7 Do not fit this product to profiling beds or sprung divan beds. NRS Healthcare have a range
of products for these applications, please refer to our website, or contact our helpline.
320mm (12.5”)
Minimum

2
4.0 Installation Instructions - Slatted Bed with
fixed slats:
4.1 Remove the mattress and place the Bed Rail
Board inside the wooden bed frame. Ensure that the
Hand Rail Guide is positioned upwards (see
Diag.1).
4.2 Place the Contour Hand Rail into the Hand Rail
Guide. Secure in position with the two e-clips (see
Diag.1).
4.3 Position the Bed Rail such that the user can
reach the handle from a relaxed lying position
without having to stretch. For the safety of the user,
this must be at least 320mm away from the
headboard or footboard.
Secure the Bed Rail to the bed with the straps
provided:
4.4 Thread one end of the strap (with female buckle)
from under the bed up around the bed slat, through
the triangular slot on side “A” of the Bed Rail Board
and back under the bed past the slat (see Diag.2).
4.5 Repeat step 4.4 using the other end of the strap
(with male buckle) through the opposite triangular
slot on side “B” of the Bed Rail board (see Diag.3).
4.6 Pull both buckles so they meet in the middle on
the underside of the bed and clip together (see
Diag. 4). Pull the loose end of the strap to tighten.
Tuck away any loose strap ends to prevent tripping.
4.7 Repeat the procedure for the second strap at
the bottom of the Bed Rail Board (see Diag.3).
4.8 Replace the mattress. Check the rail is stable
and secure before use.
5.0 Installation Instructions - Slatted Bed with
loose slats:
For beds where the slats are not individually
secured to the bed frame, do not use the fixing
straps.
5.1 Assemble the Bed Rail as shown in Diagram 1
above.
5.2 To provide additional security, we recommend
placing a non-slip mat between the Bed Rail and the
slats (see back page for details).
5.3 Replace the mattress. Check that the Bed Rail is
stable and secure before use.
Diagram. 1
Contour
Hand Rail
Bed Rail
Board Hand Rail
Guide
E-clip x2
Diagram. 2
Diagram. 3
Side “A”
Side “B”
1st Strap
Position
2nd Strap
Position
Diagram. 4
Clip together and
tighten both straps

3
6.0 Installation Instructions – Divan Bed
6.1 Remove the mattress and place the Bed Rail Board
onto the divan base in the desired position. Ensure that
the Hand Rail Guide is positioned downwards over the
edge of the divan (see Diag.5).
6.2 Place the Contour Hand Rail into the Hand Rail
Guide. Secure in position with the two e-clips.
6.3 Position the Bed Rail such that the user can reach
the handle from a relaxed lying position without having
to stretch. For the safety of the user, this must be at
least 320mm away from the headboard or footboard.
To secure the Bed Rail to the divan bed with the straps
provided:
6.4 Take the first strap. Place the female buckle through
one of the triangular slots near the Contour Hand Rail
(A) and tie a secure knot. The buckle should hang down
the side of the bed around 50-75mm (2-3 inches) (see
Diag.6).
6.5 Feed the strap under the bed-rail board and up
through the rear triangular slot (B), loop it round the end
of the bed board and back through the slot (B) (see
Diag.6). The strap should be tight under the bed-rail
board and the bed-rail board should not slide on the
strap.
6.6 Feed the strap over the top of the bed and back
underneath the base (see Diag.7). To fit the strap under
the divan base, take the strap to the end of the divan
base, lift up the end of the divan base and feed the
strap underneath the legs / castors.
6.7 Once the strap is underneath the divan base, bring
the male buckle up the side of the bed to meet the
female buckle hanging down.
6.8 Clip the two ends of the strap together.
6.9 Pull down on the loose end of the strap to tighten.
The Bed Rail Base should be tight against the divan
base. Tuck the loose end of the straps under the bed to
prevent tripping.
6.10 Repeat for the second strap, fitting to the other
side of the Bed Rail Board. The Bed Rail should now be
fully secured to the divan base (see Diag.7).
6.11 Replace the mattress. Check the Bed Rail is stable
and secure before use.
Diagram. 7
Diagram. 5
Bed Rail Board
Hand Rail
Guide
Diagram. 6
Slot “B”
Slot “A”
Knot Strap

4
7.0 Changing the Bedding
If required, the Contour Hand Rail may be removed from the Bed Rail Base when changing the
bedding. Simply remove the two e-clips and remove the Contour Hand Rail. To replace, re-fit and
replace the e-clips (see section 4.2 or 6.2).
8.0 Cleaning
8.1 Wipe product clean with a soft cloth, moistened with warm soapy water. Ensure product is
rinsed and dried fully before storage or re-fitting.
8.2 A dilute bleach solution may be used for disinfection on the Bed Rail Base and Contour Hand
Rail but not the straps.
8.3 Caution: Do not use abrasive cleaners or cloths to clean or dry any surfaces.
9.0 Maintenance
9.1 Check regularly for signs of wear or damage.
9.2 Remove from use immediately if there are any signs of wear and damage or if the Contour
Hand Rail is excessively loose in the Bed Rail Base.
9.3 Check that all fixing straps are tight and the Bed Rail is correctly positioned.
9.4 Check there is no gap between the Contour Hand Rail and the mattress.
9.5 Check both E-clips are fitted correctly and are secure.
10.0 Spare Parts & Accessories
 L75930 - 2 in 1 Bedrail Strap
 M84780 - Slip Resistant Netting (white)
11.0 Product Disposal
Product should be thoroughly cleaned prior to disposal.
Product is manufactured from metal and plastic and can be disposed of through Local Authority
Household Waste and Recycling Centres or through Local Trade Waste Collectors.
12.0 Product Guarantee
NRS Healthcare guarantee this product for a period of 12 months, from the date of purchase,
against faulty materials and workmanship. This guarantee does not cover abuse, misuse,
interference or tampering with any part of the product.
Any guarantee issued by NRS Healthcare does not affect your statutory rights.
NRS HEALTHCARE
Sherwood House, Cartwright Way,
Forest Business Park, Bardon Hill,
Coalville, Leicestershire,
LE67 1UB UK
NRS Healthcare is a Leading Supplier of Community Equipment and Daily
Living Aids, to view our full range, visit our website:
UI/N71986/11/17/Iss2
www.nrshealthcare.co.uk