Nucraft Merino Series User manual

Merino Installation Instructions
ID:

Before Beginning Installation
•Read through the entire instruction thoroughly
•A minimum of 2 persons is required for this assembly
•These instructions reflect typical assemblies. They may not match your specific configuration.

Required Tools and Hardware
•Drill Driver
•#2-#3 Phillips Bit
•#2 Square Bit
•3/8” Nut Driver
•Laser Level
•5/16” Wrench
Hardware 1
Hardware 2
Hardware 3
Hardware 4
Hardware 5

Merino Freestanding

Merino Freestanding Exploded
1. Freestanding Desk
2. Work Surface
3. Lateral File Pedestal
4. Box Box File Pedestal
5. Tack Board
6. Overhead
7. Tower
1
2
3
4
5
6
7

Merino U-Shape

Merino U-Shape Exploded
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box Box File Pedestal
5. Tack Board
6. Overhead
7. Tower Access Panel
8. Corner Support
9. Bridge
5
9
8
4
6
10 23
7
1

Merino L-Shape

Merino L-Shape Exploded
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box Box File Pedestal
5. Tack Board
6. Overhead
7. Overhead Hood
8. Corner Support
9. Power Option
7
1
5
4
32
9
8
6

Merino T-Shape

Merino T-Shape Exploded
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box Box File Pedestal Support
5. Tack Board
6. Overhead
7. Overhead Hood
8. Access Panel
9. Tower
9
7
6
35
8
4
2
1

Step 1: Installing the Credenza
•Locate the pedestals and set in place with a level.
•Align work surface with mitered edge on pedestals. Attach using hardware #3 and #5.
•If station has additional work surfaces, attach the same way. Then connect using mending plates and
screws (hardware #4).

Step 2: Attaching Corner Support
•Install connector pins (hardware #1) to the work surface.
•Lower the work surface onto the corner support, aligning the pins with the corresponding holes in
the corner support.
•Secure by turning clockwise by a half turn.

Step 3: Installing Stanchions
•(If wall hung, skip to Step 5.)
•Loosen the stanchion channel bolts. DO NOT
remove.
•Slide the stanchions in the channels. Adjust
glides on the stanchions until scribe line is
flush with work surface.
•Tighten the stanchion channel bolts.
•Attach cross members using 3/8” bolts.
Stanchion Channel
Bolts
Cross Member
Locations

Step 4: Installing Tack Board and Overhead
•Attach the tack board using the pre-installed Z-clips on the back side. Press down to fully engage.
•Hang the overhead on the top of the stanchions.
•Adjust side to side to align with work surface.

Step 5: Attaching the Access Panel
•Align the access panel so the raffix connectors are in line with the studs.
•Place on studs and tighten with a Philips screwdriver by turning clockwise.

Step 6: Installing Wall Mounted Tack Board and Overhead
•Ensure work surface is level.
•Reference numbers in the table below. Measurements are to the bottom of cleat.
•Attach wall cleats. (Lag screws for a backed wall, toggles for non backed wall.)
•Install the tack board, and then the overhead.
“A” dimension
“B” dimension Open Shelf Case Overhead
A
Tack
Board Single Height Double Height Single Height Double Height
21.25” X X 31.92” 44.17”
23.5” 32.05” X34.17” X
33.5” 42.05” X44.17” X
21.84” X42.05” x X
Tack Board Work Surface to Cleat
B
21.25” 15.65”
23.5” 17.90”
33.5” 27.90”
21.85” 16.24”

Step 7: Attaching the Sliding Hood
•Remove the wing nuts from the track on the back of the overhead.
•Lifting hood over the back of the overhead, carefully align the holes on the hood with the studs in the
tracks.
•Attach wing nuts to secure hood on the overhead.

Step 8: Installing Glass Desk
•Locate the glass top (packed on its own).
•With the desk in place and properly leveled to ensure proper miter alignment, place glass top into
place.
•Use glass pods for this installation.