Nucraft Tesano Conference User manual

Tesano Conference Installation Instructions
Rev. 05/18/2016

Before Beginning Installation
•Read through the entire instruction thoroughly
•A minimum of 2 people are required for this
assembly. For 96” tables and larger it is
recommended to have 3 or 4 people available for
the install.
•These instructions reflect typical assemblies; They
may not match your specific configuration
Note: This table will be assembled right-side up
Tesano | 2

Required Tools & Hardware
Drill Driver
#2- Phillips Bit
Laser Level
¼” Allen Wrench
1 2
3 4
5 6 Tesano | 3

Tesano Conference
Tesano | 4

Tesano Exploded
1
2
5
4
6
1. Work Surface
2. Top Beams
3. Mending Plate
4. Base
5. Rail Key
6. Wire Management
7. Power Rail
7
Tesano | 5

Tesano | 6
Step 1
Connecting Rails to Bases
Run glides out of bases
before beginning assembly
Loosen bolts (#6) in the
keys attached to the beam
Insert the beams with rail
keys attached, into each of
the bases with the “THIS
SIDE UP” label facing up
and pilot holes facing
ground
Use labels to attach correct
beams to correct bases

Tesano | 7
Step 2
Installing Top
Insert pins (hardware #4) into
the holes along the top edge
of base end.
Place top onto beams, sliding
one end into the pins
(hardware #4) of one base
Repeat with the base on the
opposite end
Tighten the cams to bring
the two surfaces flush
Make sure the ends match
labels

Tesano | 8
Step 3
Securing Top with Mending Plates
Note:
-Ensure to center sides of top
to the bases prior to attaching
mending plates
-Square the base up to the top
before securing the mending
plates
Attach mending plate along
the center of the metal spacer.
Pilot holes should be present.
Attach smaller mending plates
in between the edge of the
table and the top wood rails.

Tesano | 9
Step 4a
Securing Top Rails
With the mending plates
secured in place, secure the
top beams to the wood rails
using hardware #5 long silver
screws. The pilot holes in the
beam should be facing the
ground.
Using the cap screws
(hardware #6) shown at right,
insert into side of rail keys

Tesano | 10
Step 4b
Securing Top Rails
Center the top beam between
the base and tighten cap
screws ensuring bottom of
beams are flush with one
another
Secure the top beams to the
wood rails using hardware #5
long silver screws. The screws
will go through the slotted
openings along the face of the
beam

Tesano | 11
Step 5
Fastening Aprons
Locate notch, place in apron
toward end of table
Place the aprons between the
inside of the side rail and the
black beam, and fasten them
using supplied silver screws
(hardware #2). Screws will go
through the aluminum
extrusion.

Tesano | 12
Step 6
Installing Wire Management
Step (1): Attach jumpers to receptacles
Step (2): Run the jumpers around the
table, in a u-shape design.
Step (3): At one end of the table, the
plug in-feed or hardwire should run
through the leg Jumper
Jumper
Plug-in Infeed

Tesano | 13
Step 7
Installing Wire Management Covers
Locate the wire management
channels.
Ensuring that the power duplex
lines up with the cutout, fasten the
wire management channel using
silver screws (hardware #1) and
black screws (hardware #3).
The label will be facing the top
The silver screws (hardware #1)
must be used on the raised
surface, while the black screws
(hardware #3) should be used on
the lower surface

Tesano | 14
Step 8
Installing Power Rail Unit
The power rail unit will
come with two black
brackets which should be
inserted first into the rail.
The silver bolts should be
inserted into the bracket
before inserting into rail.
Place power unit over
screws
Tighten nuts to secure unit
to the rail.