Nucraft Merino Casegood User manual

Merino Casegood Installation Instructions
Rev B –6/17/16

Before Beginning Installation
•Read through the entire instruction thoroughly
•A minimum of 2 people are required for this
assembly
•These instructions reflect typical assemblies; They
may not match your specific configuration

Required Tools & Hardware
Drill Driver
#2- #3 Phillips Bit
#2 Square Bit
3/8” Nut Driver
Laser Level
5/16” Wrench
1
2
3
4
5

Merino Free Standing

Merino Free Standing Exploded
1
24
5
3
1. Freestanding Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Tower
6
7

Merino U-Shape

Merino U-Shape Exploded
1
2
6
4
5
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Tower
8. Access Panel
9. Corner Support
10.Bridge
7
8
9
10

Merino L-Shape

Merino L-Shape Exploded
6
2
5
4
1
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Overhead Hood
8. Corner Support
9. Power Option
7
8
9

Merino T-Shape

Merino T-Shape Exploded
1
2
3
4
5
6
7
8
9
1. Desk
2. Work Surface
3. Lateral File Pedestal
4. Box, Box, File Pedestal
5. Tack Board
6. Overhead
7. Overhead Hood
8. Access Panel
9. Tower

Merino | 12
Step 1
Installing the Credenza
Locate the Pedestals and set in
place. Level.
Align work surface with mitered
edge on pedestal(s). Attach
using &
If station has additional work
surfaces, attach those the same
way and connect using mending
plates and screws
3 5
3 5
4

Merino | 13
Step 2
Attaching Corner Support
Install connector pins 1to the
work surface.
Lower the work surface onto
the corner support, aligning
the pins with the
corresponding holes in the
corner support.
Secure by turning the cams ½
turn clockwise.
1

Merino | 14
Step 3
Installing Stanchions
(If wall hung, skip to step 5)
Loosen the stanchion channel
bolts. Do not remove.
Slide the stanchions in the
channels. Adjust glides on the
stanchions until scribe line is
flush with work surface.
Tighten the stanchion channel
bolts.
Attach cross members using
3/8” bolts.
Scribe line
Work-surface
Loosen

Merino | 15
Step 4
Installing Tack Board & Overhead
Attach the tack board using
the pre installed “Z” clips on
the back side. Press down to
fully engage.
Hang the overhead on the top
of the stanchions.
Adjust side to side to align
with work surface.

Merino | 16
Step 5
Attaching theAccess Panel
Align the access panel so the
raffix connectors are in line
with the studs.
Place on studs and tighten
with a phillips screwdriver by
turning clockwise.

Merino | 17
Step 6
Installing Wall Mounted Tack Board & Overhead
Ensure work surface is level.
Reference numbers in the
table below. Measurements
are to the bottom of cleat.
Attach wall cleats. (lag screws
for a backed wall, toggles for
non backed wall.
Install the tack board.
Install the overhead.
“A” dimension
“B” dimension
Open Shelf Case Overhead
Tackboard
Single
High Double High Single High Double High
A
Tackboard
WS 2
Cleat
B
21.25”
x x 31.923” 44.173”
21.25”
15.648”
23.5”
32.049”
x 34.173” x
23.5”
17.898”
33.5”
42.049”
x 44.173” x
33.5”
27.898”
21.844”
x 42.05” x x
21.844”
16.242”

Merino | 18
Step 7
Attaching the Sliding Hood
Remove the wing nuts from
the track on the back of the
overhead.
Lifting hood over the back of
the overhead, carefully align
the holes on the hood with the
studs in the tracks.
Attach wing nuts to secure
hood on the overhead.

Merino | 19
Step 8
Installing Glass Desk
Locate the glass top. (shipped
loose)
With the desk in place and
properly leveled (leveling is
important to ensure a proper
miter alignment) place glass
top in place.
Use glass pods for this
installation.