Num'axes EASY DOG SOFT User manual

EASY DOG SOFT / EASY DOG PULSE – User’s guide – indice A 1/12
User’s guide
DECLARATION « CE » DE CONFORMITE
“EC” DECLARATION OF CONFORMITY
Directive R&TTE 1995/5/CE
NUM’AXES
déclare que / declares that
les colliers d’éducation / the training collars
EASY DOG SOFT / EASY DOG PULSE
satisfont à toutes les dispositions de la Directive N° 1999/5/CE du 07/04/99 du Conseil Européen
comply to all dispositions of the European Council Directives below N° 1999/5/CE
et sont conformes aux normes suivantes / and comply with standards below:
ETSI EN 300 220
NUM’AXES
745 rue de la Bergeresse – Z.A.C. des Aulnaies – BP 30157
45161 OLIVET CEDEX – FRANCE
Tél. + 33 (0)2 38 63 64 40 / Fax + 33 (0)2 38 63 31 00
WARNING
Any person with individual device for cardiac assistance (pacemaker, defibrillator) must take precautions
when they use EASY DOG SOFT and EASY DOG PULSE.
These devices emit some static magnetic fields (a magnet is located in the remote control).
Frequency= 869 Mhz, at = 25 mW
The devices comply with the European Standard ETSI EN 300 220.
Thank you for choosing a NUM’AXES product.
Before using your EASY DOG SOFT or EASY DOG PULSE, please read the instructions in this guide carefully and keep
it for future reference.
Before using EASY DOG, we advise you to have your dog checked by your vet to ensure it is fit
to wear a collar.
Check your dog’s neck regularly, the repeated rubbing of the contact points against the
animal’s skin may cause irritation. If this happens, remove the collar until all signs of skin
irritation have disappeared.
Do not hesitate to contact a professional trainer for any further advice.

EASY DOG SOFT / EASY DOG PULSE – User’s guide – indice A 2/12
Index Page
Contents and presentation of the EASY DOG SOFT ........................................................................... 2
Contents and presentation of the EASY DOG PULSE ......................................................................... 3
First use from new ....................................................................................................................... 3
How to use the EASY DOG SOFT remote control .............................................................................. 5
How to use the EASY DOG PULSE remote control ............................................................................. 5
Checking/replacing battery of EASY DOG SOFT or EASY DOG PULSE remote control ............................. 6
Checking/replacing battery of EASY DOG receiver collar ................................................................... 7
Changing the contact points of EASY DOG PULSE collar .................................................................... 7
How to check that your EASY DOG SOFT is functioning properly ........................................................ 7
How to check that your EASY DOG PULSE is functioning properly ....................................................... 7
Getting the best results ................................................................................................................ 7
Fitting the collar .......................................................................................................................... 8
Starting out with the training collar ............................................................................................... 8
Cautions for use .......................................................................................................................... 9
Maintenance ............................................................................................................................... 9
Troubleshooting .......................................................................................................................... 9
Technical specifications ............................................................................................................... 10
Guarantee ................................................................................................................................. 10
Guarantee conditions .................................................................................................................. 11
Spare parts ................................................................................................................................ 11
Collection and recycling of your device at the end of its life .............................................................. 11
●Contents and presentation of the EASY DOG SOFT
Contents of the product
EASY DOG receiver collar fitted with short plastic contact points and a strap
3-V CR2 lithium battery for the collar
EASY DOG SOFT remote control fitted with a 3-V CR2032 lithium battery
carry strap
this user’s guide
Presentation
VV VV
Diagram 2
COLLAR
Diagram 1
EASY DOG SOFT
REMOTE CONTROL
Plastic contact points
White mark:
area where the
On/Off switch
magnet is located
Round mark:
magnet position indicator
This magnet allows you to switch
On/Off the collar and to code the
collar with the remote control.
Indicator light:
On/Off indicator
+ radio reception indicator
+ battery level indicator
Long
vibration
button
Short
vibration
button
Beeper
button
High
luminosity
LED button
Red indicator lights:
radio transmission
indicators
+ battery level
indicators
Area where the
high luminosity
LED is located

EASY DOG SOFT / EASY DOG PULSE – User’s guide – indice A 3/12
●Contents and presentation of the EASY DOG PULSE
Contents of the product
EASY DOG receiver collar fitted with short contact points and a strap
3-V CR2 lithium battery for the collar
EASY DOG PULSE remote control fitted with a 3-V CR2032 lithium battery
pair of long contact points
neon test lamp
carry strap
this user’s guide
Presentation
●First use from new
Fitting the battery in the EASY DOG receiver collar
▪Unscrew the 4 screws of the top of EASY DOG using a screwdriver.
▪Insert the battery (3-V Lithium CR2) paying attention to follow polarity indicated on the
battery housing (ref. Diagram 5).
▪A beep sound (low pitch) is emitted, indicating the correct installation of the battery.
If you do not hear any beep after having inserted the battery, remove it immediately from its
housing. Check the polarity before trying again.
▪Before putting the lid back in place, check that the rubber seal is in its groove.
▪Screw up the 4 screws with care (do not overtighten them).
S
VVV
Diagram 4
COLLAR
Diagram 3
EASY DOG SOFT
REMOTE CONTROL
Contact points
(short or long)
White mark:
area where the
On/Off switch
magnet is located
Round mark:
magnet position indicator
This magnet allows you to switch
On/Off the collar and to code the
collar with the remote control.
Indicator light:
On/Off indicator
+ radio reception indicator
+ battery level indicator
Long
vibration
button
Stimulation
button
Beeper
button
High
luminosity
LED button
Red indicator lights:
radio transmission indicators
+ stimulation level indicators
+ battery level indicators
Area where the
high luminosity
LED is located
Seal
Diagram 5
Polarity “-”
of the battery
Polarity “+”
of the battery

EASY DOG SOFT / EASY DOG PULSE – User’s guide – indice A 4/12
Activate/deactivate the EASY DOG SOFT or EASY DOG PULSE remote control
Remote control is supplied with battery fitted.
▪Activate: as soon as the battery is in place, the remote control is ready for use.
▪Deactivate: to deactivate the remote control you have to remove the battery from its housing.
To increase the battery life of the remote control, we recommend you to deactivate the unit if you are not
using it for a long period.
Activate/deactivate the EASY DOG receiver collar
A magnet located in the EASY DOG SOFT or EASY DOG PULSE remote control is used to switch the
receiver collar On or Off.
▪Activate: move the remote control towards the collar so that the round mark on the remote control
comes into contact with the white mark on the receiver collar, hold for 1 second (ref. Diagram 6).
The indicator light on the collar will flash in green indicating that the EASY DOG receiver is On.
▪Deactivate: move the remote control towards the collar so that the round mark on the remote
control comes into contact with the white mark on the collar, hold for 1 second (ref. Diagram 6).
The indicator light on the collar will flash from green to red and then off: the EASY DOG receiver is
Off.
To increase the battery life of the receiver collar, we recommend you to deactivate the unit if you are not
using it for a long period.
Coding of the remote control and receiver collar
Each remote control has its own individual radio operator code. The coding of the remote control with the
receiver collar enables the two units to work together.
IMPORTANT: before beginning the coding (first use of the collar or re-coding), make sure no
other person is using his EASY DOG or other products from the NUM'AXES range close by: your
receiver collar could accidentally record the code of his remote control. If that occurs, re-code
the remote control with the receiver collar.
CODING PROCEDURE FOR THE 1ST USE
1. To begin the coding procedure, the remote control must be ready for use (battery in its housing).
2. Activate the collar: move the remote control towards the collar so that the round mark on the
remote control comes into contact with the white mark on the collar, hold for 1 second.
3. Move the remote control away from the receiver collar.
4. Press the button of the remote control. A beep sound is emitted; the collar is then synchronized
with your remote control.
Place these 2 areas
together during 1 second
Diagram 6
Activate/Deactivate a receiver collar
with an EASY DOG SOFT or EASY DOG PULSE remote control

EASY DOG SOFT / EASY DOG PULSE – User’s guide – indice A 5/12
RE-CODING PROCEDURE (for all coding procedures other than the 1st)
1. To begin the re-coding procedure, the remote control must be ready for use (battery in its housing).
2. Collar in position “deactivated” (indicator light off): move the remote control towards the
collar so that the round mark on the remote control comes into contact with the white mark on the
collar, hold for 6 seconds. The indicator on the collar lights in fixed green, then flashes in red.
3. Move the remote control away from the receiver collar.
4. Press the button of the remote control. A beep sound is emitted; the collar is then synchronized
with your remote control.
Reprogram an EASY DOG receiver collar
The receiver collar can be re-coded indefinitely, either with the same remote control, or with a new
one (Ref. § Re-coding procedure).
●How to use the EASY DOG SOFT remote control
The EASY DOG SOFT remote control is designed to operate with 1 receiver collar.
button: beeper
If you press the “beeper” button , the receiver collar will emit sound signals. There is no time limit for
this function: the beeper will continue to sound for as long as the button is pressed.
The central indicator light of the remote control will come on for as long as the button is pressed.
It’s up to you to use the beeper depending on the way you want to train your dog.
With the beeper you can:
send a sound to your dog when it is disobedient,
draw its attention…
It’s very important to always use the beeper in the same way in order not to disturb your dog.
button: high luminosity LED
If you press the button, you will activate a blinking red high luminosity LED on the collar for
approximately 8 minutes.
If you press the button again before the 8 minutes are over, you will stop the LED.
The central indicator light of the remote control will come on briefly.
Vbutton: short vibrations
If you press the Vbutton, the receiver collar will emit a short vibration of approximately 1 second.
The central indicator light of the remote control will come on briefly.
It’s up to you to use the vibration depending on the way you want to train your dog.
With the vibration you can:
send a sound to your dog when it is disobedient,
draw its attention…
It’s very important to always use the vibration in the same way in order not to disturb your dog.