Nureva HDL410 Service manual

Nureva HDL410 &
CamConnect Pro
Setting Guide

Copyright © Lumens. All rights reserved.
Discovering/ Enrolling HDL410
Preface:
•Accessing Nureva Console
•Enrolling HDL410 (console method)
•Editing/defining room dimensions

Copyright © Lumens. All rights reserved.
1. Access and enroll HDL410
1.1 Access Nureva console: https://www.nureva.com/software-and-services/console
Note: There are 2 methods to enroll; 1. USB method and 2. Nureva console. (Nureva console is shown here)
•For USB method see here (console client) : https://support.nureva.com/faqs-nureva-console/generate-enrollment-code-with-nureva-
console-client

Copyright © Lumens. All rights reserved.
1. Access and enroll HDL410
1.2 Enrolling HDL410 (console):
1.2.1 enter your enrollment code (located at the bottom of console- hardware).
1.2.2 You will be prompted to enter room level details- see next section

Copyright © Lumens. All rights reserved.
HDL410 Room Level Settings
Preface:
•Defining room type
•Accessing room level settings
•Editing/defining room dimensions
•Defining Room Dimensions for optimum performance
•Fine tuning room in relation to seating arrangements and
HDL410 ports
•Recalibrating HDL410 in defined room

Copyright © Lumens. All rights reserved.
2. Setting up HDL410 in room (room level settings)
2.1 Defining room type:
-Shown below is [type =Meeting room]. HDL410 supports up to 8 types (classroom, open space and others).

Copyright © Lumens. All rights reserved.
2. Setting up HDL410 in room (room level settings)
2.2 Accessing room level settings;
- Your newly created room will appear in rooms section, click on [room name] to access.

Copyright © Lumens. All rights reserved.
2. Setting up HDL410 in room (room level settings)
2.3 Editing/defining room dimensions: (HDL40 works as if were a single unit.)

Copyright © Lumens. All rights reserved.
2. Setting up HDL410 in room (room level settings)
2.4 Defining Room Dimensions for optimum performance: (this will take you to room coverage map)
Important:
1.Measure your room space and place HDL410 port 1 and 2 as precise as possible.
2. In my demo, the actual room size is bigger than the defined dimensions. For optimized performance ( to reduce reverberations, echos
and background noise).

Copyright © Lumens. All rights reserved.
2.Setting up HDL410 in room (room level settings)
2.5 Fine tuning room in relation to seating arrangements and HDL410 ports:
- An example for depiction purposes only is shown here, adjust your HDL410 port positioning as needed based on
environment and usage scenario.
- The blue spots shows noise or voice source detection.

Copyright © Lumens. All rights reserved.
2.Setting up HDL410 in room (room level settings)
2.6 Recalibrating HDL410 in defined room:
Note: After enrolling and defining room level settings, recalibrate HDL410 in finished room. This ensures all settings are kept
and HDL410 “is aware” of environmental/room level changes.
General rule = If there are room level changes, recalibrate your HDL410.

Copyright © Lumens. All rights reserved.
CamConnect Pro (AI-BOX1)
Settings

Copyright © Lumens. All rights reserved.
Connected State_AiBox and HDL410
Preface:
•Allow HDL410 to send data to CamConnect
•Three Basic connection Steps
•Fine tuning and mapping of seating positions (Azimuth
angles in CamConnect) with HDL410

Copyright © Lumens. All rights reserved.
3. Connecting CamConnect with HDL410
3.1 Allow HDL410 to send data to CamConnect.
- Use port [8931] & enter Camconnect`s IP address [Ex. 192.168.11.11].
※Nureva default port is
8931. Please confirm the
port is allowed to connect
with your PC.

Copyright © Lumens. All rights reserved.
3. Connecting CamConnect with HDL410
3.2 Three Basic connection Steps:
Below items are found under [Supported Device & Settings] HDMI/Web interface.
A. From Device drop down list select = HDL410.
B. Enter HDL410`s IP address = [example : Device IP = 192.168.11.27]. IP of HDL410 can be found as shown in 3.1.
C. Connect toggle bar set to connect = [Connect = move toggle to right].

Copyright © Lumens. All rights reserved.
Connecting CamConnect with HDL410
3.3 Fine tuning and mapping of seating positions (Azimuth angles in Camconnect) with HDL410.
-In Advanced setting of CamConnect; set the [Audio Trigger level = 65] or stay close to 60 depending on environment.
- Camconnect automatically provides 8 Azimuth Angles (these angles are adjustable for fine tuning per environment).
- In my example; I show only 4 azimuth Angles in operation; voice source is detected at [-35 ~ -18 ] then VC-TR40N preset 1 is
used to capture talker/voice source.
-Map and Adjust your azimuth angle and seating arrangements per environment, use “heat map” in Coverage map.

in
MyLumens.com Contact Lumens
Thank You!