NXP Semiconductors S32G-VNP-EVB User manual

Part Number Here
QuickStartGuide
S32Gisavehiclenetworkprocessordeliveringhighlevelsof real-timeand
applicationsprocessing,supportingCAN/LIN/FlexRaynetworkingand
GigabitEthernetinterfaceswithhardware accelerationanddeliveringahigh
levelofembeddedsecurityandASILDfunctionalsafetycapabilities.
S32G-VNP-EVB
S32G-VNP-EVB

1
www.nxp.com
Figure 1: S32G-VNP-EVB
S32G-VNP-EVB
The NXP S32G-VNP-EVB supports development, evaluation
and demonstrations with the NXP S32G274A Vehicle Network
Processor (VNP).
S32G targets applications such as:
• Central gateways, domain controllers, central compute nodes
• Firmware Over-The-Air (FOTA) updates
•Vehicle data analytics
• Secure key management
GET TO KNOW THE S32G-VNP-EVB

2
Quick Start Guide
GET TO KNOW THE S32G PROCESSOR MODULE
Figure 2: S32G-PROCEVB-S Processor Module

3
www.nxp.com
S32G-VNP-EVB Block Diagram
Figure 3 : S32G-VNP-EVB Block Diagram

4
www.nxp.com
Install S32G and Heatsink
Install the following….
✓Tera Term for console
✓FTDI CDM v2.12.28 WHQL driver
for serial configuration.
✓Win32 Disk Imager
✓Packet Sender Application
Install Software
1 3
STEP-BY-STEP INSTRUCTIONS
Open Tera Term on Windows PC.
Select the serial port to which the micro
USB J58 of the S32G-PROCEVB-Sis
connected and click OK. Go to Setup→
Serial Port and select 115200 as the
baud rate.
Setup Tera Term
Console
4
Connect the Power
Supply
2
When the S32G-PROCEVB-S is stacked
on the S32GRV-PLATEVB: Jumper J96
on the S32G-PROCEVB-S shouldbe in
position 1-2, and only the S32GRV-
PLATEVB needsto be powered. Connect
power supply to the 12V power jack P3 on
S32GRV-PLATEVB.
When the S32G-PROCEVB-S is used
standalone: Jumper 96 should be in
position 2-3. Connect power supply to the
12V power jack P1 on S32G-PROCEVB-S.
Follow the instructions in the S32G
Socket and Heat Sink User Guide
to install the S32G and heat sink.
You can watch this video (available
in this directory if video doesn’t play
in browser) to see the installation
process.

5
www.nxp.com
5
STEP-BY-STEP INSTRUCTIONS
Power ON the
S32G-VNP-EVB
The Diagnostics Utility is auto-
executed from the SD card. Console
display on Tera Term shows the
status of the diagnostic tests.
Diagnostics Utility
6
Switch ON the power switch SW1 on the
S32GRV-PLATEVB and power switch
SW10 on the S32G-PROCEVB-S.

6
www.nxp.com
Reference Links for Useful Documents
1. S32G Socket and Heatsink User Guide
2. Video- Installing the S32G in the EVB Socket
3. S32 VNP EVB Platform Board design details
4. S32G-PROCEVB-S design details
5. S32G Hardware Design Guide
6. S32G Boot Process Application Note
7. S32G-VNP-EVB User Guide
8. SD card program image (in Diagnostics SW deliverable)
9. SD card image logs

www.nxp.com/S32G-VNP-EVB
NXP and the NXP logo are trademarks of NXP B.V. All other product or service names are the property of their
respective owners. © 2019 NXP B.V.
SUPPORT
Visit www.nxp.com/support for a list of
phonenumbers within your region.
WARRANTY
Visit www.nxp.com/warranty for complete
warranty information.
Get Started
Download installation software
and documentation under
“Jump Start Your Design” at
nxp.com/S32G-VNP-EVB.
Document Number: S32G-VNP-EVBQSG REV 0