NXP Semiconductors Intrinsyc Open-X 8M User manual

Open-X™ 8M Development Kit
Quick Start Guide
Your use of this document is subject to and governed by those terms and condions in the Intrinsyc Purchase and Soware License Agreement for the Open-X™ 8M Development Kit based on the NXP i.MX 8M Processor, which you or the legal enty you represent, as the case may be,
accepted and agreed to when purchasing an Open-X™ 8M Development Kit from Intrinsyc Technologies Corporaon (“Agreement”). You may use this document, which shall be considered part of the dened term “Documentaon” for purposes of the Agreement, solely in support of
your permied use of the Open-X™ 8M Development Kit under the Agreement. Distribuon of this document is strictly prohibited without the express wrien permission of Intrinsyc Technologies Corporaon and its respecve licensors, which they can withhold, condion or delay in its
sole discreon. Intrinsyc and Open-X are trademarks of Intrinsyc Technologies Corporaon, registered in Canada and other countries. Other product and brand names used herein may be trademarks or registered trademarks of their respecve owners.
Package Contents
1. 12V DC input jack
2. Debug UART (USB MicroB)
3. Power on-o switch
4. Gigabit Ethernet connector
5. USB Type-C connector
6. 3.5 mm audio line-out jack
7. USB Type-A host port
8. USB select switch
9. HDMI video output
10. SOM current sense connector
11. Wi-Fi/BT module
12. MIPI CSI 2 camera connector
13. NXP i.MX 8M SoC
14. Micro SD card slot (on boom)
15. Open-X 8M System on Module
16. MIPI CSI 1 camera connector
17. WLAN PCB Antenna 1
18. Boot conguraon DIP switches
19. 4 x LEDs
20. FPC digital audio expansion
connector (on boom)
21. Digital audio expansion headers
22. Power, reset, and user buons
23. MIPI DSI LCD/touchscreen
connector to interface with
Intrinsyc display adapter
24. WLAN PCB Antenna 2
25. JTAG header
26. PCIe M.2 Socket (on boom)
27. Fan power on-o switch
28. Fan power header
1. Open-X™ 8M SOM with NXP i.MX 8M processor
2. Open-X™ 8M Carrier board
3. AC Power Adapter
4. HDMI Video Cable
5. 4.5” FWVGA MIPI DSI LCD/touchscreen (oponal accessory)
134
9
12
19
24
25
10
13
8
17
16
28
23
27
25
11
21
67
1822
14
26
15
20

Open-X™ 8M Development Kit
Quick Start Guide
Development Kit Support
For more information or assistance, you can contact us at:
https://www.intrinsyc.com/contact-support
Intrinsyc also provides technical information and videos on our products at:
https://www.intrinsyc.com/resources/
Should you require additional technical support for your Development Kit you can
purchase a block of technical support hours from the Intrinsyc store:
https://www.intrinsyc.com/support
Thank you for purchasing the Open-X 8M Development Kit
The Intrinsyc Team
Development Kit Setup
1. At a static-safe workstation, remove the development kit board
carefully from the anti static bag
2. If you do not have the optional LCD then connect the HDMI cable from
the development kit to an HDMI display.
3. Connect the Power Adapter to the 12V DC jack, switch the power
switch (3) to the ON position, then press and hold the power button (22)
for approximately 3 seconds. On the LCD or HDMI monitor you will see
the Intrinsyc logo as the board boots up, followed by the OS desktop.
4. Documentation and software
To access the documentation (schematics, user guides, programming guides,
tech notes…), platform BSP software and much more, please register at:
http://support.intrinsyc.com
Specicaons are subject to change - Open-X 8M DevKit QSG rev 1.2