NXP Semiconductors NTAG I2C plus Use and care manual

Document information
Info Content
Author Pavel Slamnik
Author Role Design Engineer
Keywords NTA I2C plus Explorer Kit OM5569-NT322E, RFID, NFC, TA , NTA
Hardware Manual: NTA I2C plus Explorer
Kit OM5569/NT322E
Doc Rev 1.00 Approved — 2015.09.01 BL ID

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Revision History
Revision Date Description Author
1.01 2015.12.07 First Version Pavel Slamnik
Copyright: @2009, NXP Semiconductors
The information contained herein is the exclusive and confidential property of NXP Semiconductors and, except as
otherwise indicated, shall not be disclosed or reproduced in whole or in part.
SRS Template_vs 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 2 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
1. NTAG I2C plus Explorer it OM5569/NT322E: Photo
Figure 1: NTA I2C plus Explorer Kit OM5569/NT322E – Connected Tags Explorer Board
with NTA I2C plus Antenna Board 54 x 27mm (pcb type).
Figure 2: Connected Tags Explorer Board OM5569, Rev 2.0.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 3 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Figure 3: NTA I2C plus Antenna Board OM5569/NT322E, 54 x 27 mm.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 4 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
2. NTAG I2C plus Explorer it OM5569/NT322E: Description
2.1. Operational desription
To demonstrate the unique properties of the NTA I2C tag chip, NXP developed the NTA
I2C plus Explorer Kit OM5569/NT322E which consists from Connected Tags Explorer Board
OM5569 and one NTA I2C plus Antenna Board OM5569/NT322E (54 x 27 mm ).
NXP’s NTA I2C plus Explorer Kit is an all-in-one demonstration/development resource for
NFC connected tags. Designed to emulate using an NTA I2C tag chip in an embedded
electronic system, the kit centers around a multi-purpose microprocessor-based
development/Explorer board, and includes a full complement of hardware and software tools
to support investigation of the NTA I2C chip operation, the NFC RF communication link,
and the I2C serial bus connected link; perform a variety of demonstrations; and develop/test
your own applications.
NTA I2C tag chips mounted on a variety of different antenna types (FR4 PCB-based with
separate antenna pads for custom antenna use, as well as a Flex antenna board based for
easier product insertion testing) and with built-in I2C serial bus interface connectors.
The Connected Tags Explorer board contains an NXP microcontroller (LPC11U24 Cortex-
M0), a R B (red - green - blue) LED and OB (orange – blue – green) push button as well
as an NXP temperature sensor (PCT 2075) and an LCD screen to show the messages
coming from the NTA and the application. NTA I2C plus Antenna Board contains NTA
I2C intergated circuits (NT3H1101/NT3H1201) and pcb wired (or flex) antenna. Connection
between these two boards is via I2C serial link.
The Android application, called NTA I2C Demo, can be found and freely downloaded from
the oogle Play Store. This document applies to the NTA I2C Demoboard application
version 1.5 and above. The Android application is intended to operate on devices running
Android version 4.0 and beyond. The application has been optimized for a correct visioning
of the graphical elements in smartphones featuring different resolutions.
The NTA I2C Android App is meant to be working with the Connected Tags Explorer board,
and an adjacent PCB or flex antennas to test all the features and functionalities the NTA
I2C is offering.
USB port and JTA port are used only for writing firmware into LPC11U24 microcontroller
and for debbuging purposes.
The below picture is a view of the Connected Tags Explorer board and the NTA I2C plus
Antenna Board 54 x 27 mm.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 5 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Figure 4: Connected Tags Explorer board with NTA I2C plus Antenna Board 54 x 27 mm.
Figure 5: Connected Tags Explorer Board with NTA I2C plus Antenna Board and NFC
device – princip of operation.
Disclaimer :
This module is intended only for development and evaluation purposes, and cannot be used
in a finished product.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 6 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Figure 6: Connected Tags Explorer Board Rev. 2.0 with NTA I2C plus Antenna Board –
Block diagram.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 7 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Figure 7: Connected Tags Explorer Board OM5569, Rev. 2.0: dimensions and equipped pcb
with connectors.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 8 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
Figure 8: NTA I2C plus Antenna Board OM5569/NT322E, 54 x 27mm, Rev. 2.0:
dimensions and equipped pcb with connector.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 9 of 18

BL ID Hardware Manual
Project Name: Integration Manual Project ID: 62743
3. NTAG I2C plus Expolorer it OM5569/NT322E: SPECIFICATION
3.1. Connected Tags Explorer Board OM5569: Specifications
Table 1: Connected Tags Explorer Board OM5569, Rev. 2.0 – specifications:
Low Power Microcontroller
LPC11U24 (Cortex - M0)
Oscillator
Internal oscillator (in LPC11U24) up to 12 MHz, Quartz 12 MHz
On-board sensor
Temperature Sensor PCT2075
Output/Input
Outputs 3 x LED (orange, green, blue)
Inputs 3 x key
Supported Interfaces (6-pin connector to NTA I2C Antenna Board)
I2C I2C-bus interface to up to 100 kBd (Standard mode), up to 400 kBs
(Fast mode)
LCD display
2 x 16 character, WLED backlight, I2C serial communication, 3V3
power supply
Supported Interfaces
USB serial interface USB 2.0 interface (also supported Usb 1.1), 12 Mbps (USB 2.0 full
speed), micro usb connector
ISP JTA interface (10-pin header) for ISP programming with
LPCXpressoBoard
Electrical and Mechanical Specifications
Power Supply Board is powered from NTA I2C Antenna Board (from NTA I2C
tag ic); usb power is used only for powering lcd backlight (20 mA)
PCB Dimensions (L x W x
H)
70 mm x 38 mm x 14 mm
Weight approx. 22 g
Operating Temperature 0… + 50 C (without condensing)
Operating Humidity 5 … 95% RH
Certificates CE, FCC
Note:
USB port and JTA port are used only for writing firmware into LPC11U24 microcontroller
and for debbuging purposes.
SRSt Template 1.0 public © NXP B.V. 2015. All rights reserved
Doc ID: DOC-XXXXXX Doc Rev 1.00 Approved — 2015.09.01 10 of 18