Oase Aquarius Eco Expert 28000 User manual

42423/09-16-MH
Aquarius Eco Expert 22000/28000
42423 GA Aquarius_Eco_Expert_end_. 13.09.16 16:48 Seite 2

--
2
A
B
ARS0033
ARS0034
C
ARS0025
D
ARS0026

--
3
E
ARS0027
F
ARS0030

--
4
G
ARS0029
H
ARS0028

--
5
I
ARS0031

-EN -
13
-EN -
Translation of the original Operating Instructions
WARNING
•This unit can be used by children aged 8 and above and by per-
sons with reduced physical, sensory or mental capabilities or lack
of experience and knowledge if they are supervised or have been
instructed on how to use the unit in a safe way and they understand
the hazards involved.
•Do not allow children to play with the unit.
•Only allow children to carry out cleaning and user maintenance un-
der supervision.
•Ensure that the unit is fused for a rated fault current of max. 30 mA
by means of a fault current protection device.
•Only connect the unit if the electrical data of the unit and the power
supply correspond. The unit data is to be found on the unit type plate,
on the packaging or in this manual.
•Possible death or severe injury from electrocution! Before reaching
into the water, always disconnect all units in the water that have a
voltage of >12 V AC or >30 V DC from the power supply.
•Only operate the unit if no persons are in the water.
•Do not use the unit if electrical cables or housings are damaged.
•A damaged connection cable cannot be replaced. Dispose of the
unit.
Safety information
Correct electrical installation
•Electrical installations must meet the national regulations and may only be carried out by a qualified electrician.
•A person is regarded as a qualified electrician if, due to his/her vocational education, knowledge and experience, he
or she is capable of and authorised to judge and carry out the work commissioned to him/her. This also includes the
recognition of possible hazards and the adherence to the pertinent regional and national standards, rules and regula-
tions.
•For your own safety, please consult a qualified electrician.
•Extension cables and power distributors (e.g. outlet strips) must be suitable for outdoor use (splash-proof).
•Protect the plug connection from moisture.
•Only connect the unit to a correctly fitted socket.

-EN -
14
Safe operation
•The impeller unit in the pump contains a magnet with a strong magnetic field that may affect the operation of pace-
makers or implantable cardioverter defibrillators (ICDs). Always keep magnets at least 0.2 m away from implanted
devices.
•Never carry or pull the unit by the electrical cable.
•Route cables such that they are protected from damage and do not present a tripping hazard.
•Never carry out technical changes to the unit.
•Only carry out work on the unit described here.
•Only use original spare parts and accessories for the unit.
Information about these operating instructions
Welcome to OASE Living Water. You made a good choice with the purchase of this product Aquarius Eco Expert
22000/28000.
Prior to commissioning the unit, please read the instructions of use carefully and fully familiarise yourself with the unit.
Ensure that all work on and with this unit is only carried out in accordance with these instructions.
Adhere to the safety information for the correct and safe use of the unit.
Keep these instructions in a safe place! Please also hand over the instructions when passing the unit on to a new
owner.
Symbols used in these instructions
Warnings
The warning information is categorised by signal words, which indicate the extent of the hazard.
WARNING
•Indicates a possibly hazardous situation.
•Non-observance may lead to death or serious injuries.
CAUTION
•Indicates a possibly hazardous situation.
•Non-observance may lead to slight or minor injuries.
NOTE
Information for the purpose of clarification or for preventing possible damage to assets or to the environment.
Additional information
A Reference to a figure, e.g. Fig. A.
→Reference to another section.
Scope of delivery
A
Aquarius Eco Expert 22000/28000
1
Filter pump with filter housing (2)
2
Filter housing
3
Stand
4
38 mm (1½ ‘‘) hose connector
5
50 mm (2 ‘‘) hose connector
6
Union nut 50 mm (2 ‘‘) for fastening the hose connector (4)
7
Flat seal 45 × 33 × 3 mm for the hose connector (4)
8
Hose clip 40 … 60 mm

-EN -
15
Product Description
B
Aquarius Eco Expert 22000/28000
1
Pump casing
•The position of the outlet can be changed by fitting the pump casing rotated through 90°.
2
Outlet (pressure socket)
3
Inlet (suction socket)
4
Filter housing
5
Stand
•Ensures secure and stable positioning of the pump.
•Can be firmly bolted to the ground.
6
Connection OASE Easy Garden Control (EGC)
•The pump can be controlled via EGC with Eco Control or InScenio FM-Master WLAN (optional).
•This manual does not contain a description of the connection and operation of EGC. For information please contact your specialist dealer
or OASE.
Important: Moisture at the connections can damage the pump.
•Only remove the protection caps for connecting the EGC lines.
•Ensure that the rubber seals are clean and fit exactly.
•Replace damaged rubber seals.
7
Switch for switching on/switching off the Dynamic Function
Properties
•Excellent delivery rates meeting the requirements of demanding filter systems and large water courses and waterfalls.
•Can deal with coarse debris with a particle size of up to 4 mm.
•Ergonomic handle for safe transport.
•Suitable for immersed or dry installation.
•Unique, patented frost protection: The pump is guaranteed to operate without damage at temperatures as low as
-20 °C.
•Suitable for swimming ponds and natural swimming pools (installed in an external pump chamber).
Dynamic Function
Different values for the pump flow rates are pre-programmed in the pump control system to allow a dynamic fountain
pattern with changing heights and diameters. When the Dynamic Function is activated, the pump is continuously con-
trolled with these values.
Intended use
Aquarius Eco Expert 22000/28000, referred to as "unit", may only be used as specified in the following:
•Pumping of normal water for creating fountains.
•Operate in accordance with instructions.
•Operation under observance of the permissible water quality. (→Water quality)
The following restrictions apply to the unit:
•Do not use in swimming ponds.
•Never use the unit to convey fluids other than water.
•Never run the unit without water.
•Do not use for commercial or industrial purposes.
•Do not use in conjunction with chemicals, foodstuff, easily flammable or explosive substances.
•Do not connect to the domestic water supply.

-EN -
16
Installation and connection
WARNING
Possible death or severe injury from hazardous electrical voltage!
•Prior to reaching into the water, isolate (switch off and disconnect) all units/devices used in the water.
•Isolate the device (disconnect from the power supply) before carrying out any work on it.
WARNING
Death or serious injuries from hazardous electrical voltage due to operation of this unit in a swimming pond.
•Never operate this unit in a swimming pond.
Operating the unit in the pond
C
•Never operate the pump in a swimming pond.
•Only operate the pump when it is below the water surface level.
•Only operate the pump with the filter basket fitted.
•Ensure that the pump is in a secure and stable position.
NOTE
If the pump is used for conveying excessively soiled water, the impeller unit will be subject to increased wear
and will require earlier replacement.
Remedy:
•Thoroughly clean the pond or pool before installing the pump.
•Install the pump approx. 200 mm above the floor of the pond to avoid excessively soiled water from being
drawn into the pump.
How to proceed:
E
1. Screw the stepped hose adapter including union nut and sealing ring to the outlet.
2. Slip the hose clip over the hose, fit the hose onto the hose connector and secure with the hose clip.
Install the unit at a dry place
D
•Swimming pond or pool that may be accessed by people.
– Install the unit at least 2 m away from the water.
•Do not expose the unit to direct sunlight.
•Ensure that the pump is in a secure and stable position.
How to proceed:
F
1. Remove the screws for fastening the filter basket and remove the filter basket.
2. Screw the hose connector with union nut and seal onto the inlet.
3. Slip the hose clip over the hose, fit the hose onto the hose connector and secure with the hose clip.
4. Screw the hose connector with union nut and seal onto the outlet.
5. Slip the hose clip over the hose, fit the hose onto the hose connector and secure with the hose clip.
6. Fasten the pump to a suitable base using screws (not included in the scope of delivery).
NOTE
Recommendations for hoses and pipes:
•Use 50 mm (2 ") hose connectors and hoses for a length of up to 5 m.
•Use DN 75 or DN 100 pipes for a length greater than 5 m.

-EN -
17
Commissioning/start-up
NOTE
Sensitive electrical components. Incorrect connection will destroy the unit.
•Do not connect the unit to a dimmable power supply.
When started up, the pump automatically performs a pre-programmed self-test of approx. two minutes length (Envi-
ronmental Function Control (EFC)). The pump detects if it is running dry / blocked or submerged. The pump
switches off automatically after approx. 90 seconds if it runs dry (is blocked). In the event of a malfunction, disconnect
the power supply and flood the pump or remove the obstacle. Following this, the unit can be restarted.
Switching on: Connect the unit to the mains. The unit switches on immediately.
Switching off: Disconnect the unit from the mains.
Dynamic Function
How to proceed:
G
•Slide the switch.
– ON: The function is activated.
– OFF: The function is deactivated.
NOTE
When the Dynamic Function is activated, the function of the EFC (Environmental Function Control) is limited.
•The unit is not protected from running dry.
Remedy of faults
Malfunction
Cause
Remedy
Pump does not start
No mains voltage
−Check the mains voltage
−Check supply lines
Pump does not deliver
Filter housing clogged
−Clean
Excessively soiled water
−Clean pump. The pump automatically
switches on again once the motor has
cooled down.
Impeller unit blocked
−Disconnect the power supply and remove
obstacle. Then switch the pump on again.
Insufficient delivered quantity
Filter housing clogged
−Clean
Excessive loss in the supply lines
−Select larger hose diameter
−Reduce hose length to reduce frictional
loss
−Avoid unnecessary connection elements
Pump switches off after a short running period
Excessively soiled water
−Clean pump. The pump automatically
switches on again once the motor has
cooled down.
Water temperature too high
−Note maximum water temperature of
+35°C. The pump automatically switches
on again once the motor has cooled down.
Impeller unit blocked
−Disconnect the power supply and remove
obstacle. Then switch the pump on again.
Pump has run dry.
−Flood pump. Fully submerge the unit when
operated in the pond.