OHAUS Courier 7000 User manual

Courier 7000
Instruction Manual

REVISION HISTORY
Date
Version
Description
March 30, 2023
A
Initial release
July 7, 2023
B
Updated the company address in the back cover and FCC page

Courier 7000 EN-1
TABLE OF CONTENTS
1. INTRODUCTION .........................................................................................................................................3
1.1. Safety Precautions ...................................................................................................................................3
1.2. Intended Use ............................................................................................................................................3
1.3. Overview of Parts and Controls ...............................................................................................................4
1.4. Control Functions .....................................................................................................................................4
2. INSTALLATION...........................................................................................................................................6
2.1 Packing List ..............................................................................................................................................6
2.2 Unpacking the Scale ................................................................................................................................6
2.3 Setup ........................................................................................................................................................7
2.3.1 Power Supply Connection.................................................................................................................7
2.3.2 PC Connection..................................................................................................................................7
2.3.3 Direct Wall Mounting .........................................................................................................................8
2.3.4 2nd Display Installation (available as option)....................................................................................8
2.4 Leveling the Equipment......................................................................................................................... 10
3. OPERATION............................................................................................................................................. 11
3.1 Turning On/Off the Scale ...................................................................................................................... 11
3.2 Setting the Display to Zero.................................................................................................................... 11
3.3 Changing the Units of Measure............................................................................................................. 11
3.4 Printing Data.......................................................................................................................................... 11
3.5 Application Modes ................................................................................................................................. 11
3.5.1 Weighing ........................................................................................................................................ 11
3.5.2 Totalization..................................................................................................................................... 12
3.5.3 Dynamic Weighing ......................................................................................................................... 13
3.5.4 Weight Alert.................................................................................................................................... 15
4. MENU SETTINGS .................................................................................................................................... 16
4.1 Menu Navigation ................................................................................................................................... 16
4.1.1 User Menu (In segments) .............................................................................................................. 16
4.1.2 Button Navigation........................................................................................................................... 17
4.2 Calibration Menu ................................................................................................................................... 17
4.2.1 Initial Calibration............................................................................................................................. 18
4.2.2 Zero Calibration [ZErO] ................................................................................................................... 18
4.2.3 Span Calibration [SpaN] .................................................................................................................. 18
4.2.4 Linearity Calibration [LIN] ............................................................................................................... 19
4.2.5 GEO Code Adjustment [GEO] .......................................................................................................... 19
4.2.6 Calibration Test [C.test] ................................................................................................................. 20
4.2.7 End Cal [End] ................................................................................................................................. 20
4.3 Setup Menu ........................................................................................................................................... 20
4.4 Readout Menu....................................................................................................................................... 21
4.5 Unit Menu .............................................................................................................................................. 23
4.6 RS232 Menu ......................................................................................................................................... 23
4.7 Print Menu ............................................................................................................................................. 24
4.8 Lock Button Configuration ..................................................................................................................... 27
5. LEGAL FOR TRADE................................................................................................................................ 28
5.1 Settings ................................................................................................................................................. 28
5.2 Verification............................................................................................................................................. 28
5.3 Sealing .................................................................................................................................................. 29
6. COMMUNICATION................................................................................................................................... 30
6.1 UPS WorldShip / FedEx Software Compatibility................................................................................... 30
6.1.1 UPS WorldShip .............................................................................................................................. 30
6.1.2 FedEx............................................................................................................................................. 32
6.2 Scale to Device Port Connections......................................................................................................... 34
6.2.1 USB (Type C) Port ......................................................................................................................... 34
6.2.2 RS232 Port..................................................................................................................................... 35
6.2.3 Other Options (2nd RS232 or Ethernet or WiFi / Bluetooth or 2nd Display) ................................. 36
6.3 Interface Protocols ................................................................................................................................ 36
6.3.1 NCI Protocol................................................................................................................................... 36
6.3.2 8213 Interface Protocol.................................................................................................................. 37
6.3.3 3835 Protocol ................................................................................................................................. 40
6.3.4 NCI-SCP01 Protocol ...................................................................................................................... 41
7. MAINTENANCE ....................................................................................................................................... 43
7.1 Cleaning ................................................................................................................................................ 43
7.2 Troubleshooting..................................................................................................................................... 43

EN-2 Courier 7000
7.3 Service Information ............................................................................................................................... 43
8. ACCESSORY ........................................................................................................................................... 44
9. TECHNICAL DATA .................................................................................................................................. 46
9.1 Specifications ........................................................................................................................................ 46
9.2 Drawings and Dimensions .................................................................................................................... 48
9.3 Table of GEO Code Values................................................................................................................... 49
10. COMPLIANCE.......................................................................................................................................... 50
11. APPENDICES........................................................................................................................................... 52
11.1 MT Standard Continuous Output .......................................................................................................... 52
11.2 MT-SICS Commands ............................................................................................................................ 54
11.3 OHAUS Commands .............................................................................................................................. 55
11.4 OH-Continuous Print ............................................................................................................................. 56
11.5 Column Kit Installation........................................................................................................................... 57
LIMITED WARRANTY ........................................................................................................................................ 58

Courier 7000 EN-3
1. INTRODUCTION
This manual contains installation, operation, and maintenance instructions for Courier 7000. This instruction
manual helps you to install and use this scale easily. Therefore, you must read it carefully before installation
and operation.
1.1. Safety Precautions
Definition of Signal Warnings and Symbols
Safety notes are marked with signal words and warning symbols. These show safety issues and warnings.
Ignoring the safety notes may lead to personal injury, damage to the instrument, malfunctions and false results.
Signal Words
WARNING
For a hazardous situation with medium risk, possibly resulting in severe injuries or
death if not avoided.
CAUTION
For a hazardous situation with low risk, resulting in damage to the device or the
property or in loss of data, or minor or medium injuries if not avoided.
ATTENTION
For important information about the product. May lead to equipment damage if not
avoided.
NOTE
For useful information about the product.
Warning Symbols
General hazard Explosion hazard Electrical shock hazard
Safety Precautions
CAUTION: Read all safety warnings before installing, making connections, or servicing this
equipment. Failure to comply with these warnings could result in personal injury and/or property
damage. Retain all instructions for future reference.
Before connecting power, verify that the equipment’s input voltage range and plug type are
compatible with the local AC mains power supply.
Do not position the equipment such that it is difficult to reach the power connection.
Make sure that the power cord does not pose a potential obstacle or tripping hazard.
Operate the equipment only under ambient conditions specified in these instructions.
The equipment is for indoor use only.
Do not operate the equipment in wet, hazardous, or unstable environments.
Do not allow liquids to enter the equipment.
Do not load the equipment above its rated capacity.
Do not drop loads on the platform.
Do not place the equipment upside down on the platform.
Use only approved accessories and peripherals.
Disconnect the equipment from the power supply when cleaning.
Service should only be performed by authorized personnel.
WARNING: Never work in an environment subject to explosion hazards! The housing of the
instrument is not gas tight. (Explosion hazard due to spark formation, corrosion caused by the
ingress of gases)
WARNING: Electrical shock hazards exist within the housing. The housing should only be opened by
authorized and qualified personnel. Remove all power connections to the unit before opening.
1.2. Intended Use
This instrument is intended for use in pharmacies, schools, businesses and light industry. It must only be used
for measuring the parameters described in these operating instructions. Any other type of use and operation
beyond the limits of technical specifications, without written consent from OHAUS, is considered as not
intended. This instrument complies with current industry standards and the recognized safety regulations;
however, it can constitute a hazard in use. If the instrument is not used according to these operating
instructions, the intended protection provided by the instrument may be impaired.

EN-4 Courier 7000
1.3. Overview of Parts and Controls
Figure 1-1 i- Courier 7000
Item
Description
Item
Description
1
Front Housing
6
RS232 Connector
2
Control Panel
7
USB Type-C Connector
3
Rear Housing
8
Mini DIN Connector
4
Screws (4)
9
Load Cell Connector
5
Battery Cover
1.4. Control Functions
Figure 1-2 i- Courier 7000 Control Panel
1
2
4
5
3
6
7
8
9

Courier 7000 EN-5
Button
Primary Function
(Short Press)
On/Zero
If the scale is off,
short press to turn
on the scale.
If the scale is on,
short press to set
the display value
to zero.
Print
If an interface is
enabled, the current
display value can be
transmitted to the
interface port.
Function
This key initiates
the specific
function in
different
application modes.
Tare
Performs a tare
operation.
Secondary
Function
(Long Press)
Off
If the scale is on,
long press to turn
off the scale.
Units
Changes the
weighing unit.
Mode
Changes the
application mode.
Menu
Enters the user menu.
Menu Function
(Short Press)
Yes
Selects the
current setting on
the display or
goes into a sub-
menu.
No
Moves to the next
menu or menu item.
Rejects the current
setting on the
display and moves
to the next available
one.
Back
Moves back to the
previous menu
item.
Exit
Exits the user menu.
Aborts a calibration in
progress.
NOTE:
•Short Press: Press the key less than 1 second.
•Long Press: Press and hold the key for more than 3 seconds.
Figure 1-3 Display
Item Description Item Description
1
Net weight symbol
7
Pound, Ounce, Pound:Ounce symbols
2
Preset Tare, Tare symbols
8
Kilogram, gram symbols
3
Negative symbol
9
Dynamic Weighing mode symbol
4
Totalization symbol
10
Pieces symbol
5
Stable weight symbol
11
Battery symbol
6
Center of Zero symbol
1
2
3
4
5
6
11
10
9
8
7

EN-6 Courier 7000
2. INSTALLATION
2.1 Packing List
Item
Description
Picture
Quantity
1 Courier 7000 scale 1
2 USB cable 1
3 AC adapter 1
2.2 Unpacking the Scale
Steps
1. Take out the documents, cable and power adapter,
then put them to the side.
2. Remove the foam blocks.
3. Take the Courier 7000 scale out of the box and put
it on a stable surface.
NOTE: For i-C71M150X, please refer to the
pictures on the right to carry the Courier 7000
scale.
4. Remove the platform and 4 red shipping tabs
between the upper and lower frames of the scale's
base.
Shipping tab Platform
Foam
block
2
1

Courier 7000 EN-7
2.3 Setup
2.3.1 Power Supply Connection
The Type-C cable and the AC adapter can supply power to the scale.
USB Power
1. Use the Type-A end of the USB cable to connect to the
PC.
Type-C
2. Use the other side of the USB cable to connect the
terminal through the mounting hole in the bracket.
AC Adapter Power
1. Use the Type-A end of the USB cable to connect to
the AC adapter.
2. Use the other side of the USB cable to connect the
terminal through the mounting hole in the bracket.
3. Plug the AC Adapter into the electrical outlet.
Type-C
Dry Battery Power
4 disposable AA size dry batteries (not included) can supply power to the scale.
1. Loosen the 2 screws on the terminal mounting bracket
to remove the terminal.
2. Install the batteries in the battery compartment.
The battery symbol indicates the battery status:
Battery 5%~25% remaining
Battery 50%~75% remaining
Battery 25%~50% remaining
Battery 75%~100% remaining
2.3.2 PC Connection
USB to PC
USB is the preferred method of connection. If you connect a USB cable to the PC, it allows the USB
communication with the PC.
NOTE: The USB cable to a PC connection can supply power to the scale as well.
1. Use the Type-A end of the USB cable to connect to the
PC.
Type-C
2. Use the other side of the USB cable to connect the
terminal through the mounting hole in the bracket.
PC
Type A
Mounting hole
Battery
PC
Mounting hole
AC adapter
Mounting
hole
Type-A

EN-8 Courier 7000
RS232 to PC
The RS232 is the alternative method of the connection.
1. Connect the RS232 cable to the terminal through the
mounting hole in the bracket.
RS232
2. Connect the other side of the RS232 cable to the PC.
(Typically labeled COM 1, COM A or IOIOI).
3. To supply power, you can use the USB cable and AC
adapter or the dry batteries (Refer to 2.3.1 Power
Supply Connection).
NOTE:
Connections can also be made using the options for a 2nd RS232, Ethernet or WiFi/Bluetooth connection via
the Mini DIN connection. More details about each connection is found in the manuals for each option. Once an
option is connected to the scale, the menu will then show options for configuring the connection.
2.3.3 Direct Wall Mounting
The terminal may be mounted directly to a wall using two screws (not included).
1. Remove the cable ties on the bottom of the scale to
release the load cell cable.
Load cell cable
2. Loosen the 2 screws on the terminal mounting bracket
to remove the terminal.
3. Select appropriate size screws that fit into the holes at
the bottom of the terminal housing. See Figure A.
When mounting to a wall without a solid backing, use
appropriate anchoring hardware.
Figure A. Direct Wall Mount Arrangement
2.3.4 2nd Display Installation (available as option)
OHAUS offers a remote 2nd Display as an option which can be either mounted to a wall or desk, or mounted
on an optional column. Commonly this is used for displaying weight results to a customer in a retail application.
The remote 2nd Display connects to the Courier 7000 terminal using the Mini DIN connection – when
connected, the other connection options (2nd RS232, Ethernet or WiFi/Bluetooth) cannot be also connected.
Wall-Mounted Display
The 2nd display may be mounted directly to a wall using two screws (not included).
1. Use the male end of the 2nd display to connect
the Mini DIN on the terminal through the hole on
the terminal mounting bracket.
2. Select appropriate size screws that fit into the
holes at the bottom of the housing. See Figure
B. When mounting to a wall without a solid
backing, use appropriate anchoring hardware.
Figure B. Direct Wall Mount Arrangement
Male end
Hole
100mm/3.9''
Cable tie
139mm/5.5''

Courier 7000 EN-9
Column Kit Display
To install the 2nd display on the column kit:
1. Use the male end of the 2nd display to connect
the Mini DIN of the terminal through the column
kit.
Column kit Male end
2. Install the 2nd display on the column kit.
3. Install the column kit to the countertop with the
screws.
All the options can work via the Mini DIN connector on the Courier 7000 scale. Refer to the figure 2-1, you can
find the pinouts definition for the Mini DIN.
Figure 2-1 Courier 7000 Mini DIN
Item
Function (color)
Item
Function (color)
1
GND
5
CTS
2
VCC
6
RTS
3
TXD
7
P_EN
4
RXD
8
Option_DCT
7
8
5
2
1
3
6
4
Column kit
2nd display

EN-10 Courier 7000
2.4 Leveling the Equipment
To ensure accuracy, proper performance and safety, locate and operate the base on a stable, level surface.
Avoid locations with rapid temperature changes or excessive dust, air currents, vibrations, electromagnetic
fields or heat.
Level the base by adjusting the four leveling feet until the bubble in the level indicator is centered. A wrench
may be needed to loosen the locking nut above each leveling foot. When the base is level, retighten the
locking nuts up against the base to lock each foot into place.
NOTE: Ensure that the base is level each time its location is changed.
Correct Incorrect

Courier 7000 EN-11
3. OPERATION
3.1 Turning On/Off the Scale
To turn on the scale, you can press the On button. The scale performs a display test, and momentarily displays
the software version, the GEO value and then enters the last active weighing mode.
NOTE: If the hardware lock switch is enabled, LFt ON will also be displayed briefly.
To turn the scale off, you can long press the Off button until OFF is displayed.
3.2 Setting the Display to Zero
The value of the display can be set to zero under the following conditions:
1. Automatically at Power On (Initial zero).
2. Semi-automatically (Manually) by pressing the ON/ZERO Off button.
3. Semi-automatically by sending the Zero command (Z or alternate zero command).
If you want to set the value of the display by pressing the ON/ZERO Off button, please make sure that the
scale is stable.
3.3 Changing the Units of Measure
To change the weighing unit, you can long press the Print Units button until the wanted weighing unit appears
on the display.
3.4 Printing Data
Before you print out the displayed data with a printer or sending the data to a computer, please set the
communication parameters in the Print Menu (Refer to 4.7 Print Menu).
You can press the PRINT Units button for sending the displayed data to the communication port.
3.5 Application Modes
Activating / Deactivating the Application Mode
To activate or deactivate the application mode, you can do the steps that follow.
1. Long press the Menu button until mM.E.N.U appears on the display.
2. Release the Menu button, and C.A.L appears on the display.
3. Short press the No button several times until mM.O.d.E appears on the display.
4. Press the Yes button to enter the application mode.
5. Short press the No button several times until the wanted selection appears on the display.
6. Press the Yes button, and ON appears on the display. If you want to activate the application mode, short
press the Yes button. If you want to deactivate the application mode, short press the No button until OFF
appears on the display, then short press Yes button.
3.5.1 Weighing
This mode is the default factory setting, and it is used to determine the weight of the loads in the selected unit
of measure.
Entering the Mode and Starting to Weigh
To enter the weighing mode, you can do the steps that follow:
1. Long press the button Function Mode until wWEIGH appears on the display.
2. Put the container on the scale. Once the value is stable, you can see “*” on the display.
3. Press the button Tare to tare. If the scale performs well, you can see the value on the display is 0.
4. Put the load on the container and read the weight value of the load from the display. Once the value is
stable, you can see the “*” is on the display.
NOTE: You can check the value of the tare weight by long pressing the Tare button.
The Weighing configurations are defined below (Defaults in Bold).
Item
Available Settings
Comments
Weighing (
wWeIGH
)On, off To enable or disable Weighing
NOTE: You cannot disable the Weighing mode if you are in the mode currently.

EN-12 Courier 7000
3.5.2 Totalization
This application is used to accumulate the multiple weights manually or automatically. Statistical data (the
number of samples, the total weight, the average weight, the minimum weight, the maximum weight and the
difference in weight) is stored in memory for review and printing.
Application Settings
There are three totalization options:
Off (OFF): Disable the totalization function.
Manual (mMAN): Enable the totalization function manually with Function button.
Automatic (AutO): The scale performs the totalization function automatically.
NOTE: The option of Manual is the default setting.
Setting the Totalization Option:
1. Long press the Menu button until the mM.E.N.U appears on the display.
2. Release the Menu button, the C.A.L appears on the display.
3. Short press the No button several times until mM.O.d.Eappears on the display, then press the Yes button.
If you do it successfully, you can see the reset on the display.
4. Short press the No button several times until t0tal appears on the display, then press Yes button to
enter the sub menu.
5. Short press the No button several times to select the wanted totalization option. If the wanted option
appears on the display, you can press Yes button to confirm.
6. Press the Exit button to exit.
Entering the Mode
1. Long press the Mode button until tOtAL appears on the display.
2. Release the Mode button, and the CLr.ACC appears on the display.
•If you need to remove the stored totalization result of the last time, you can press the Yes button, and
then the scale performs the totalization function.
•If you need to reuse the stored totalization result of the last time, you can press the No button to
continue the totalization of the last time.
NOTE: If there is a container on the scale, the display shows CLr.PAN until the container is removed or
you press the Tare button to tare.
Totalization Method
Manual: The operator initiates the totalization with the Function button.
Automatic: The scale performs the totalization function automatically.
If the scale performs the totalization well, you can see the ∑is flashing. It will keep flashing until the weight is
removed and the platform is stable.
NOTE:
•Before you weigh the next load, you must remove the previous load from the scale.
•The scale only stores the stable value of the display.
•When Legal for Trade is turned ON, for NTEP models, gross and net weight cannot be added to the same
total. If the first weight is recorded in gross, the next one should be recorded in the same way. It is the
same for the net weight.
Checking the Totalization Result
When the scale is empty, you can press the Function button to check the result.
The result includes the number of samples, the total weight, the average weight, the minimum weight, the
maximum weight and the difference in weight (the maximum weight minus the minimum weight). The values
are displayed for 1 second each.
Totalization Rules
You will fail to do the totalization operation under the following conditions.
1. The current weight value is unstable.
2. The net weight of the load is smaller than 5d.
3. The overall totalized weight is larger than 999999.（The unit depends on your setting.）
4. The total number of totalizations exceeds 9999 times.

Courier 7000 EN-13
Printing Totalization Result and Format
1. Refer to the steps below, you can enable the Table on (tABLE) option in the menu.
a) Long press the Menu button until you see mM.E.N.U.
b) Release the Menu button and C.A.L. appears on the display.
c) Short press the No button several times until mM.O.d.E appears on the display.
d) Press the Yes button to enter the sub menu
e) Short press the No button several times until tABLE appears on the display, then press the Yes
button to enter the table setting options.
f) Short press the No button until ON on the screen.
g) Press the Yes button to confirm. And END appears on the display.
h) Press the Exit button to exit.
2. The Table option is enabled.
•In automatic totalization mode, the scale will automatically totalize the current weight when it performs
totalization successfully.
•In manual totalization mode, you can press the Function button to totalize the current weight and
print it accordingly.
3. The output for current weight will appear as the example below.
Example:
4. When the totalization is finished, you can print the totalization result by below two steps.
1. Remove the load from the scale.
2. Press the Function button, and the totalization result appears on the display.
3. Press the Print button to print the result.
Refer to the example below, you will see the output of the totalization result.
Example:
NOTE: The scale supports 32 characters, the first line is “-”. The colon is left aligned, and the Weights/Numbers
are right aligned.
3.5.3 Dynamic Weighing
This application is used to weigh an unstable load, such as a moving animal. Three different start/reset
operation types can be selected:
Off (OFF)
= Disable the mode.
Manual (mMAN)
= Averaging and resetting are initiated manually by pressing the FUNCTION key.
Semi-Automatic (SEmMI)
= Averaging is automatically initiated when the load weight is bigger than the start
weight; resetting is initiated by pressing the FUNCTION key.
Automatic (AUtO)
= Averaging is automatically initiated when the load weight is bigger than the start
weight; resetting is automatically initiated when the weight on the display is less
than 5d.
Display Hold
When the time is set to 0, the instrument will hold the displayed weight value on the display if that weight is
greater than 5 divisions.
NOTE: The minimum start weight is 5 divisions. If the scale does not operate, please check if the load is
greater than 5 divisions.
-------------------------
n: 5
Total: 100.000 g
Avg: 200.000 g
Min: 10.500 g
Max: 88.200 g
Diff: 78.300 g
1. 1000 g N
2. 2000 g N
3. 3000 g N
4. 1999 g N
5. 1000 g N
-------------------------

EN-14 Courier 7000
Entering the Dynamic Weighing Mode
To enter the dynamic weighing mode, you can do the steps that follow.
1. Long press the button Function Mode until dyNamM appears on the display.
2. Release the button Function Mode, and rEAdY appears on the display.
Starting Dynamic Weighing
1. Put the load on the scale.
•If the operation type is manual, you must press the Function button to start the averaging process.
•If the operation type is semi-automatic/automatic, the scale performs the averaging process
automatically when the load weight is bigger than the start weight.
NOTE:
•You can set the value of the start weight via this path: mM.E.N.U > mMOde > dyNamM > D.StArt. And the
correct range of the start weight value is 5d - capacity value.
•During the averaging period, the countdown timer decreases in one second increments. If the set
average time is 0s, the countdown timer is not displayed.
•The values on the display are averaged and held on the display when the countdown is completed.
2. Read the values on the display if the tilde (dynamic) symbol blinks on the display.
3. Reset the countdown timer:
•If the operation type is manual/semi-automatic, you can press the Function button to reset the
countdown timer when the countdown is running. The display shows rEAdY, and start to re-count.
•If the operation type is automatic, you can remove the load from the scale. And the average weight will
still be displayed until the duration time is over. Then the display shows rEAdY, and start to re-count.
NOTE:
•The rEADY display must be at zero gross or net value to reset the countdown timer.
Application Settings
The Dynamic Weighing Configurations are defined below (Defaults in Bold).
NOTE: The Dynamic mode cannot be disabled if the scale is in the Dynamic mode currently.
Item
Available Settings
Comments
Dynamic Mode
（
dyNAmM
）
Off (
OFF
) / on (
ON
)
Count down:
There is a countdown time.
Dynamic Operation
Type (
d.tyPE
)
Manul (
mMAN
)/
Semi-auto (
semMI
)/
Auto (
AUtO
)
Manual:
The averaging process is started and reset manually.
Semi-auto:
The averaging process is started automatically and reset
manually.
Auto:
The averaging process is started and reset automatically.
Start Weight
(D.StArt)
5d ~ Capacity Weight
Dynamic weighing will start when the load is bigger than the
start weight (for Semi-auto and Auto mode).
Duration Time
(d.tImME)
1 ~ 10s
It is the time for the display to remain the dynamic weighing
result after the load is removed.
Average Time
(
A.tImME
)
0 ~ 30s
Time in Seconds.
If the average time is 0, the first stable weight (more than or
equal to 5d) will be the result.

Courier 7000 EN-15
3.5.4 Weight Alert
This application is used to judge if the weight of the item is within the target limit. There are 2 limit values for
setting, the limit 1 is normally open as default.
Setting the Limit Values
1. Long press the Mode button until ALERt appears on the display.
2. Release the Mode button, the CLr.ALe appears on the display.
3. Press Yes button to remove the stored alert limit value, and LImM.1 appears on the display.
4. Press Yes button, 000000 is flashing on the display with the current unit.
5. To set the limit value 1, you can do the steps that follow:
a) Use the buttons NO and Back to set a number for the first digit.
b) Short press the Yes button to confirm the number and move to the next digit.
c) Repeat the steps a) and b) to set numbers for all the digits.
d) Press Yes button to confirm the value. If the value is not in the correct range, the NO appears on the
display. You must repeat the steps 3, 4 and 5 to set the value. If the value is in the correct range, the
LImM.2 appears on the display.
NOTE: If the LImM.2 is set to off, the LImM.2 will not appear on the display and the scale goes into
the weighing status directly.
6. Repeat steps 4 and 5 to set the limit value 2. If the value is not in the correct range, NO appears on the
display. If the value is in the correct range, the scale goes into the weighing status.
NOTE:
1. You can check the limit values by short pressing the Function key.
2. You can set either or both of the limit values. If the weight value of the load is larger than either limit value,
the segment text and the backlight blinks at the same time. Thus, the load is not acceptable.
If the weight value of the load is larger than both the limit values, the segment text blinks. Thus, the load is
not acceptable.
The maximum limit value is not larger than the capacity value.

EN-16 Courier 7000
4. MENU SETTINGS
The User Menu allows the users to customize the scale settings.
Note: Sub-menu for options (USB, Ethernet and Wireless in the table below) will be active when the specific
board is installed. Refer to the accessory manuals, you can find the additional setting information.
4.1 Menu Navigation
4.1.1 User Menu (In segments)
C.A.L
S.E.t.u.P
r.E.A.d
mM.O.d.E
U.N.I.t
r.s.2.3.2
P.r.i.n.t
2.S.E.r.I.A
P.r.i.n.t2
ZErO
SpaN
LIN
GEO
C.test
ENd
reset
C.Unit
CAP
Grad
P.ZerO
P.UNIt
A.tare
ENd
reset
Stable
ZErO
FIltEr
AZt
B.LIGHt
SCreeN
A.Off
P.SaUer
ENd
reset
wWeIGH
dyNamM
d.typE
d.start
d.tI
mM
E
A.tImME
tOtAL
tAble
ALERt
LimM.2
ENd
reset
g
kg
lb
oz
lb:oz
ENd
reset
BAud
PAritY
StOP
H.SHAKE
ALt.P
ALt.t
ALt.Z
ENd
reset
ASSIGN
DEmMAN
ON.StAb
ON.ACEP
INtEr
mMt.Con
OH.Con
SICS
NCI
8213
3835
SCP01
Stable
CONtNt
LAYOUt
ENd
reset
BAUd
PArItY
StOP
H.SHAKE
ALt.P
ALt.t
ALt.Z
ENd
reset
ASSIGN
DEmMAN
ON.StAb
ON.ACEP
INtEr
mMt.Con
OH.Con
SICS
NCI
8213
3835
SCP01
Stable
CONtNt
LAYOUt
ENd
U.S.B
P.r.i.n.t.U
E.t.H.N.E.t
P.r.i.n.t.E
wW.I.-B.t
P.r.i.n.t.H
L.o.c.k
E.n.d
reset
type
HID
CDC
ALt.P
ALt.t
ALt.Z
ENd
reset
ASSIGN
DEmMAN
ON.StAb
ON.ACEP
INtEr
mMt.Con
OH.Con
SICS
NCI
8213
3835
SCP01
Stable
CONtNt
LAYOUt
ENd
reset
IP.Addr
u.E.r.
ALt.P
ALt.t
ALt.Z
ENd
reset
ASSIGN
DEmMAN
ON.StAb
ON.ACEP
INtEr
mMt.Con
OH.Con
SICS
NCI
8213
3835
SCP01
Stable
CONtNt
LAYOUt
ENd
reset
type
IP.addr
d.NAmME
p.CODE
ALt.P
ALt.t
ALt.Z
ENd
reset
ASSIGN
DEmMAN
ON.StAb
ON.ACEP
INtEr
mMt.Con
OH.Con
SICS
NCI
8213
3835
SCP01
Stable
CONtNt
LAYOUt
ENd
reset
L.ALL
L.OFF
L.ZErO
L.Print
L.Unit
L.mModE
L.mMeNU
L.tArE
ENd
NOTE:
1. The following menus will not appear until the corresponding accessories are installed.
The 2.S.E.r.I.A and P.r.i.n.t2will not appear until option RS232 is installed.
The U.S.B will appear if you connect the scale into a PC with the USB type-C. And you can select the
HID or CDC type.
The P.r.i.n.t.U will appear if you select CDC type.
The E.t.H.N.E.t and P.r.i.n.t.E will appear if the ethernet board is installed.
The wW.I.-B.t and P.r.i.n.t.H will appear if the USB Host is installed.