OHAUS D31P75SD User manual

FR
D31P75SD Bench Scale
INSTRUCTION MANUAL
IT
PT
SV
DA
PL
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-1
1. SAFETY INFORMATION
Definition of Signal Warnings and Symbols
WARNING For a hazardous situation with mediumrisk, possibly resulting in injuries or death if not avoided.
CAUTION For a hazardous situation with low risk, resulting in damage to the device or the property or in loss
of data, or injuries if not avoided.
Attention For important information about the product.
Note For useful information about the product.
Warning Symbols
General hazard Electrical shock
Safety Precautions
CAUTION: Read all safety warnings before installing, making connections, or servicing this equipment.
Failure to comply with these warnings could result in personal injury and/or property damage. Retain all
instructions for future reference.
xVerify that the local AC power supply voltage is within the input voltage range printed on the equipment’s or AC adapter’s
ratingslabel.
xOnly connect the AC power cord or AC adapter to a compatible grounded socket.
xPosition the instrument such that the AC power cord or AC adapter can be easily disconnected fromthe socket.
xPosition the power cord so that it does not pose a potential obstacle or tripping hazard.
xOperate the equipment only under ambient conditions specified in the user instructions.
xDo not operate the equipment in hazardous or explosive environments.
xDisconnect the equipment from mains power before cleaning or servicing.
xService should only be performed by authorized personnel.
Intended Use
Use the instrument exclusively for weighing as described in the operating instructions. Any other type of use and operation
beyond the limits of technical specifications without written consent from OHAUS, is considered as not intended.
This instrument complies with current industry standards and the recognized safety regulations; however, it can constitute a
hazard in use.
If the instrument is not used according to these operating instructions, the intended protection of the instrument may be
compromised and OHAUS assumes no liability.
2. INSTALLATION
2.1 External Connections
RS232 Interface Cable to T31P
Connect the optional RS232 cable to the RS232 connector.
Pin
Connection
1
N/C
2
TXD
3
RXD
4
N/C
5
GND
6
N/C
7
N/C
8
N/C
9
N/C
AC Power Cord/Adapter Installation
Connect the AC mains/adapter power cord to the instrument's power input connector, and then connect the AC plug to a
suitable electrical outlet.
Attention: Only use an AC adapter specified by OHAUS
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-2
Rechargeable Battery Power
Allow the battery to charge for 12 hours before using the scale on battery power. The instrument can be operated during
charging, and the battery is protected against overcharging. For maximumoperating time, the battery should be charged
at room temperature.
3. OPERATION
3.1 Overview of Displayand Controls
Item
Description
1
Capacity label window
2
TARE Menu button
3
TARE symbol
4
FUNCTION Mode button
5
NET symbol
6
Pieces symbol
7
PRINT Units button
8
Calibration Mode symbol
9
Battery symbol (T31P)
10
ON/ZERO Off button
11
Center of Zero symbol
Control Functions
Button
On/Zero
Off
Yes
Print
Units
No
Function
Mode
Back
Tare
Menu
Exit
Primary Function
(S
hort Press)
ON/ZERO
T
urn indicator
on.
Z
ero the display.
PRINT
S
end the displaye
d
va
lue to the COM
po
rt.
FUNCTION
In
itiate the function
of
th
e current applicati
on
m
ode.
TARE
P
erform a tare operation.
Secondary
F
unction
(Long
Press)
Off
T
urn indicator
off.
Units
Ch
ange the weigh
ing
un
it.
Mode
A
llows changin
g the
appl
ication mode.
P
ress and hold allow
s
sc
rolling through
modes.
Menu
E
nter the menu.
V
iew the Audit Tra
il event
count
ers (extended pr
ess)
Menu Function
(S
hort Press)
Yes
A
ccept the curr
ent
m
enu or setting.
No
A
dvance to the ne
xt
m
enu or setting.
In
crement the
d
isplayed value.
Back
Go
back to the previ
ous
m
enu or setting.
Dec
rement the
d
isplayed value.
Exit
E
xit the menu.
A
bort the calibration in
p
rogress.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-3
3.2 Menu Structure
澳
4. MAINTENANCE.
4.1 Cleaning
WARNING: Electric Shock Hazard. Disconnect the equipment from the power supply before
cleaning. Make sure that no liquid enters the interior of the instrument.
Attention: Do not use solvents, harsh chemicals, ammonia or abrasive cleaning agents.
The exterior surfaces of the instrument may be cleaned with a cloth dampened with water and a mild detergent.
4.2 Troubleshooting
For technical issues contact an Authorized Ohaus Service Agent. Please visit our website www.ohaus.com to locate the
Ohaus office nearest you.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-4
5. TECHNICAL DATA
The technical data is valid under the following conditions:
Operating temperature range: -10
° C to 40 ° C
Relative humidity: Maximum relative humidity 80% for temperatures up to 31
° C decreasing linearly to 50% relative humidity at
40
° C.
Altitude: up to 2000m
Mains supply voltage fluctuations: up to
± 10% of the nominal voltage
Pollution degree: 2
Installation category: II
Specifications:
Model
D31P75SD
Capacity x Readability
75 kg x 0.02 kg
165 lb x 0.5 lb
Weighing Units
kg, lb
Modes
Weighing, Parts Counting
Stabilization time
Within 2 seconds
Zero range
To capacity by subtraction
Maximum Overload
150%
Battery Operating Time
70-hour typical life
Operating Temperature
Range
-10°C to 40°C/14°F to 104°F
Cable Length
1.8m / 72” (uncoiled)
Display
1 in./2.5 cm digit height, 6-digit, 7-segment
1.5 in./3.8 cm high x 4.9 in./12.5 cm wide backlit LCD
Scale Base Size
316mm L x 280mm W x 45mm H /
12.4” L x 11” W x 1.77” H
Indicator Size
210mm L x 168mm W x 71mm H / 8.2” L x 6.5” W x 2.8” H
AC Adapter
9-12 Volt DC, 500mA
Net Weight
4.7 kg / 10.3 lb
Shipping Weight
8 kg / 17.6 lb
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

3000 SER ES ND CATORS
EN 6
INSTRUCTION MANUAL
For more detailed information about the T31P indicator,
please refer to the product instruction manual. The
instruction manual can be obtained either by scanning
the QR code or by going to the product page and from
there download it. Go to www.ohaus.com to register
your product's warranty.
Product Page: http://www.ohaus.com/
QR Code:
*30448502*
P/N 30448502 A © 2018 Ohaus Corporation, all rights
reserved.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]