OHAUS ranger 7000 User manual

Quick Start Guide Ranger™7000
Ohaus Corporation www.ohaus.com iii Ranger 7000 Quick Start Guide
Safety Precautions
Caution: Read all safety warnings before installing, making connections, or servicing this
equipment. Failure to comply with these warnings could result in personal injury and/or
property damage. Retain all instructions for future reference.
Verify that the input voltage range printed on the data label and the plug type matches the local AC
power to be used.
Only connect models supplied with a grounded power cord to a compatible grounded power
receptacle.
Do not position the scale such that it is difficult to disconnect the power cord from the power
receptacle.
Make sure that the power cord does not pose a potential obstacle or tripping hazard.
This scale is for indoor use only.
Use the scale in dry locations only.
Do not drop loads on the pan.
Use only approved accessories and peripherals.
Operate the equipment only under ambient conditions specified in these instructions.
Disconnect the equipment from the power supply when cleaning.
Do not operate the equipment in hazardous or unstable environments.
Service should only be performed by authorized personnel.
Installation
Unpacking
Carefully remove your Ranger 7000 scale and each of its components from the package. The included
components vary depending on the scale model (see table below). Save the packaging to ensure safe storage
and transport.
Included Component
Photo
R71MHD3
R71MHD6
R71MD3
R71MD6
R71MHD15
R71MHD35
R71MD15
R71MD35
R71MD60
Terminal
X
X
X
X
Weighing
Base
X
X
X
X
Weighing
Platform
200 x 200 mm
X
Weighing
Platform
240 x 240 mm
X
Weighing
Platform
311 x 371 mm
X
X
Wind Shield
X
Compact
Disc
Instruction
Manual
X
X
X
X

Ranger™7000 Quick Start Guide
Ranger 7000 Quick Start Guide ii Ohaus Corporation www.ohaus.com
Installing Components
Refer to the illustrations and instructions below to identify and assemble your Ranger 7000 scale with its
components. All components must be assembled before using the scale.
Terminal Setup
When the Ranger 7000 is delivered, the Terminal is already attached (docked) to the Base. No additional
setup is necessary. Refer to the illustrations and instructions below to identify and assemble your Ranger
7000 Scale.
Note: The Terminal is identical for all Ranger 7000 Scale models.
Installing the Wind Ring, Weighing Platform
1. Place the Wind Ring in position
(R71MHD3, R71MHD6).
2. Place the platform onto the
spider.
Selecting the Location
Avoid excessive vibrations, heat sources, air current, or rapid temperature changes. Allow sufficient
space.
Note: Interface cables connect to the terminal. The terminal can be detached and mounted on a wall
or positioned on a table separate from the scale.
Connecting Power and Turning ON the Scale
The Ranger 7000 comes with an AC power cord. Connect the power cord to a suitable grounded electrical
outlet and press the ON button on the side of the base (see figure below).
Attention: Allow equipment to warm up for 60 minutes for optimal weighing performance.
Power ON Button

Quick Start Guide Ranger™7000
Ohaus Corporation www.ohaus.com iii Ranger 7000 Quick Start Guide
Controls
Button
Action
Enter/Exit the library menu
Switch between available application modes
Send the measurement data to available communications ports according to current
settings.
Display information about Application Mode, Library, User and Menu
Enter/Exit the User menu
Switch the main weighing unit between the available units
Short Press: Input ‘2’-‘9’
To Enter ‘A’ press 2 times. For lower case ‘Z’, press 5 times.
Short Press: Input ‘0’
Long Press: Go to User Login screen
Short Press: Input ‘1’
Long Press: Switch platform between scale 1 and scale 2
Short Press: Clear character/string when editing string
If no input is active, clear the current active library
When there is no value added, pressing this button will switch the value
sign between positive and negative.
Short Press: Input ‘.’, space, ‘_’
To Enter ‘_’ press 3 times.
Perform Zero operation
Perform Tare operation
When entering the value first and then pressing this button the number input will be set to
preset Tare value.

Ranger™7000 Quick Start Guide
Ranger 7000 Quick Start Guide iv Ohaus Corporation www.ohaus.com
Applications
The scale can be configured to operate in various Application modes, see the Instruction Manual for
information on how to activate/deactivate each application mode.
Press to select an activated application. The current application will be shown in the upper left corner
of the home screen.
The Ranger 7000 incorporates the following Applications
Weighing
Counting
Check
Formulation
Percent
Weighing
Filling
Dynamic
(Animal)
Density
Determination
Differential
Note: Before using any application, be sure the scale has been leveled and calibrated.
This product conforms to the EMC Directive 2004/108/EC, the Low Voltage Directive
2006/95/EC and the Non-automatic Weighing Instruments Directive 2009/23/EC.
The complete Declaration of Conformity is available online at
europe.ohaus.com/europe/en/home/support/compliance.aspx.
Disposal
In conformance with the European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE) this device may not be disposed of in domestic waste. This also applies to
countries outside the EU, per their specific requirements.
Ohaus® and Ranger® are either registered trademarks or trademarks of Ohaus Corporation in the United
States and/or other countries.
Ohaus Corporation
7 Campus Drive
Suite 310
Parsippany, NJ 07054 USA
Tel: [phone]
Fax: [phone]
With offices worldwide
www.ohaus.com
*30232802*
P/N 30232802A © 2014 Ohaus Corporation, all rights reserved.