OHAUS Valor V31XH202 User manual

Valor™3000 Series
Instruction Manual
Serie Valor™3000
Manual de instrucciones
Valor™série 3000
Manuel d’instructions
Valor™3000-Serie
Bedienungsanleitung
Serie Valor™3000
Manuale di istruzioni
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

Valor 3000 Series Scales EN-1
1. INTRODUCTION
This manual contains installation, operation and maintenance instructions for the
ValorTM 3000 Series Scales. Please read the manual completely before using the
scale.
1.1 Safety Precautions
Please follow these safety precautions:
• Verify that the AC Adapter input voltage matches the local AC power supply.
• Use the scale only in dry locations.
• Do not operate the scale in hostile environments.
• Do not drop loads on the platform.
• Do not place the scale upside down on the pan.
• Service should be performed only by authorized personnel.
1.2. Controls
Figure 1-1. Controls.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-2 Valor 3000 Series Scales
TABLE 1-1. CONTROL FUNCTIONS.
Button
Functions
O/T On/Off
Short Press: (when off) Turns scale on
(when on) Sets display to zero
Tares weight of item on pan
Long Press:
Turns the scale off
MODE/UNIT
Menu
Short Press Steps through active units and modes
Long Press: Enters menu
Short Press (Menu)
“No” (toggles through available settings)
ENTER Cal
Short Press: Stores 100% reference in % mode
Stores reference sample in SG mode
Long Press Initiates span calibration process
Short Press(Menu)
Yes” (selects/accepts displayed setting)
2. INSTALLATION
2.1 Package Contents
• Scale
• Pan
• Power Adapter
• Instruction Manual
• Warranty Card
2.2. Location
Use the scale on a firm, steady surface. Avoid locations with excessive air current,
vibrations, heat sources, or rapid temperature changes. Adjust the leveling feet so
the bubble is centered in the circle.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

Valor 3000 Series Scales EN-3
Figure 2-1. Leveling the Scale.
2.3. Transport lock
Open the battery cover. Move the transport lock switch to “Unlock” position. Install
4 C (LR14) batteries, if desired. Reinstall the battery cover
Figure 2-2. Battery Installation.
2.4 Power
The AC adapter (included) may be used to power the scale when battery power is
not available. Remove the rubber seal in the bottom. Store it in the location
provided. Connect the AC adaptor plug to the input jack.
NOTE: To prevent water ingress during cleaning, insert back rubber seal into the
input jack recess.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EN-4 Valor 3000 Series Scales
Figure 2-3. Power Connection and Sealing.
2.5 Initial Calibration
When the scale is first installed, it should be calibrated to ensure accurate weighing
results.
Press and hold the ENTER/Cal button until CAL is displayed. When the button is
again pressed and released, the display shows -C- while zero reading is stored.
Next, the display shows the calibration weight value in grams. Place the specified
calibration weight (sold separately) on the pan. See Table 2-1 for appropriate
weights. The display shows -C- while the reading is stored. The display returns to
the previous application mode and scale is ready for use.
TABLE 2-1. CALIBRATION WEIGHTS.
MODELS
V31XH202
V31XH402
V31XH2
V31XH4
V31X501
Calibration
Weights
200g 400 g 2 kg 4 kg 500 g
MODELS
V31X3
V31X6
V31XW301
V31XW3 / V31X3N
V31XW6 / V31X6N
Calibration
Weights
3 kg 6 kg 300 g 3 kg 6 kg
3. OPERATION
3.1 Weighing Mode
Use this mode to measure the weight of a sample in the selected unit of measure.
1. Press MODE/UNIT/Menu until the desired unit icon is displayed.
2. Put an empty container on the pan, then press O/T/On/Off to tare the container
weight.
3. Add material to the container. The display shows the weight of the material.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]