Ohio Steel 34601 User manual

2
25, 25N
1
9
13
14
16
12
28K
15
28K
17
19
18
21
19
32
28
2575 FERRIS ROAD
Model No. 34601
17 Cu. Ft. Dump Cart
USER GUIDE AND PARTS LIST
17 CUBIC FOOT LAWN CA T
34601
COLUMBUS, OH 43224-2597
EPAI PA TS LIST
346 1-REV-A 12_ 4
THIS EQUIPMENT.
BEFORE USING
AND INSTRUCTIONS
ALL SAFETY RULES
CAUTION:
READ AND FOLLOW
OHIO STEEL INDUSTRIES
When ordering repair parts always give the following information.
PRODUCT NAME, MODEL NUMBER, PART NUMBER and PART DESCRIPTION.
* Denotes standard hardware items that can be purchased locally.
REF. NO. PART NO. AMT. DESCRIPT ION REF. NO. PART NO. AMT. DESCRI PT ION
1 17-1 1 CART BODY 18 17-18 2 SPACER
2 17-2 1 TAIL GATE 19 17-19 4 *AXLE W ASHER
9A 17-9A 1 FRONT SUPPORT 21 17-21 2 TIRE
11 17-11 1 AXLE HOLDER 25 17-25 16 *BOLT 5/16 X 3/4 PAN
12 17-12A 1 HITCH ASSEMBLY 25N 17-25N 16 *HEX NUT 5/16
13 17-13A 1 LATCH POST 28 17-28 1 *BOLT 3/8 X 3/4 HEX
14 17-14A 1 *LATCH BOLT 28K 17-28K 1 *KEPS NUT 3/8
15 17-15A 1 LATCH SPRING 32 17-32 2 *COTTER PIN 1/8 X 1 1/2"
16 17-16A 1 HITCH BRACKET 33 17-33 1 USER GUIDE
17
17-17
1
AXLE

and hitch and center.
Add washer, spacer, wheel and•
another washer in that order
to each end of the axle.
Insert cotter pins •
through holes in
axle and lock in place
by spreading ends.
5/16 keps nuts to attach undercarrige as shown.
• Use twelve 5/16 x 3/4 pan head bolts and
pan head bolts and 5/16 keps nuts.
• Attach the front support using four 5/16 x 3/4
the front support.
• Position Cart to add the undercarriage and
• cordless drill
• pliers
• large blade screw driver
• 1/2 wrench
TOOLS REQUIRED
ASSEMBLY - SEE FIGURE 1.
SAFETY RULES
DO NOT CARRY PASSENGERS IN THE CART.•
• LOAD CAPACITY IS 1500 POUNDS
• BECAREFUL ON STEEP GRADES.
• LODS OR OVER ROUGH TERRAIN.
• USE LOW SPEED - 5MPH-WHEN PULLING HEAVY
•
and corrosion.
• Keep cart clean and dry to prevent rust
• Grease wheels regularly.
14 p.s.i. is recommended.
• Check tire pressure regularly.
MAINTENANCE
DO NOT TOW THIS CART ON PUBLIC ROADS.
ASSEMBLY - SEE FIGURE 2.
Slide axle through the axle holder •
OPERATION
With cart attached to tractor, remove tailgate,•
and then pull back on latch bar. Cart body will
tilt backwards, dumping contents. Once empty,
replace tail gate, then pull cart body back down
until it latches.
Follow all operating instructions in •
tractors user manual.
18
Figure 2.
19
21
19
17
12A
32
•
Figure 3.
ASSEMBLY - SEE FIGURE 3.
Turn cart upright on wheels.•
Slide tail gate into position.•
Assembly is complete.
2
25
Figure 1.
11
9
25N