Ohio Steel 3460HATV User manual

READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS BEFORE USING THIS EQUIPMENT
3460HATV
20 cu ft WELDED STEEL ATV CART
3190460 - REV C07/15

Read and understand all safety rules and operating instructions before using this
ATV/UTV attachment.
Follow all safety rules and operating instructions provided by your vehicle's
manufacturer when using attachment.
Never allow children or untrained persons to operate vehicle or attachment.
Do not exceed the vehicle manufacturer's towed weight limit.
Reduce vehicle speed and allow extra stopping distance when towing heavy
loads.
Reduce vehicle speed and towed weight when operating on slopes.
Operate up and down slopes, never across the face of slopes.
Do not carry passengers on vehicle or attachment.
Avoid sudden turns or maneuvers.
Do not tow attachment on public roadways.
Do not remove warning decals from product.
Check product for worn, loose, or damaged parts before each use. If any damage
is present, repair the product before using.
Check product for loose or missing fasteners before each use. Tighten or replace
fasteners as needed before using.
Do not exceed vehicle speed of 20 miles per hour when towing Dump Cart.
Do not exceed Dump Cart rated weight capacity of 1500 pounds.
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
1
Safety Rules

12 (x2)
11 (x2)
9 (x1)
TOOLS REQUIRED FOR ASSEMBLY:
1/2" Wrench and Socket •
9/16" Wrench and Socket •
1 (x1)
7/16" Wrench and Socket •
Needle-Nose Pliers •
Grease Gun •
2 (x1)
5 (x4)
8 (x1)
6 (x1)
15 (x1)
4 (x1)
7 (x1) 3 (x1)
16 (x2)
10 (x1) 14 (x1)
13 (x2)
20 (x2)
17 (x1) 18 (x1)
19 (x19) 21 (x1)
2
Carton Contents

4
3
18
17
9
5
21
19
2
821
21
1
Attach front support and backing plate to body securely with hardware as
shown.
Attach axle holder plates to body loosely with hardware as shown.
Attach latch and hitch bracket to drawbar with hardware as shown.
Secure latch spring between latch and drawbar post.
3
Assembly Instructions
1
3
2

15
12
11
16
13
Insert axle into undercarriage halfway as shown.
Slide axle completely through undercarriage; be sure to catch the drawbar
when sliding the axle. Align drawbar with the front support and press down
firmly to latch.
Attach wheels to axle with spacers and washers, secure with cotter
pins as shown.
4
Assembly Instructions
4
6
5

6
20
7
21
10
14
Attach tailgate to body as shown. No hardware is required, tailgate should
move freely up or down.
Attach hitch bracket to drawbar with hardware as shown.
Install hitch pin and hairpin to secure to attachment vehicle.
* BE SURE TO
TIGHTEN ALL
HARDWARE
AT THIS TIME
5
Assembly Instructions
7
9
8

Periodic Maintenance:
Tighten fasteners as needed before each use •
Check tire pressure before each use •
Grease wheels annually •
Before Using Dump Cart:
Apply lithium grease to wheels using grease gun until grease can be seen 1.
squeezing out from both sides of the wheel.
Check tire pressure and inflate to 24 psi if needed. 2.
Read all Safety Rules found on page 1. 3.
How to Use Dump Cart:
Attach Dump Cart to your ATV or UTV. 4.
Do not exceed 1500 pounds when loading material into the cart body. 5.
Distribute the weight of the load as evenly as possible in the cart body for 6.
best handling.
When hauling heavy loads, verify that your vehicle has adequate towing and 7.
braking capacity.
Do not exceed 20 miles per hour when towing Dump Cart. 8.
How to Empty Dump Cart:
Pull hand lever up to release the latch mechanism. 9.
Lower the body and guide the latch into the drawbar and relatch. 10.
6
Operating Instructions

If this product fails due to a defect in material or workmanship within TWO
YEARS from the date of purchase, we will at our option repair or replace it free of
charge. This warranty excludes tires and wheels, which are expendable and
become worn during normal use.
This warranty does not cover:
Repairs necessary because of operator abuse or negligence. •
Equipment used for commercial or rental purposes. •
Paint that is worn or faded due to normal use or exposure. •
To arrange for product repair call 1-800-652-2321, or return this product to place
of purchase for replacement.
This warranty gives you specific legal rights, and you may also have other rights
which may vary from state to state. This warranty applies only while this product
is in use in the United States.
In the space below record the purchase date of your Dump Cart.
Model Number 3460HATV
Purchase Date
Keep this Owner's Manual and your receipt in a safe place for future reference.
After the two year warranty period all replacement parts may be ordered by
calling 1-800-652-2321 .
When ordering replacement parts, always give the following information:
Product 20 cu ft WELDED STEEL ATV CART •
Model Number 3460HATV •
Part Number •
Part Description •
8
Warranty

6
1
8
19
5
21
12
15 11
16 13
4
3
18
9
2
2117
20
7
10
14 21
22
23
24
ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 419003 1
2 419091 1
3 419291 ARM, LATCH 1
4 419102 1
5 419271 4
6 401042 1
7 419121 1
8 419281 1
9 300132
SPRING,
LATCH
1
10 6000533 PIN, HITCH 1
11 3001211 2
12 300076
WASHER, 1"
SAE
2
13 300081
COTTER PIN,
1/8" X 1-1/2"
2
14 300084
HAIRPIN
COTTER
1
15 300003 1
16 6000727 2
17 300065
1/4" -20
LOCK NUT
1
18 6000420
1/4" -20 X
3/4" BOLT
1
19 300052
HEX BOLT,
3/8-16 X 3/4"
2
20 3000511
HEX BOLT,
3/8-16 X 1"
1
21 3000618
NYLON
INSERT
LOCKNUT,
3/8-16 UNC
3
34 6000814 - 1
25 6000816 - 1
9
Repair Parts
REPLACEMENT PARTS ORDERING OHIO STEEL INDUSTRIES 1-800-652-2321

10
Notes

www.OHIOSTEEL.com
[phone]
Designed And Tested In Columbus, Ohio
MODEL # 3460HATV
2575 Ferris Road Columbus, OH 43224
[phone]
Manufactured In The U.S.A. From Domestic
And Imported Components