Oki CX3535MFP Original instructions

1
CX3535, CX4545
Safety Information, 120-Volt Models. . . . . . . . . . . . . . . . . . . . . . . .2
Informations de sécurité, de garantie, et de réglementation . . . .32
United States and Canada, Etats-Unis et
Canada, Estados Unidos y Canadá
English
Safety Information . . . . . . . . . . . . . . . . . . . . . . 2
Warranty Information . . . . . . . . . . . . . . . . . . . . 4
Service and Support . . . . . . . . . . . . . . . . . . . . . 5
Regulatory Information . . . . . . . . . . . . . . . . . . . 6
Material Safety Data Sheet (MSDS) . . . . . . . . . . 8
Français
Informations sur la sécurité . . . . . . . . . . . . . . . 32
Information sur la garantie . . . . . . . . . . . . . . . 34
Service et soutien. . . . . . . . . . . . . . . . . . . . . . 36
Informations réglementaires . . . . . . . . . . . . . . 37
Fiche technique santé-sécurité (MSDS) . . . . . . . 39

2 - English
Safety, Warranty and Regulatory Information
Safety Information,
120-Volt Models
Your OKI product has been carefully designed to give you
years of safe, reliable performance. As with all electrical
equipment, there are a few basic precautions you should
take to avoid hurting yourself or damaging the product.
• Carefully read the provided setup and operating
instructions.
• Save all provided documentation for future reference.
• Read and follow all warning and instruction labels on the
product itself.
• Unplug the product before you clean it. Use only a damp
cloth; do not use liquid or aerosol cleaners.
• Place your product on a firm, solid surface. If you put it on
something unsteady, it may fall and be damaged. If you
place it on a soft surface, such as a rug, sofa, or cushion,
the vents may be blocked, causing the product to
overheat.
• Protect your product from overheating. Make sure no
obstructions block the openings of the product. Do not put
the product on or near a heat source (such as a radiator or
heat register). Keep the product out of direct sunlight.
• Always use this product in a well ventilated area. Allow
enough room around the product for adequate ventilation
and easy access to the paper trays. If you put the product
in any kind of enclosure, make sure the enclosure is well
ventilated.
• Do not use your product near water. Do not spill liquid of
any kind into it.
• Be certain that your power source matches the rating
listed on the back of the product. If you are not sure,
check with your dealer or with your local power company.
• Do not connect this product to an uninterruptible power
supply (UPS). For further information please contact Oki
Data at 1-800-OKI-DATA.
• Your product has a grounded, three-prong plug as a safety
feature. This plug only fits into a grounded outlet. If the
plug does not fit, the outlet may be an older,
non-grounded type. Contact an electrician to have the
outlet replaced. Do not use an adapter to defeat the
grounding.
• Install the product near an easily accessed power outlet.
• Avoid damaging the power cord. Do not put anything on it
or place it where it will be walked on. If the cord becomes
damaged or frayed, replace it immediately.
• If you are using an extension cord or power strip with the
product, make sure that the total of the amperes required
by all the equipment on the extension is less than the
extension’s rating. The total ratings of all equipment
plugged into the outlet should not exceed 15 amperes.
• Important! A telephone cable using 26 AWG wire or larger
must be used with this equipment.
• Do not poke anything into the ventilation slots of the
product. You could get an electrical shock or cause
hazardous electrical arcing, which could cause a fire.
• Aside from the routine maintenance described in the
documentation, do not try to service the product yourself.
Removing the cover may expose you to shocks or other
hazards.
• Do not make any adjustments other than those outlined in
the documentation. You may cause damage that will
require extensive repair work. The provided
documentation explains how to get your product serviced
by qualified Oki Data technicians.
If anything happens that indicates that your product is not
working properly or has been damaged, unplug it
immediately and follow the procedures in the provided
documentation for having your product serviced.
Here are some of the things to look for.
• The power cord or plug is frayed or damaged.
• Liquid has been spilled into the product, or the product has
been exposed to water.
• The product has been dropped, or the cabinet is damaged.
• The product does not function normally when you are
following the operating instructions.
Additional Safety Informaton for
Telecommunications Equipment
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the
following:
• Do not use this product near water—for example, near a
bathtub, washbowl, kitchen sink or laundry tub—in a wet
basement, or near a swimming pool.
• Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of
electric shock from lightning.
• Do not use the telephone to report a gas leak in the
vicinity of the leak.
• Use only the power cord and batteries indicated in this
manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS.

3 - English
Safety Information,
220/240-Volt Models
This product has been carefully designed to give years of safe,
reliable performance. As with all electrical equipment, however,
there are a few basic precautions that should be taken to avoid
injury or damage:
Ensure this and all other documentation is both read carefully
and retained for future reference.
Ensure all warning and instruction labels on the product are
read, understood and followed in order to prevent any risk of
injury.
This product may be heavy. Please check the weight of the
product and take all necessary precautions to prevent the risk
of personal injury.
The product must be placed on a flat solid surface strong
enough to support its weight to prevent any risk of injury.
Ensure that there is adequate ventilation all around the
product to prevent overheating and any risk of fire.
Keep the product away from direct heat sources such as
radiators and out of direct sunlight to prevent any risk of
overheating.
The power supply required for this product is 220-240 VAC,
50/60 Hz. (For any DC powered product, the figures are 9.6-
31.2VDC, 4-1.8A.) Refer to your product's rating label on the
machine for full power rating details. Ensure that you have a
suitable power supply before connecting the product. If in
doubt contact your dealer or check with your local power
provider.
Ensure both the product and mains power switches are in the
OFF position before connecting the AC power cable.
Do not connect or disconnect the power plug with a wet hand
as this may cause electric shock.
Always hold the power plug to connect/disconnect the power
cable to/from the mains socket. Unplugging by pulling on the
cable can cause fraying and may lead to fire or electric shock.
This product has an earthed plug as a safety feature and will
only connect to an earthed socket. Do not attempt to defeat
the earthing or there is a risk of fire or shock.
If using an extension cable or power strip ensure that the total
current rating (amperes) of all connected equipment is less
than the maximum rating of the extension cable, power strip
or wall outlet. If the product is already supplied with a fitted
power strip then no additional power strip or extension cable
should be used to connect to the mains wall outlet. Otherwise,
fire or shock may occur.
Ensure the power cable is routed so as not to be damaged or
cause a trip hazard. If the cable becomes frayed or damaged
replace it immediately to prevent any risk of shock.
Do not twist, constrict or knot the power cable as this can
cause overheating which may lead to fire or electric shock.
Ensure the power socket to which the product is connected is
easily accessible at all times and not obstructed.
Use only the power cable supplied. Using a power cable not
intended for this product may lead to fire or electric shock.
To avoid risk of fire and electric shock, do not use the power
cable supplied with this product for any other electrical
equipment.
If you do not connect the power cord or any other cables only
as directed in the User's Guide, this may result in a fire.
It is recommended that the machine is switched off prior to
opening covers; otherwise there is a risk of electric shock.
When the product cover is open, do not touch the fuser unit or
print head as you may receive burns. Allow it to cool before
touching.
If the product casing gets extremely hot or smoke, unusual
smells or abnormal noises are emitted from the product, there
is a risk of fire. Unplug the mains connector and contact your
dealer.
If the product has been knocked over or damaged, there is a
risk of electric shock, fire and/or injury. Unplug the mains
connector and contact your dealer.
If any liquid (for example water) is allowed to enter the
product, there is a risk of fire. Unplug the mains connector
and contact your dealer.
Do not place containers containing liquid on the product as
electric shock, fire and/or injuries may occur.
If any foreign objects (for example clips) are allowed to enter
the product, there is a risk of electric shock, fire and/or injury.
Unplug the mains connector before removing the object.
Do not introduce foreign objects into the ventilation holes or
operate this product with any covers open or doors removed as
electric shock, fire and/or injuries may occur.
Do not use an extremely flammable spray near the product as
the product contains high temperature parts that may cause a
fire.
Switch the product off before cleaning to prevent any risk of
injury. Clean using a damp cloth. Do not use liquid or aerosol
cleaners.
Ensure loose clothing and hair is kept clear of moving parts
when the product is in operation to prevent possible risk of
injury.
Do not carry out any operations on the product that are not
specified in the User's Guide. This may result in electric shock,
fire and/or injury.
Do not touch the battery if one is fitted to the product. There
is a risk of explosion if the battery is replaced by an incorrect
type. The product battery should not require replacement
during the life of the product.
Do not throw toner cartridges or image drum cartridges into a
fire as you may receive burns from a dust explosion.
After installing additional memory, hard disk drive, or any
other internally fitted option, any covers removed or doors
opened must be closed or replaced and secured to prevent
risk of fire.
The acoustic noise of this product is less than 70 dB (A) as
measured in accordance with EN ISO 7779.
The operating condition range for your product is: 10 to 32°C
and 20 to 80% RH. Operation of the product outside this
range could result in damage to the product.
If a scanner, finisher etc. is fitted, exercise care when moving
these items so as to avoid risk of entrapment or personal
injury.
If the product is installed on a cabinet or high capacity feeder,
ensure wheel locks are applied once placed in final position for
use, to prevent risk of movement or injury.

4 - English
Limited Warranty, US and Canada
U.S. and Canada only
Oki Data Americas, Inc. (Oki Data) warrants this CX3535/
4545 (hereinafter "the Product") to be free from defects in
material and workmanship and will remedy any such defect
according to the terms of this
Limited Warranty .
Oki Data will repair (or at its option, replace) at no charge,
any defective component(s) of the Product for 90 days from
the date of purchase. This Limited Warranty extends to the
original purchaser only. This Limited Warranty does not
extend to consumable items.
On-Site Repair
Note: On-Site Repair is available in the United States
and Canada only. On-Site Repair does not
include the replacement or repair of product
consumables or supplies.
Oki Data will, for a period of 90 days from the date of
original purchase, repair or replace (at Oki Data's option)
on-site at the original purchaser's facility and without
charge, any defective component(s) of the product,
provided that the warranty service is performed by an Oki
Data authorized service provider.
Oki Data reserves the right to use new and/or refurbished
parts in the warranty repair process. If the product or a
component of the product is being replaced, the
replacement product or component will be warranted for
thirty (30) days or the remaining warranty period of the
replaced product, whichever is longer.
As a condition of this
Limited Warranty , requests for
On-Site Repair must include the name and phone number
of a fully competent and responsible adult with the
authority to consent to the entry of the servicing
technician to the premises where the product is located,
and who will remain with the servicing technician while
the service work is performed. Any and all dangerous
conditions must be removed from the site prior to and
throughout the time a service technician is present. The
service technician may refrain from entering the premises
or continuing to provide services at any site, if in the
servicing technician's reasonable judgement the site
poses a risk of physical harm or danger. If warranty
services cannot be performed or completed due to any of
the foregoing reasons the On-Site service option is null
and void and the product must be returned to an
authorized Oki Data service location for warranty repair
service.
To make request or claim for service under this
Limited
Warranty
contact your local Oki Data authorized service
center or Oki Data at 1-800-OKI-DATA (1-800-654-3282).
A written receipt for the product, showing the date of
purchase, dealer’s name, and both the model and serial
numbers of this product must accompany any request or
claim for work to be performed under this Limited Warranty .
This Limited Warranty shall not apply if the product has
been damaged due to abuse, misuse, misapplication,
accident, or as a result of service or modification by any
other than an authorized Oki Data service center.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE.
NO WARRANTIES WHETHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, SHALL EXTEND BEYOND THE
RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
OKI DATA SHALL NOT BE RESPONSIBLE OR LIABLE
FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSS ARISING
FROM THE USE OF THIS PRODUCT.
Some states do not
allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion may not
apply to you.
Except for the warranty coverage referenced above,
NEITHER OKI DATA NOR ITS SUPPLIERS SHALL HAVE
ANY LIABILITY OR OBLIGATION TO CUSTOMER OR
ANY OTHER PERSON FOR ANY CLAIM, LOSS, DAMAGE,
OR EXPENSE CAUSED IN WHOLE OR IN PART,
DIRECTLY OR INDIRECTLY, BY THE INADEQUACY OF
ANY PRODUCTS FOR ANY PURPOSE, BY ANY
DEFICIENCY OR DEFECT IN ANY PRODUCTS
(WHETHER OR NOT COVERED BY ANY WARRANTY), BY
THE USE OR PERFORMANCE OF ANY PRODUCTS OR BY
ANY FAILURE OR DELAY IN OKI DATA’S
PERFORMANCE HEREUNDER, OR FOR ANY SPECIAL,
DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGE, HOWEVER CAUSED INCLUDING, WITHOUT
LIMITATION, PERSONAL INJURY OR LOSS OF
BUSINESS OR PROFIT, WHETHER OR NOT CUSTOMER
SHALL HAVE INFORMED OKI DATA OF THE
POSSIBILITY OR LIKELIHOOD OF ANY SUCH
DAMAGES.
Customer’s exclusive remedy under these warranties is
limited, at OKI Data’s election, to any one of (a) refund of
customer’s purchase price, (b) repair by OKI Data or the
manufacturer of any products found to be defective, or (c)
replacement of any such product.
Except as specifically set forth in this paragraph,
THERE
ARE NO REPRESENTATIONS OR WARRANTIES OF
ANY KIND BY OKI DATA OR ANY AGENT OR
EMPLOYEE THEREOF, EXPRESS OR IMPLIED, AS TO
THE CONDITION OR PERFORMANCE OF ANY
PRODUCTS, THEIR MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE, OR OTHERWISE.
Additional information on obtaining service under this
Limited Warranty in the U.S. and Canada is available by
contacting the dealer from whom the product was
purchased, by contacting Oki Data directly at
1-800-654-3282 (1-800-OKI-DATA) or by contacting one of

5 - English
the service locations listed below. Spanish Only: call
1-856-222-5276. Canada Only: call 1-905-238-4275.
This Limited Warranty applies to this product. However, the
procedure for obtaining service may vary outside the
continental United States. Contact your Oki Data dealer for
such warranty service information.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Service and Support,
US and Canada
U.S. and Canada only
Oki Data is firmly committed to the satisfaction of our
customers. If you have a problem that your customer
documentation cannot solve, contact the listed sources for
service or support.
Oki Data Authorized Service Providers
For the most comprehensive, up-to-date listing of Oki Data
authorized Service Centers in the United States and Canada:
• In the U.S. go to www.okiprintingsolutions.com.
• In Canada and the U.S., call 1-800-654-3282
(1-800-OKI-DATA).
Oki Data Contact Locations
Sales and Service Dealers
Consult the store location where you purchased your
machine, or contact Oki Data for the location of the nearest
Authorized Oki Data Service Dealer.
• Prices and minimum charges may vary.
• Proof of purchase is required for warranty work. Be sure to
retain your purchase documents.
Automated Services for Your Convenience
Quick Referrals
To get quick referrals for a local Sales and Service
Authorized Reseller, including products, parts and
consumable supplies, contact us at any time:
• 1-800-654-3282 (1-800-OKI-DATA)
• www.okiprintingsolutions.com
Your Own Personal Solutions Center
You can easily create your own Personal Solutions Center
providing up-to-the-minute Oki information specifically for
your product, including:
•Productnews
• Manuals
• Drivers and utilities
• Material Safety Data Sheets
• Searchable knowledge base
•andmuchmore!
Just take a few minutes setting it up once, then you can
check your Personal Solutions Center for the latest
information at any time.
Get started today by visiting http://MY.OKIDATA.com.
Customer Support Representatives
1-800-654-3282 (1-800-OKI-DATA)
Customer Support Representatives are available 24 hours a
day, 7 days a week. Please have the model number and
serial number for your machine handy. Be sure that you are
calling from a telephone close to your machine so you can
describe your problem accurately and follow up on the
suggestions of the Customer Support Representative right
while you are on the phone. Our Customer Support
Representatives are trained on all current OKI products.
They can answer your questions regarding:
• Locations of sales and service dealers
• Installation of your machine
• Usage/normal maintenance of your machine
• Error message interpretation/solutions
• Parts and supplies identification
• Consumer relations
Note: Customer Support Representatives are not trained
to provide assistance with the use of commercial
software packages. Please consult your software
user’s manual for times and availability of their
support.
United States
Oki Data Americas, Inc.
2020 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
Phone: [phone]
Fax: [phone]
Canada
Oki Data Americas, Inc.
4140B Sladeview Crescent
Unit 7 & 8
Mississauga, ON
Canada LDL 6A1
Phone: [phone]
Fax: [phone]
United States
Oki Data Americas, Inc.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
Phone: [phone]
Fax: [phone]
Canada
Oki Data Americas, Inc.
4140B Sladeview Crescent
Unit 7 & 8
Mississauga, ON
Canada LDL 6A1
Phone: [phone]
Fax: [phone]

6 - English
Regulatory Information
ENERGY STAR
®
As an ENERGY STAR Partner, Oki Data has
determined that this product meets the
ENERGY STAR guidelines for energy
efficiency.
Year 2000 Compliance
This product is Year 2000 Compliant. It contains information
technology that accurately processes date and time data
between the years 1999 and 2000, and carries no issue for
the September 9, 1999 (9999) programming concern. This
product, when used in combination with products purchased
from other manufacturers, whose products properly
exchange data and time information, will accurately process
the date and time.
FCC Administrative Council for Terminal
Attachment Requirements for End Users
This device has been granted a registration number by the
Administrative Council for Terminal Attachment (ACTA),
under Part 68 and ACTA rules and regulations for direct
connection to the telephone lines. In order to comply with
these FCC rules, the following instructions must be carefully
read and applicable portions followed completely.
1.This equipment complies with Part 68 of FCC rules and
the requirements adopted by the ACTA. On the back of
the equipment is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this inf
2.The following USOC jacks may be used with this
equipment: RJ11C.
3.A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed
to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
4.The REN is used to determine the quantity of devices
which may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not
all areas, the sum of the RENs should not exceed five
(5.0). To be certain of the number of devices that may be
connected to the line, as determined by the total RENs,
contact the local telephone company. For products
approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the
label.
5.If the equipment, Product Name, causes harm to the
telephone network, the telephone company will notify you
in advance that temporary discontinuance of service may
be required. But if advance notice isn’t practical, the
telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
6.The telephone company may make changes in its
facilities, equipment, operations, or procedures that could
affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make the necessary modifications to maintain
uninterrupted service.
7.If trouble is experienced with this equipment (Product
Name), please contact the following for repair and/or
warranty information:
Oki Data Americas, Inc.
2000 Bishops Gate Blvd.
Mount Laurel, N.J. 08054-4620
Telephone:[phone] or
(800)-OKIDATA (800-654-3282)
If the equipment is causing harm to the telephone
network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
8.This equipment contains no user serviceable parts. Please
contact Oki Data for service.
9.This equipment cannot be used on public coin service
provided by the telephone company. Connection to Party
Line Service is subject to state tariffs. Contact your state
Public Utility Commission, Public Service Commission, or
Corporate Commission for information.
10.If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation of
this CX3535/4545 does not disable your alarm
equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a
qualified installer.
FCC Telephone Consumer Protection Act
The Telephone Consumer Protection Act of 1991 makes it
unlawful for any person to use a computer or other
electronic device, including FAX machines, to send any
message unless such message clearly contains in a margin
at the top or bottom of each transmitted page or on the first
page of the transmission, the date and time it is sent and an
identification of the business or other entity, or other
individual sending the message, and the telephone number
of the sending machine or such business, other entity, or
individual. (The telehone number provided may not be a 900
number or any other number for which charges exceed local
or long-distance transmission charges.)
To comply with this law, you must enter the following
information in your fax unit:
•
Date and time: see “Changing the Date and Time” under
Setting Your Terminal in the User’s Guide for instructions
on doing this.
•
Name and telephone number which identify the source
of your fax transmission:
see Your fax number/your
name under Setting Your Terminal in the User’s Guide for
instructions on doing this.
FCC Radio Frequency Interference Statement
WARNING: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference
in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not

7 - English
installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at their own expense.
Note: It is the responsibility of the user to obtain the
required shielded cable in order to ensure
compliance of this equipment with FCC regulations.
Changes or modifications not expressly approved by Oki
Data may void your authority to operate this device.
California Requirement
Perchlorate Warning Applicable to Lithium Batteries
Sold and/or Distributed in California
Perchlorate Material: special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Industry Canada (IC) Radio Interference
Statements
This Oki Data apparatus complies with the Class A limits for
radio interference as specified in the IC Radio Interference
Regulations.
Industry Canada (IC) Requirements for End
Users
This product meets the applicable Industry Canada technical
specifications.
The Ringer Equivalence Number is an indication of the
maximum number of devices allowed to be connected to a
telephone interface. The termination on an interface may
consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does
not exceed five.

8 - English
Material Safety Data Sheet
# 58409301
Cyan Toner, Type D2: P/N 44947307
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S) CAS No. wt.%
Polyester resin — 80-90
Organic Pigment — <10
Wax — <10
Amorphous Silica 7631-86-9 <5
Titanium dioxide 13463-67-7 <2
— TRADE SECRET
HAZARDS IDENTIFICATION
Emergency Overview : If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards : This product is not classified as flammable
or combustible. It will burn in case of fire.
Avoid contact with strong oxidizers such as chromate, bromate
and nitrates.
Routes of Exposure : Inhalation, dermal contact, incidental
ingestion
Inhalation : Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact : Non-irritant.
Dermal Contact : Non-irritant, non-sensitiser.
Ingestion : Not currently known.
Chronic Effects : See Section 11 Supplemental Health
Information.
Carcinogenicity : See Section 11 Supplemental Health
Information.
Reproductive/Developmental : Not identified.
Target Organs : Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure : Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product : Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact : Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact : Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion : Dilute stomach contents with several glasses of
water.
Inhalation : Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard : Product will burn in case of fire.
Flash Point : Not applicable
Flammable Limits : Not applicable
Autoignition Temperature : Not applicable
Flammability classification : Not applicable
Extinguishing Media : Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard : Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures : None
Hazardous Combustion Products : Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks : Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.
HANDLING AND STORAGE
Handling : Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion : This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage : Keep container in cool and dry area.
Hygienic Practices : Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA) as the product : 15mg/m3 (Total dust)
5mg/m3 (Respirable fraction)
Other substances : Not listed
ACGIH TLVs (TWA) as the product : 10mg/m3 (Total dust)
3mg/m3 (Respirable fraction)
Other substances : Not listed
DFG-MAK (TWA) as the product : 4mg/m3 (Inhalable fraction)
1.5mg/m3 (Respirable fraction)
All substances : Not listed
NOHSC (TWA) All substances : Not listed
Engineering Controls : Maintain adequate ventilation.
Eye Protection : Not required under intended use.
Skin Protection : Not required under intended use.
Respiratory Protection : Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance : Fine solid powder
Color : Cyan
Scent : Odorless
Melting Point : 110 - 150 degree (Softening point)
Specific Gravity(H2O=1) : 1.1 - 1.5
Vapor Pressure : Not applicable
Vapor Density (Air=1) : Not applicable
Evaporation Rate : Not applicable
Solubility in Water : Negligible
pH Value : Not a water-based product, therefore not applicable.

9 - English
Explosive Properties : little possiblity in intended use.
According to Explosive Evaluation, can form explosive dust-air
mixtures when finely dispersed in air, like most finely grained
organic powders.
STABILITY AND REACTIVITY
Stability : Stable
Incompatibility : Not identified.
Hazardous Decomposition Products : Carbon monoxide and
carbon dioxide.
Hazardous Polymerization : Will not occur.
SUPPLEMENTAL HEALTH INFORMATION
Acute oral toxicity : LD50 is greater than 2,000mg/kg. (This
was the highest attainable mass.)
Acute inhalation : LC50(4H) is in excess of 5.27mg/l. (This was
the highest attainable concentration.)
Eye irritation : Minimal irritant
Skin irritation : Non-irritant.
Skin sensitization : Non-sensitiser.
Mutagenicity : Negative in the Ames test.
Carcinogenicity : None known
Chronic Effects : None known
ECOLOGICAL INFORMATION
Aquatic environment : LC50 is greater than 1000mg/L (fish),
EC50 is greater than 1000mg/L (daphnia), EbC50 is greater than
1000mg/L (Algal). (This was the highest attainable mass.)
DISPOSAL CONSIDERATION
Dispose of in accordance with local, state and federal regulation.
Empty plastic container may be recycled.
TRANSPORTATION INFORMATION
Special Precautions : None
International Transport Information
UN Classification Number : Not applicable
Land DOT 49 CFR, ADR : Not classified as Dangeous Goods
Sea IMDG Code : Not classified as Dangeous Goods
Air ICAO-TI : Not classified as Dangeous Goods
REGULATORY INFORMATION
IARC : See section 11.
US/Canada Information
OSHA Hazard Communication Standard, 29CFR 1910. 1200 :
Not regulated.
Toxic Substance Control Act (TSCA) : All chemical substances
in this product comply with all applicable rules or orders under
TSCA.
RCRA (40 CFR 261) : Product or components not listed.
CERCLA/SARA Information : Not regulated.
NTP Annual Report on Carcinogens : Not listed as an NTP
carcinogen.
California Proposition 65 : Neither toner, or any of the
components, are listed as chemicals known to the State of
California to cause cancer or reproductive system effects.
Controlled Products Regulations(Canada) : This product has
been classified in accordance with the hazard criteria of the
CPR.
Workplace Hazardous Materials Information System(Canada) :
No toxicology information available
Other State Regulations : Not listed in the New Jersey Right to
Know List, Pennsylvania Hazardous Substance List, and
Massachusetts Substance List.
U.S./Canada Label Statements : LOW HAZARD FOR
RECOMMENDED HANDLING. Minimize dust generation and
accumulation. Use with adequate ventilation.
EU Information
Label Information According to Directives 67/548 EEC &
1999/45 EC
Symbol & Indication : Not required
Risk Phrase : Not required
Safety Advise Phrase : Not required
76/769/EEC : All chemical substances in this product comply
with all applicable rules or order under 76/769/EEC.
National requirement : No specific regulations or restrictions.
Regulation (EC) No. 1907/2006.(REACH) : All chemical
substances in this product comply with all applicable rules or
order under 1907/2006
OTHER INFORMATION
National Fire Protection Association (NFPA)
Classification:
Flammability : 1
Reactivity : 0
Health : 0
( 0 = insignificant, 1 = slight )
Hazardous Materials Information Systems (HMIS) :
Red (Flammability) : 1
Yellow (Reactivity) : 0
Blue (Acute Effects) : 0
( 0 = insignificant, 1 = slight )
Notice : Judgments as to the suitability of information herein for
purchaser's purposes are necessarily purchaser's responsibility.
Therefore, although reasonable care has been taken in the
preparation of such information, Toshiba Corporation extends no
warranties, makes no representations, and assumes no
responsibility as to the accuracy or suitability of such information
for application to purchaser's intended purposes or for
consequences of its use.
Abbreviation
(1) OSHA PEL stands for Permissible Exposure Limit under
Occupational Safety and Health Administration (USA).
(2) ACGIH TLV stands for Threshold Limit Value under American
Conference of Governmental Industrial Hygienists (USA).
(3) DFG-MAK stands for Maximale Arbeitsplatzkonzentrationen
under Deutsche Forschungsgemeinschaft.
(4) TWA stands for Time Weighted Average.
(5) NTP stands for National Toxicology Program (USA).
(6) NIOSH stands for National Institute for Occupational Safety
and Health (USA).
(7) DOT stands for Department of Transportation (USA).
(8) NOHSC stands for National Occupational Heath and Safety
Commission (Australia).
User’s Responsibility ____________
This bulletin cannot cover all possible situations which the
user may experience when using this product. Each aspect of
your operation must be examined in regard to if, or where,
additional precautions may be necessary. All health and

10 - English
safety information contained in this bulletin must be
provided to your employees or customers. It is your
responsibility to use this information to develop appropriate
work practice guidelines and employee instructional
programs for your operation.
Preparation Date of MSDS
Date: March 1, 2012.
Prepared by:
Oki Data Americas, Inc.
Engineering Services Department.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Tel: [phone]
Fax: [phone]
http://WWW.OKIPRINTINGSOLUTIONS.COM
my.okidata.com

11 - English
Material Safety Data Sheet
# 58409201
Magenta Toner, Type D2: P/N 44947306
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S) CAS No. wt.%
Polyester resin - - - 80-90
Organic Pigment - - - <10
Wax - - - <10
Amorphous Silica 7631-86-9 <5
Titanium dioxide 13463-67-7 <2
- - - TRADE SECRET
HAZARDS IDENTIFICATION
Emergency Overview: If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards: This product is not classified as flammable
or combustible. It will burn in case of fire.
Avoid contact with strong oxidizers such as chromate, bromate
and nitrates.
Routes of Exposure: Inhalation, dermal contact, incidental
ingestion
Inhalation: Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact: Non-irritant.
Dermal Contact: Non-irritant, non-sensitiser.
Ingestion: Not currently known.
Chronic Effects: See Section 11 Supplemental Health
Information.
Carcinogenicity: See Section 11 Supplemental Health
Information.
Reproductive/Developmental: Not identified.
Target Organs: Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure: Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product: Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact: Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion: Dilute stomach contents with several glasses of
water.
Inhalation: Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard: Product will burn in case of fire.
Flash Point: Not applicable
Flammable Limits: Not applicable
Autoignition Temperature: Not applicable
Flammability classification: Not applicable
Extinguishing Media: Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard: Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures: None
Hazardous Combustion Products: Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks: Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.
HANDLING AND STORAGE
Handling: Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion: This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage: Keep container in cool and dry area.
Hygienic Practices: Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA)
as the product: 15mg/m3 (Total dust) 5mg/m3 (Respirable
fraction)
Other substances: Not listed
ACGIH TLVs (TWA)
as the product: 10mg/m3 (Total dust) 3mg/m3 (Respirable
fraction)
Other substances: Not listed
DFG-MAK (TWA)
as the product: 4mg/m3 (Inhalable fraction) 1.5mg/m3
(Respirable fraction)
All substances: Not listed
NOHSC (TWA)
All substances: Not listed
Engineering Controls: Maintain adequate ventilation.
Eye Protection: Not required under intended use.
Skin Protection: Not required under intended use.
Respiratory Protection: Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Fine solid powder
Color: Magenta
Scent: Odorless
Melting Point: 110 - 150 degree (Softening point)
Specific Gravity(H2O=1): 1.1 - 1.5
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not applicable
Evaporation Rate: Not applicable
Solubility in Water: Negligible
pH Value: Not a water-based product, therefore not applicable.
Explosive Properties: little possiblity in intended use.

12 - English
According to Explosive Evaluation, can form explosive dust-air
mixtures when finely dispersed in air, like most finely grained
organic powders.
STABILITY AND REACTIVITY
Stability: Stable
Incompatibility: Not identified.
Hazardous Decomposition Products: Carbon monoxide and
carbon dioxide.
Hazardous Polymerization: Will not occur.
SUPPLEMENTAL HEALTH INFORMATION
Acute oral toxicity: LD50 is greater than 2,000mg/kg. (This
was the highest attainable mass.)
Acute inhalation: LC50(4H) is in excess of 5.13mg/l. (This was
the highest attainable concentration.)
Eye irritation: Non-irritant.
Skin irritation: Non-irritant.
Skin sensitization: Non-sensitiser.
Mutagenicity: Negative in the Ames test.
Carcinogenicity: None known
Chronic Effects: None known
ECOLOGICAL INFORMATION
Aquatic environment:
LC50 is greater than 1000mg/L (fish)
EC50 is greater than 1000mg/L (daphnia)
EbC50 is greater than 1000mg/L (Algal)
(This was the highest attainable mass.)
DISPOSAL CONSIDERATION
Dispose of in accordance with local, state and federal regulation.
Empty plastic container may be recycled.
TRANSPORTATION INFORMATION
Special Precautions: None
International Transport Information
UN Classification Number: Not applicable
Land DOT 49 CFR, ADR: Not classified as Dangeous Goods
Sea IMDG Code: Not classified as Dangeous Goods
Air ICAO-TI: Not classified as Dangeous Goods
REGULATORY INFORMATION
IARC: See section 11.
US/Canada Information
OSHA Hazard Communication Standard, 29CFR 1910. 1200:
Not regulated.
Toxic Substance Control Act (TSCA): All chemical substances
in this product comply with all applicable rules or orders under
TSCA.
RCRA (40 CFR 261): Product or components not listed.
CERCLA/SARA Information: Not regulated.
NTP Annual Report on Carcinogens: Not listed as an NTP
carcinogen.
California Proposition 65: Neither toner, or any of the
components, are listed as chemicals known to the State of
California to cause cancer or reproductive system effects.
Controlled Products Regulations(Canada): This product has
been classified in accordance with the hazard criteria of the
CPR.
Workplace Hazardous Materials Information System(Canada):
No toxicology information available
Other State Regulations: Not listed in the New Jersey Right to
Know List, Pennsylvania Hazardous Substance List, and
Massachusetts Substance List.
U.S./Canada Label Statements: LOW HAZARD FOR
RECOMMENDED HANDLING. Minimize dust generation and
accumulation. Use with adequate ventilation.
EU Information
Label Information According to Directives 67/548 EEC &
1999/45 EC
Symbol & Indication: Not required
Risk Phrase: Not required
Safety Advise Phrase: Not required
76/769/EEC: All chemical substances in this product comply
with all applicable rules or order under 76/769/EEC.
National requirement: No specific regulations or
restrictions.
Regulation (EC) No. 1907/2006 (REACH): All chemical
substances in this product comply with all applicable rules or
order under 1907/2006
OTHER INFORMATION
National Fire Protection Association (NFPA)
Classification:
Flammability: 1
Reactivity: 0
Health: 0
(0 = insignificant, 1 = slight )
Hazardous Materials Information Systems (HMIS):
Red (Flammability): 1
Yellow (Reactivity): 0
Blue (Acute Effects): 0
(0 = insignificant, 1 = slight )
Notice: Judgments as to the suitability of information herein for
purchaser's purposes are necessarily purchaser's responsibility.
Therefore, although reasonable care has been taken in the
preparation of such information, Toshiba Corporation extends no
warranties, makes no representations, and assumes no
responsibility as to the accuracy or suitability of such information
for application to purchaser's intended purposes or for
consequences of its use.
Abbreviation:
(1) OSHA PEL stands for Permissible Exposure Limit under
Occupational Safety and Health Administration (USA).
(2) ACGIH TLV stands for Threshold Limit Value under American
Conference of Governmental Industrial Hygienists (USA).
(3) DFG-MAK stands for Maximale Arbeitsplatzkonzentrationen
under Deutsche Forschungsgemeinschaft.
(4) TWA stands for Time Weighted Average.
(5) NTP stands for National Toxicology Program (USA).
(6) NIOSH stands for National Institute for Occupational Safety
and Health (USA).
(7) DOT stands for Department of Transportation (USA).
(8) NOHSC stands for National Occupational Heath and Safety
Commission (Australia).
User’s Responsibility ____________
This bulletin cannot cover all possible situations which the
user may experience when using this product. Each aspect of
your operation must be examined in regard to if, or where,
additional precautions may be necessary. All health and
safety information contained in this bulletin must be

13 - English
provided to your employees or customers. It is your
responsibility to use this information to develop appropriate
work practice guidelines and employee instructional
programs for your operation.
Preparation Date of MSDS
Date: March 1, 2012.
Prepared by:
Oki Data Americas, Inc.
Engineering Services Department.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Tel: [phone]
Fax: [phone]
http://WWW.OKIPRINTINGSOLUTIONS.COM
my.okidata.com

14 - English
Material Safety Data Sheet
# 58409101
Yellow Toner, Type D2: P/N 44947305
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S) CAS No. wt.%
Polyester resin - - - 80-90
Organic Pigment - - - <10
Wax - - - <10
Amorphous Silica 7631-86-9 <5
Titanium dioxide 13463-67-7 <2
- - - TRADE SECRET
HAZARDS IDENTIFICATION
Emergency Overview: If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards: This product is not classified as flammable
or combustible. It will burn in case of fire. Avoid contact with
strong oxidizers such as chromate, bromate and nitrates.
Routes of Exposure: Inhalation, dermal contact, incidental
ingestion
Inhalation: Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact: Non-irritant.
Dermal Contact: Non-irritant, non-sensitiser.
Ingestion: Not currently known.
Chronic Effects: See Section 11 Supplemental Health
Information.
Carcinogenicity: See Section 11 Supplemental Health
Information.
Reproductive/Developmental: Not identified.
Target Organs: Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure: Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product: Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact: Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion: Dilute stomach contents with several glasses of
water.
Inhalation: Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard: Product will burn in case of fire.
Flash Point: Not applicable
Flammable Limits: Not applicable
Autoignition Temperature: Not applicable
Flammability classification: Not applicable
Extinguishing Media: Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard: Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures: None
Hazardous Combustion Products: Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks: Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.
HANDLING AND STORAGE
Handling: Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion: This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage: Keep container in cool and dry area.
Hygienic Practices: Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA)
as the product: 15mg/m3 (Total dust) 5mg/m3 (Respirable
fraction)
Other substances: Not listed
ACGIH TLVs (TWA)
as the product: 10mg/m3 (Total dust) 3mg/m3 (Respirable
fraction)
Other substances: Not listed
DFG-MAK (TWA)
as the product: 4mg/m3 (Inhalable fraction) 1.5mg/m3
(Respirable fraction)
All substances: Not listed
NOHSC (TWA)
All substances: Not listed
Engineering Controls: Maintain adequate ventilation.
Eye Protection: Not required under intended use.
Skin Protection: Not required under intended use.
Respiratory Protection: Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Fine solid powder
Color: Yellow
Scent: Odorless
Melting Point: 110 - 150 degree (Softening point)
Specific Gravity(H2O=1): 1.1 - 1.5
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not applicable
Evaporation Rate: Not applicable
Solubility in Water: Negligible
pH Value: Not a water-based product, therefore not applicable.
Explosive Properties: little possiblity in intended use.
According to Explosive Evaluation, can form explosive dust-air

15 - English
mixtures when finely dispersed in air, like most finely grained
organic powders.
STABILITY AND REACTIVITY
Stability: Stable
Incompatibility: Not identified.
Hazardous Decomposition Products: Carbon monoxide and
carbon dioxide.
Hazardous Polymerization: Will not occur.
SUPPLEMENTAL HEALTH INFORMATION
Acute oral toxicity: LD50 is greater than 2,000mg/kg. (This
was the highest attainable mass.)
Acute inhalation: LC50(4H) is in excess of 5.30mg/l. (This was
the highest attainable concentration.)
Eye irritation: Non-irritant.
Skin irritation: Non-irritant.
Skin sensitization: Non-sensitiser.
Mutagenicity: Negative in the Ames test.
Carcinogenicity: None known
Chronic Effects: None known
ECOLOGICAL INFORMATION
Aquatic environmennt
LC50 is greater than 1000mg/L (fish)
EC50 is greater than 1000mg/L (daphnia)
EC50 is greater than 1000mg/L (Algal)
(This was the highest attainable mass.)
DISPOSAL CONSIDERATION
Dispose of in accordance with local, state and federal regulation.
Empty plastic container may be recycled.
TRANSPORTATION INFORMATION
Special Precautions: None
International Transport Information
UN Classification Number: Not applicable
Land DOT 49 CFR, ADR: Not classified as Dangeous Goods
Sea IMDG Code: Not classified as Dangeous Goods
Air ICAO-TI: Not classified as Dangeous Goods
REGULATORY INFORMATION
IARC: See section 11.
US/Canada Information
OSHA Hazard Communication Standard, 29CFR 1910. 1200:
Not regulated.
Toxic Substance Control Act (TSCA): All chemical substances
in this product comply with all applicable rules or orders under
TSCA.
RCRA (40 CFR 261): Product or components not listed.
CERCLA/SARA Information: Not regulated.
NTP Annual Report on Carcinogens: Not listed as an NTP
carcinogen.
California Proposition 65: Neither toner, or any of the
components, are listed as chemicals known to the State of
California to cause cancer or reproductive system effects.
Controlled Products Regulations(Canada): This product has
been classified in accordance with the hazard criteria
of the CPR.
Workplace Hazardous Materials Information System(Canada):
No toxicology information available
Other State Regulations: Not listed in the New Jersey Right to
Know List, Pennsylvania Hazardous Substance List, and
Massachusetts Substance List.
U.S./Canada Label Statements: LOW HAZARD FOR
RECOMMENDED HANDLING. Minimize dust generation and
accumulation. Use with adequate ventilation.
EU Information
Label Information According to Directives 67/548 EEC &
1999/45 EC
Symbol & Indication: Not required
Risk Phrase: Not required
Safety Advise Phrase: Not required
76/769/EEC: All chemical substances in this product comply
with all applicable rules or order under 76/769/EEC.
National requirement: No specific regulations or
restrictions.
Regulation (EC) No. 1907/2006 REACH): All chemical
substances in this product comply with all applicable rules or
order under 1907/2006
OTHER INFORMATION
National Fire Protection Association (NFPA)
Classification:
Flammability: 1
Reactivity: 0
Health: 0
(0 = insignificant, 1 = slight )
Hazardous Materials Information Systems (HMIS):
Red (Flammability): 1
Yellow (Reactivity): 0
Blue (Acute Effects): 0
(0 = insignificant, 1 = slight )
Notice: Judgments as to the suitability of information herein for
purchaser's purposes are necessarily purchaser's responsibility.
Therefore, although reasonable care has been taken in the
preparation of such information, Toshiba Corporation extends no
warranties, makes no representations, and assumes no
responsibility as to the accuracy or suitability of such information
for application to purchaser's intended purposes or for
consequences of its use.
Abbreviation:
(1) OSHA PEL stands for Permissible Exposure Limit under
Occupational Safety and Health Administration (USA).
(2) ACGIH TLV stands for Threshold Limit Value under American
Conference of Governmental Industrial Hygienists (USA).
(3) DFG-MAK stands for Maximale Arbeitsplatzkonzentrationen
under Deutsche Forschungsgemeinschaft.
(4) TWA stands for Time Weighted Average.
(5) NTP stands for National Toxicology Program (USA).
(6) NIOSH stands for National Institute for Occupational Safety
and Health (USA).
(7) DOT stands for Department of Transportation (USA).
(8) NOHSC stands for National Occupational Heath and Safety
Commission (Australia).
User’s Responsibility ____________
This bulletin cannot cover all possible situations which the
user may experience when using this product. Each aspect of
your operation must be examined in regard to if, or where,
additional precautions may be necessary. All health and

16 - English
safety information contained in this bulletin must be
provided to your employees or customers. It is your
responsibility to use this information to develop appropriate
work practice guidelines and employee instructional
programs for your operation.
Preparation Date of MSDS
Date: March 1, 2012.
Prepared by:
Oki Data Americas, Inc.
Engineering Services Department.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Tel: [phone]
Fax: [phone]
http://WWW.OKIPRINTINGSOLUTIONS.COM
my.okidata.com

17 - English
Material Safety Data Sheet
# 58409401
Black Toner, Type D2: P/N 44947308
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S) CAS No. wt.%
Polyester resin - - - 80-90
Carbon black 1333-86-4 3-8
Wax - - - <10
Amorphous Silica 7631-86-9 <5
Titanium dioxide 13463-67-7 <2
- - - TRADE SECRET
HAZARDS IDENTIFICATION
Emergency Overview: If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards: This product is not classified as flammable
or combustible. It will burn in case of fire. Avoid contact with
strong oxidizers such as chromate, bromate and nitrates.
Routes of Exposure: Inhalation, dermal contact, incidental
ingestion
Inhalation: Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact: Non-irritant.
Dermal Contact: Non-irritant, non-sensitiser.
Ingestion: Not currently known.
Chronic Effects: See Section 11 Supplemental Health
Information.
Carcinogenicity: See Section 11 Supplemental Health
Information.
Reproductive/Developmental: Not identified.
Target Organs: Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure: Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product: Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact: Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion: Dilute stomach contents with several glasses of
water.
Inhalation: Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard: Product will burn in case of fire.
Flash Point: Not applicable
Flammable Limits: Not applicable
Autoignition Temperature: Not applicable
Flammability classification: Not applicable
Extinguishing Media: Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard: Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures: None
Hazardous Combustion Products: Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks: Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.
HANDLING AND STORAGE
Handling: Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion: This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage: Keep container in cool and dry area.
Hygienic Practices: Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA)
as the product: 15mg/m3 (Total dust) 5mg/m3 (Respirable
fraction)
Carbon black: 3.5 mg/m3
Other substances: Not listed
ACGIH TLVs (TWA)
as the product: 10mg/m3 (Total dust) 3mg/m3 (Respirable
fraction)
Carbon black: 3.5 mg/m3
Other substances: Not listed
DFG-MAK (TWA)
as the product: 4mg/m3 (Inhalable fraction) 1.5mg/m3
(Respirable fraction)
All substances: Not listed
NOHSC (TWA)
All substances: Not listed
Engineering Controls: Maintain adequate ventilation.
Eye Protection: Not required under intended use.
Skin Protection: Not required under intended use.
Respiratory Protection: Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Fine solid powder
Color: Black
Scent: Odorless
Melting Point: 110 - 150 degree (Softening point)
Specific Gravity(H2O=1): 1.1 - 1.5
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not applicable
Evaporation Rate: Not applicable
Solubility in Water: Negligible
pH Value: Not a water-based product, therefore not applicable.

18 - English
Explosive Properties: little possiblity in intended use.
According to Explosive Evaluation, can form explosive dust-air
mixtures when finely dispersed in air, like most finely grained
organic powders.
STABILITY AND REACTIVITY
Stability: Stable
Incompatibility: Not identified.
Hazardous Decomposition Products: Carbon monoxide and
carbon dioxide.
Hazardous Polymerization: Will not occur.
SUPPLEMENTAL HEALTH INFORMATION
Acute oral toxicity: LD50 is greater than 2,000mg/kg. (This
was the highest attainable mass.)
Acute inhalation: LC50(4H) is in excess of 5.13mg/l. (This was
the highest attainable concentration.)
Eye irritation: Non-irritant.
Skin irritation: Non-irritant.
Skin sensitization: Non-sensitiser.
Mutagenicity: Negative in the Ames test.
Carcinogenicity: In 1996, the IARC classified carbon black as a
Group 2B carcinogen (possible human carcinogen).
Chronic Effects: In a study in rats by chronic inhalation
exposure to a typical toner, a mild to moderate degree of lung
fibrosis was observed in 92 % of the rats in the high
concentration (16 mg/m3)exposure group, and a minimal to
mild degree of fibrosis was noted in 22% of the animals in the
middle (4 mg/m3) exposure group. These findings are attributed
to "lung overloading", a general response to excessive amounts
of any dust retained in the lungs for a prolonged period.
ECOLOGICAL INFORMATION
Aquatic environment
LC50 is greater than 1000mg/L (fish)
EC50 is greater than 1000mg/L (daphnia)
EbC50 is greater than 1000mg/L (Algal)
(This was the highest attainable mass.)
DISPOSAL CONSIDERATION
Dispose of in accordance with local, state and federal regulation.
Empty plastic container may be recycled.
TRANSPORTATION INFORMATION
Special Precautions: None
International Transport Information
UN Classification Number: Not applicable
Land DOT 49 CFR, ADR: Not classified as Dangeous Goods
Sea IMDG Code: Not classified as Dangeous Goods
Air ICAO-TI: Not classified as Dangeous Goods
REGULATORY INFORMATION
IARC: See section 11.
US/Canada Information
OSHA Hazard Communication Standard, 29CFR 1910. 1200:
Not regulated.
Toxic Substance Control Act (TSCA): All chemical substances
in this product comply with all applicable rules or orders under
TSCA.
RCRA (40 CFR 261): Product or components not listed.
CERCLA/SARA Information: Not regulated.
NTP Annual Report on Carcinogens: Not listed as an NTP
carcinogen.
California Proposition 65: Neither toner, or any of the
components, are listed as chemicals known to the State of
California to cause cancer or reproductive system effects.
Controlled Products Regulations(Canada): This product has
been classified in accordance with the hazard criteria of the
CPR.
Workplace Hazardous Materials Information System(Canada):
No toxicology information available
Other State Regulations: Carbon black is listed in the New
Jersey Right to Know List, Pennsylvania Hazardous Substance
List, and Massachusetts Substance List.
U.S./Canada Label Statements: LOW HAZARD FOR
RECOMMENDED HANDLING. Minimize dust generation and
accumulation. Use with adequate ventilation.
EU Information
Label Information According to Directives 67/548 EEC &
1999/45 EC
Symbol & Indication: Not required
Risk Phrase: Not required
Safety Advise Phrase: Not required
76/769/EEC: All chemical substances in this product comply
with all applicable rules or order under 76/769/EEC.
National requirement: No specific regulations or
restrictions.
Regulation (EC) No. 1907/2006 (REACH): All chemical
substances in this product comply with all applicable rules or
order under 1907/2006
OTHER INFORMATION
National Fire Protection Association (NFPA)
Classification:
Flammability: 1
Reactivity: 0
Health: 0
(0 = insignificant, 1 = slight )
Hazardous Materials Information Systems (HMIS):
Red (Flammability): 1
Yellow (Reactivity): 0
Blue (Acute Effects): 0
(0 = insignificant, 1 = slight )
Notice: Judgments as to the suitability of information herein for
purchaser's purposes are necessarily purchaser's responsibility.
Therefore, although reasonable care has been taken in the
preparation of such information, Toshiba Corporation extends no
warranties, makes no representations, and assumes no
responsibility as to the accuracy or suitability of such information
for application to purchaser's intended purposes or for
consequences of its use.
References: IARC (1996) IARC Monographs on the Evaluation
of the Carcinogenic Risks of Chemicals to Humans, Vol. 65,
Printing Processes and Printing Inks, Carbon Black and Some
Nitro Compounds, Lyon, pp. 149-261.
H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H.
Ernst, R. Kilpper, J. C. MacKenzie, P. Morrow, U. Mohr, S.
Takenaka, and R. Mermelstein (1991).
Pulmonary Response to Toner upon Chronic Inhalation Exposure
in Rats, Fundamental and Applied Toxicology 17, pp. 280-299.
Abbreviation:
(1) OSHA PEL stands for Permissible Exposure Limit under
Occupational Safety and Health Administration (USA).

19 - English
(2) ACGIH TLV stands for Threshold Limit Value under American
Conference of Governmental Industrial Hygienists (USA).
(3) DFG-MAK stands for Maximale Arbeitsplatzkonzentrationen
under Deutsche Forschungsgemeinschaft.
(4) TWA stands for Time Weighted Average.
(5) IARC stands for International Agency for Research on
Cancer.
(6) NTP stands for National Toxicology Program (USA).
(7) NIOSH stands for National Institute for Occupational Safety
and Health (USA).
(8) DOT stands for Department of Transportation (USA).
(9) NOHSC stands for National Occupational Heath and Safety
Commission (Australia).
User’s Responsibility ____________
This bulletin cannot cover all possible situations which the
user may experience when using this product. Each aspect of
your operation must be examined in regard to if, or where,
additional precautions may be necessary. All health and
safety information contained in this bulletin must be
provided to your employees or customers. It is your
responsibility to use this information to develop appropriate
work practice guidelines and employee instructional
programs for your operation.
Preparation Date of MSDS
Date: March 1, 2012.
Prepared by:
Oki Data Americas, Inc.
Engineering Services Department.
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054-4620
Tel: [phone]
Fax: [phone]
http://WWW.OKIPRINTINGSOLUTIONS.COM
my.okidata.com

20 - English
Material Safety Data Sheet
# 58409701
Cyan Developer, Type D2: P/N 44957903
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S) CAS No. wt.%
Ceramic materials and 66402-68-4 >90
wares, chemicals
Polyester resin --- <10
Organic Pigment --- <1
Amorphous Silica 7631-86-9 <1
--- TRADE SECRET
HAZARDS IDENTIFICATION
Emergency Overview : If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards : This product is not classified as flammable
or combustible. It will burn in case of fire.
Avoid contact with strong oxidizers such as chromate, bromate
and nitrates.
Routes of Exposure : Inhalation, dermal contact, incidental
ingestion
Inhalation : Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact : Non-irritant.
Dermal Contact : Non-irritant, non-sensitiser.
Ingestion : Not currently known.
Chronic Effects : See Section 11 Supplemental Health
Information.
Carcinogenicity : See Section 11 Supplemental Health
Information.
Reproductive/Developmental : Not identified.
Target Organs : Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure : Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product : Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of this
product.
FIRST AID MEASURES
Eye Contact : Immediately flush eyes with plenty of water for at
least 15 minutes. If irritation persists, call a physician.
Skin Contact : Wash with soap and water. Wash clothing before
reuse. If irritation occurs or is persistent, seek medical attention.
Ingestion : Dilute stomach contents with several glasses of
water.
Inhalation : Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard : Product will burn in case of fire.
Flash Point : Not applicable
Flammable Limits : Not applicable
Autoignition Temperature : Not applicable
Flammability classification : Not applicable
Extinguishing Media : Foam, halon, carbon dioxide, dry
chemical & water fog.
Unusual Fire & Explosion Hazard : Combustible powder. Dust
of this product at sufficient concentrations can form explosive
mixtures with air.
Fire Fighting Procedures : None
Hazardous Combustion Products : Carbon monoxide, carbon
dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks : Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner is
available, sweep slowly to minimize generation of dust during
clean-up. Residue can be removed with soap and cold water.
HANDLING AND STORAGE
Handling : Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion : This material is capable of
creating a dust explosion. Keep away from heat, sparks & flame.
Storage : Keep container in cool and dry area.
Hygienic Practices : Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly after
handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA) as the product : 15mg/m3 (Total dust)
5mg/m3 (Respirable fraction)
Other substances : Not listed
ACGIH TLVs (TWA) as the product : 10mg/m3 (Total dust)
3mg/m3 (Respirable fraction)
Other substances : Not listed
DFG-MAK (TWA) as the product : 4mg/m3 (Inhalable fraction)
1.5mg/m3 (Respirable fraction)
All substances : Not listed
NOHSC (TWA) All substances : Not listed
Engineering Controls : Maintain adequate ventilation.
Eye Protection : Not required under intended use.
Skin Protection : Not required under intended use.
Respiratory Protection : Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance : Fine solid powder
Color : Cyan
Scent : Odorless
Melting Point : No data available
Specific Gravity(H2O=1) : 4.5 - 5.5
Vapor Pressure : Not applicable
Vapor Density (Air=1) : Not applicable
Evaporation Rate : Not applicable