Oki GL408e User manual

For printer models:
CUTTER INSTALLATION GUIDE
GL 4xxeSeries
For printer models:
Read this Installation Guide before and during the installation of
the above accessory. Keep this Installation Guide handy for
future reference.

2
Simple-Cutter Installation Guide
1 General
1.1 Important information
This quick guide provides important information on how to
setup your new SATO product.
Be sure to read this quick guide thoroughly before using this
printer. It is an integral part of the product and should be kept
in the immediate vicinity of the device and available to the
operating staff.
1.2 Limitation of liability
All information in this manual have been compiled under due
consideration of federal standards and regulations.
The manufacturer will not be held liable for damage resulting
from:
zDisregarding these instructions
zUnintended use of the printer
zUnauthorized technical modifications
zUse of unapproved spare parts
zUse of unapproved consumables
FCC WARNING
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTICE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.

3
Simple-Cutter Installation Guide
1.3 Explanation of symbols
This instruction manual uses various warning icons to help you
understand the safe operation of your printer. Explanations of
the icons are below.
WARNING!
Indicates neglectful or erroneous use may cause
irreparable damage to the product, serious injury
to the operator, or worse.
CAUTION!
Indicates a specific point where caution should be
used. The graphic within the triangle will indicate
the specific issue, i.e.; the sign on the left
indicates a caution for potential electrical shock.
CAUTION!
Indicates a potentially hazardous situation
which, if not avoided, may result in damage to
your product or host equipment.
NOTE!
Emphasizes useful tips or recommendations for
efficient and smooth operation of your printer.

4
Simple-Cutter Installation Guide
1.4 Contact and Document Information
.
Extensive contact information of worldwide SATO operations can be found on the Internet at
www.satoworldwide.com
Version: SI-GL4xxe-01rA-05-06-07-CUTIG © Copyright 1994 – 2007
All rights reserved. No part of this document may be reproduced or issued to third
parties in any form whatsoever without the express permission of SATO. The materials
in this document are provided for general information and are subject to change without
notice. SATO assumes no responsibilities for any errors that may appear.
S
A
TO GROUP OF COMP
A
NIES
Inte
r
national Headqua
r
ters
A
me
r
icas
S
A
T
O INTERN
A
TIONAL PTE. LTD
438A AlexandraRoad#05-01/04,
Alexandra
Technopark, Singapore 119967
Phone: [phone] Fax : [phone]
Email: [e-mail]
SATO AMERICA, INC.
10350 Nations Ford Road Suite A,
Charlotte,NC
28273
Phone: [phone] Fax: [phone]
Email: [e-mail]
SATO INTERNATIONAL EUROPE N.V.
(
Re
g
ional HQ
)
A
mericas
Euro
p
e
S
A
TOINTERN
A
TION
A
L
A
MERICA,INC.
(Regional HQ)
10350 Nations FordRoad Suite A,
Charlotte, NC 28273
Phone: [phone] Fax: [phone]
Email:[e-mail]
SATO LABELING SOLUTIONS AMERICA, INC.
1140 Windham Parkway, Romeoville, Illinois 60446
Phone: [phone] Fax : [phone]
Email:[e-mail]
Horticultural Division
930Jimmy Ann Drive
Daytona Beach, FL 32117
Phone: [phone] Fax: [phone]
SATO UK LTD
Valle
y
Road, Harwich, Essex En
g
land Co124RR,
Leuvensesteenweg 369,1932 Sint-Stevens-Woluwe, Brussels, Belgium
Phone:[phone] Fax:[phone]
Email: [e-mail]
SATO LABELLING SOLUTIONS EUROPE GmbH
Ersheimer Straße
71,
69434 Hirschhorn, Germany
Phone: [phone] Fax: [phone]
SATO FRANCE SAS
Parc D'Activities - Rue Jacques Messager - 59175 Templemars, France
Phone: [phone] Fax: [phone]
Asia Pacific & Oceania
SATO INTERNATIONAL ASIA PACIFIC PTE. LTD.
(RegionalHQ)
438A AlexandraRoad#05-01/04,
Alexandra
Technopark, Singapore 119967
Phone : [phone] Fax : [phone]
Email: [e-mail]
SATO ASIA PACIFIC PTE. LTD.
438A AlexandraRoad#05-01/04, Alexandra Technopark, Singapore 119967
Phone: [phone] Fax: [phone]
Email:[e-mail]
S
A
TOSH
A
NGH
A
I CO., LTD.
UnitedKingdom
Phone: [phone] Fax : [phone]
Email: [e-mail]
SATO POLSKA SP Z O.O.
Ul.Wroclawska123,55-015 Radwanice
K/Wroclawia, Poland
Phone:[phone] Fax:[phone]
Email:[e-mail]
SATO IBERIA S.A.
Dels Corrals Nous, 35-39, Pol.Can Roqueta,
08202 - Sabadell,Barcelona, Spain
Phone:[phone] Fax : [phone]
SATO AUTO-IDMALAYSIA SDN. BHD.
No.25,Jalan Pemberita U1/49, Temasya
Industrial Park
SectionU1, 40150 Shah Alam,
Selangor
Darul Ehsan, Malaysia
Phone: [phone] Fax: [phone]
Email:[email protected]
SATO AUTO-ID (THAILAND) CO., LTD.
292/1 Moo 1 Theparak Road, TumbolTheparak,
Amphur Muang, Samutprakarn 10270
Phone: [phone] Fax: [phone]
S
A
T
O
A
USTRALI
A
PTY LTD.
307 Haining Road,ACE Bldg,10th Floor,
Hongkou Area,
Shanghai,China200080
Phone: [phone] Fax: [phone]
SATO NEW ZEALAND LTD
3
0
A
po
l
l
o
D
r
i
e
M
a
i
r
a
n
g
i
B
a
1
/
1 Nursery
A
venue, Clayton Business Park (1508 Centre Road) Clayton
VIC 3168, Melbourne, Australia
Phone: [phone] Fax: [phone]
For a full list of all SATO offices,
re
f
er to ww
w
.satoworldwide.com

5
Simple-Cutter Installation Guide
GL4xxe Label Cutter Installation
1
5
3
4
3
2
The Label Cutter is housed in a cover assembly that is designed to replace the
factory-installed front cover of the GL4xxe series printer. Follow the procedures
below to install the Label Cutter.
1. Make sure the printer is OFF and disconnected from the power supply.
2. Lift up the side cover to access the original housing cover (1).
3. Remove the housing cover by unscrewing the thumbscrew (2) at the
side of the printer.
4. Affix the Label Cutter (3) to the printer by plugging the white connector
(4) into the complementary connector (5) on the printer.
5. Locate the thumbscrew removed in Step 3 above, and screw it back into
place to secure the Label Cutter. Note: Ensure that the cable is not
pinched when you install the label cutter cover in place.
6. Restore power to the Printer and configure the printer to use the cutter.
(See next page)
7. Perform a test print and ensure that the label cutting process is correct.
Figure 1. Preparing and installing the Simple Cutter

6
Simple-Cutter Installation Guide
Dispenser setup via the LCD Menu
1. Turn the printer ON and wait for it to initialize and go into
ONLINE mode.
2. Press the Line Button to go to OFFLINE mode.
3. Press the Function Button to display the different menu icons
4. Select the Advanced Mode Menu and press the Enter Button.
5. Scroll to the Media Handling menu using the cursor buttons.
6. Once the cutter has been installed correctly, this menu allows you
to select the Cutter option to activate the cutter’s functionality.
7. When completed, go back to ONLINE mode after saving the new
settings.
Once the Label Cutter has been installed, the printer automatically detects it.
The cutter is not activated by default, except via the printer driver or via SBPL
software commands.
PRINTER CONFIGURATION FOR CUTTER OPERATION
OFFLINE
ADVANCED MODE
Figure 2.
Setting
the Cutter
option

7
Simple-Cutter Installation Guide