olympia electronics GR-270 User manual

Page 1 from 4923270000_09_004
GENERAL
o
These devices are used indoors (ta 40 C)
in places where emergency luminaires are
needed. The luminaires GR-270 and GR-
272 are suitable for corridors lighting and
the GR-271 and GR-273 for open area
lighting. Each device must be permanently
connected to mains power supply. In
normal operation the battery is charging. In
case of a mains power supply failure the
device will light the illumination led
automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the
installation instructions οn page 2.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personel only.
2. The device must be connected to the
mains power supply thru a fuse dependent
by the total amount of the line’s power
load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pushing the TEST button (use a pointy tool
with diameter of 2mm max.) to check the
emergency cirquit. The illumination LED
should light as long as the TEST button is
pressed. In the opposite condition contact
the installer.
4. It is sugested to check every 6 months
the minimum autononous duration by
disconnecting the mains power supply.
Count the time that the luminaire lights and
in case of less time than the minimum
autonomous duration the battery must be
r e p l a c e d . I f t h e m e a s u r e d t i m e i s
considerably less than the minimum
autonomous duration contact the installer.
I n c a s e o f b a t t e r y o r l i g h t s o u r c e
replacement, these must be replaced by
parts of the same type, by the manufacturer
or by a competent person.
5. In case of inactive use for a period
greater than 2 months, disconnect the
batt ery by pulli ng out the ba ttery ’s
connector.
6. I s not allowed to discard batteries in t i
to common trash bins, they must be
discarded only in battery recycling
points. Do not incinerate.
NON MAINTAINED SPOT LIGHT EMERGENCY
LUMINAIRES WITH 1 WHITE POWER LED
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION
WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-MH)
CHARGE TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
220-240V AC / 50-60Hz
3 hours1.5 hour
24 hours
Deep discharge and overcharge protection
IP40
3.6V/1.5Ah
160lm 120lm
1 white power LED
o
5 to 40 C
Up to 95%
ABS/PC, PC
3 years (1 year for the battery)
380gr.
Ø125 x 65 mm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Charge, TEST button
GR-270 GR-271 GR-272 GR-273
2.4W / 2.7VA
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)
Thank you for your trust in our products
Olympia Electronics - European manufacturer

Page 2 from 4
The light source contained in this luminaire shall only be replaced by the
manufacturer, or his agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
INSTALLATION INSTRUCTIONS
32
Initial installation
1 Untighten the screw and pull up the reflector.
2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²
or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!
The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ
rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a
hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the
power terminal, connect the wires as shown in the picture and attach the power terminal (10A max).
3 Place the battery’s connector to the corresponding connector on the P.C.B.
4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire
is ready for mounting.
NOTE!! After finishing the installation you must power the luminaire for, at least, 24 hours for
battery charging to perform the nominal autonomy.
GR-270, GR-272
GR-271, GR-273
ATTENTION!!!
During installation follow this light direction.
Corridor
lighting
Open
area
lighting
CHARGE TEST
CHARGE TEST CHARGE TEST
96
65
125
CHARGE TEST
Battery
charge
indication
LED
Figure 4
Test
button
923270000_09_004
L
N
Cable
entry
hole
1

Page 3 from 4
Mounting the lamp in suspended ceiling.
Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):
Step 1
Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.
Step 2
Push up the luminaire, as shown in figure 2.
Step 3
Continue to push upwards until the lamp locks.
If you want to pull off the device, put a flat blade
screwdriver, between the device and the ceiling.
Figure 2
Figure 3
Figure 1
Ø110mm
923270000_09_004
Surface mounting
Install the luminaire according to the following steps:
Step 1. Follow the step 1 of the installation instructions.
Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling installation.
Step 3. (Figure )Drill 2 holes on the base 5 using a 4mm drill bit in order to permit the retaining screws to
pass. Mark these two drilled points on the required mounting location, drill the holes and install
the supplied plastic plugs. ATTENTION!! Especially for the GR-270 and GR-272 luminaire
installation on the ceiling you must align the base with the indications on the luminaire’s base.
Step 4. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to the
require location.
Step 5. Follow the steps 2,3 and 4 of the installation instructions.
Figure 4 Figure 5
Retaining fastener
Drill here
Indications

Page 4 from 4
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Remove the luminaire from the suspended ceiling (figure 3).
2. Follow the step 1 of the installation instructions.
3. Disconnect the connector and remove the old battery.
4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in
the position of the old one.
5. Replace the removed parts (step 1 and 4) and power the device.
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
60 °C max. across the board 45 °C max. across the board
Non reversible connection between main pcb and led module
5.8-6.2V DC
1.3W 1W
1903175
GR-270 GR-271 GR-272 GR-273
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. Ο.N.R. Thessaloniki-Κaterini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
[email protected]
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non maintained (*)
A: Including test device
90: 1.5 hour duration
180: 3 hours duration
(*) Non Maintained operation: The luminaire lights its illumination source, only in power
supply’s failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the
mains power supply or not.
923270000_09_004
CAUTION : Do not view directly with bare eyes.