olympia electronics GR-427/12L User manual

GENERAL
o
These luminaires are used indoors (ta 40 C)
where emergency light is needed.
E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y
connected to mains power supply.
In normal operation the led strip lights and the
battery is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically
in emergency mode. When the mains power
supply is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 4.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost
its energy. During this operation the luminaire
enters the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Battery charging
The battery charging is completely controled. In
this case, is achieved the perfect battery
maintenance , as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance
current.
Manual Test
The manual test can be conducted only if the
main power supply and the battery is connected.
By pressing the test button briefly an operation
test is initiated. During this test period all
indication LEDs are OFF.
Automatic test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
main power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic autonomous Test is conducted
and measures the luminaire`s back up
operation. This test is conducted automatically
every six months. In order to be performed, the
main power supply and the battery should be
connected (the battery should be charged). If
the battery is not charged, the test is postponed
until the battery is completely charged. If during
the Automatic Autonomous Test the luminaire’s
duration is lower than the named, then the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
923427000_09_005
Page 1 from 5
GR-427/12L SELF TESTING MAINTAINED EMERGENCY LUMINAIRE
220-240V AC/50-60Hz
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 5)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (230V / EMERGENCY)
ILLUMINATION SOURCE
480 min
24h
Charge, lamp fault, fault indication LED, TEST button
From overcharge and full discharge
IP42
12 white LED’s
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)
272 x 121 x 50 mm
600gr.
100lm / 100lm
3,6V/3Ah
3,5W / 7VA
Thank you for your trust in our products
Olympia Electronics - European manufacturer

Page 2 from 5
emergency mode is at least the one that is
stated in the list of the first page. During
emergency mode, a LED strip test is also
performed.
Resetting Errors
Push the Test button for 5 seconds, to
extinguish all the indicated LED errors. Then
the luminaire enters regular operation mode.
Indication LED status (with connected
mains power supply).
AC Charge
On: Good charge current.
Οff: No battery (No charging current
or disconnected battery).
Lamp fault
Οn: faulty LED strip.
Off: Good LED strip.
Fault
Οff: Battery OK.
Blink (With AC Charge LED ON): Autonomy or
low battery problem
(the battery must be replaced).
Blink (With AC Charge LED Off):
No charging current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
2. The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line’s power load.
I n c a s e o f b a t t e r y o r l i g h t s o u r c e
replacement, these must be replaced by parts of
the same type, by the manufacturer or by a
competent person.
t i
in battery recycling
points. Do not incinerate.
3 .
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by pulling
out the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
Suspended ceiling
Α-3018 mounting springs
1
2
3
Mounting methods
All luminaires, can be mounted either surface or in
suspended ceilings.
Suspended ceiling installation.
On the bottom of the base plastic of the luminaire there
are two H shaped cut outs. These are used to install
the A-3018 mounting springs.
1. With a sharp tool remove the appropriate plastic
pieces to fit the mounting springs. First place the edges
of the mounting spring to the respective holes and
install the one end of the coil to the support axis.
2. Install the other end of the coil to the other support
axis.
3. Bend the springs and place the luminaire to the
respective suspended ceiling’s hole.
The luminaire’s placement to the suspended ceiling
must be done after the connection with power supply
cables.
Mounting the luminaire
in a suspended ceiling
Required
opening in
a suspended
ceiling
260
110
923427000_09_005

Page 3 from 5 923427000_09_005
Installation methods
A-3018
Special mounting
springs for
suspended ceiling
installation
Mounting springs Α-3018
Wall or ceiling installation Suspended ceiling installation
MARKING PANEL SP-115
A marking panel SP-115 can be installed on the
luminaire in 3 different locations. This marking
panel is installed perpendicular to the diffusor of
the luminaire, as shown in the pictures below.
The panel is pre-printed and has a plastic
accessory on each side that is used to fasten the
panel to the luminaires.
There are 2 arrow stickers that can be placed in
each side of the marking panel to point to the
desired direction.
Placing the SP-115 marking panel
Place the plastic mounting accessories of the
marking panel as shown in pictures.
A-3018
SP-115 marking panel
Suspended ceiling installation
with Α-3018 mounting springs
and SP-115 marking panel
Ceiling installation
with SP-115 marking panel
Wall installation with SP-115
marking panel

923427000_09_005
Page 4 from 5
45 6
INSTALLATION INSTRUCTIONS
2
A
Base plastic
Cable entry channels
Luminaire mounting holes
3
B
1
A
B
Diffusor
Reflector
Base plastic
N
L
L1
1 To install the luminaire you must dismantle it to 3 parts.
2 Place a flat blade screwdriver in the area Α to release the diffusor’s
plastic hook.
3 Place a flat blade screwdriver in the area B to release the reflector’s
plastic hook.
4 Use the included mounting parts to mount the base plastic.
Pass the mains cable thru a cable entry channel. The luminaire must
be connected to a permanent electrical installation to ensure the
immobilization of the cable.
5 Place the battery’s connector to the corresponding connector on the
P.C.B.
6 Connect the mains cables to the respective detachable terminal
block. Ν for neutral, L for live wire and L1 for the maintained
operation. The L1 wire can be connected to an external switch to
control the maintained or non maintained operation of the luminaire.
For permanent maintained operation use two wires to power the
luminaire, Ν for neutral and L for live wire, and link the L and L1.
7 Refit the removed parts in steps 2 and 3 (mind the correct
orientation) and the luminaire is ready to operate.
N
N
L
L
External
switch
Link
Controled operation of the luminaire
Permanent maintained operation
NN
L L
L1 L1
NOTE!!
After finishing the installation you must power the luminaire at least for 24 hours for battery
charging to perform the named autonomy.
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Follow the step 2 and 3 of the installation procedure.
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in
the position of the old one.
4. Follow the step 7 of the installation procedure and power the device.

923427000_09_005
Page from5 5
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
45 °C max. across the board
8.4-9.9VDC
2.16W
0211163
GR-427/12L
Cable connection between main pcb and led module
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated safety sign
480: 8 hours duration
Note!! The installer should fill in, on the specification
label, the letter G if the luminaire is used as a safety
sign.
4
X 1 8 0A G
(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.