olympia electronics GR-939/30L/LT User manual

GENERAL
This luminaire is used in places with low
o
temperature (-20 C) where emergency
luminaires are needed.
Each illumination sign must be permanently
connected to mains power supply. In normal
operation the led strip lights and the battery is
charging. In case of a mains power supply
failure the illumination sign will light the led
strip automatically in emergency mode. When
the mains power supply is restored the device
turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
Battery Charging
The battery charging is completely controlled.
In this case, is achieved the perfect battery
maintenance, as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance
current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost
its energy. During this operation the
illumination sign enters the idle state and
battery consumption is negligible, in order to be
protected from deep discharge.
Manual Test
The manual test can be conducted only if the
mains power supply and the battery is
connected. By pressing the TEST/RESET
button briefly (page 3) an emergency operation
test is initiated. During this test period all
indication LEDs are OFF.
Automatic Operational Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
mains power supply and the battery should be
connected.
Manual Autonomous Test
If the Test button is pressed for a period
between 5 to 10 seconds (with the battery fully
charged), the illumination sign will enter in
counting autonomy condition. If the battery is
not fully charged this command is ignored. The
BATTERY FAULT blinks during the
measurement, indicating this process to the
user. This measurement duration is equal with
the nominal autonomous duration of the
illumination sign (1.5 hour or 3 hours) and at the
end of the process, if the measured duration
was at least the nominal autonomous duration,
the BATTERY FAULT is turned OFF, in the other
hand stays continuously ON indicating to the
Page 1 from 5 923939016_09_007
WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES
ΤΕΧΝΙΚΑ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ
90 min
Charge, Lamp fault, Battery fault , TEST button
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
31W / 33VA (<0°C)
3.6V / 2Ah
GR-938/30L/LT
180 min
24h
From overcharge and deep discharge
4 years
IP65
280lm / 230lm
White LEDs
o
-20 to +40 C
Up to 95%
Bayblend FR3010, transparent polycarbonate
3 years (1 year for the battery)
940gr. 1050gr.
32W / 35VA (<0°C)
3.6V / 4Ah
220-240VAC 50-60Hz
363 x 145 x 73 mm
GR-939/30L/LT
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
EXPECTED BATTERY LIFETIME
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
BATTERIES (Ni-ΜΗ)
TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 4)
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.

Page 2 from 5
user that the battery must be replaced.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the illumination sign’s back up
operation and emergency duration. This test is
conducted automatically every six months. In
order to be performed, the mains power supply
and the battery should be connected and fully
charged. If the battery is not fully charged, the
test is postponed until the battery is
completely charged. If during the Automatic
Autonomous Test the luminaire’s duration is
lower than the nominal, then the battery must
be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
LED strip test is also performed.
Resetting Errors
Push continuously the TEST/RESET button for
>10 seconds, to delete all the indicated LED
errors . Then the luminaire enters regular
operation mode.
Test Switch (Briefly)
Pressing the test switch less than 5 seconds
will initiate a light source test (last for 3 secs).
Pressing the test switch between 5 to 10
seconds will initiate a manual battery duration
test. This test will not be started if the battery
is not fully charged (i.e. If the green LED is
flashing). If the test switch is pressed for more
than 10 seconds, the device will delete all
errors).
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device must be connected to the mains
power supply through a fuse dependent by the
total amount of the line’s power load.
3. In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
4. In case of inactive use for a period
greater than 2 months, disconnect the
battery by pulling out the battery’s
connector.
5. I s not allowed to discard batteries in to t i
common trash bins, they must be discarded
only in battery recycling points. Do not
incinerate.
Battery Replacement
1. Unfasten the 4 retaining screws (step 8 of the
installation instructions) and remove the
diffusor.
2. Unfasten the 2 retaining screws step 7 of the
installation instructions and remove the
reflector.
3. Remove the old battery and place a new on
of the same type and characteristics.
4. Replace the removed parts (previous steps
1,2).
Important notice for the installed luminaires
in one area !!!
The installer must connect the battery’s
connector first and then should power the
luminaire. The batteries connection must have at
least a time variation of 1.5 minute for each
luminaire. With this variation, it is ensured that the
non synchronized Automatic Autonomous Test
for two or more luminaires installed in one area, is
not conducted in the same day.
923939016_09_007
(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated
*90: 1.5 hour duration
180: 3 hours duration
Note!! The installer should fill in, on the specification label,
the letter G if the luminaire is used as a safety sign.
*
X 1 9 0A G

Page 3 from 5
INSTALLATION INSTRUCTIONS
Step 1. Remove the diffusor. Place a flat blade screwdriver and pull the reflector gently (with
opposite orientation in relation to the plastic base).
Step 2. Install the included plastic cover in to the unused hole and install the base plastic (with
the included mounting screws and plugs).
Step 3. Always use in any case round mains cable, with a diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the tightness isolation IP65). Install the cable gland, pass the round cable thru and
tighten it all the way. When fastening the cable gland retain the main body of the gland in a
steady position and rotate only the internal plastic screw, this will prevent the rubber grommet
from being damaged.
Step 4. Place the battery’s connector to the corresponding connector on the P.C.B.
Step 5. Connect the mains cables to the respective terminal block (connect the ground wire if
required). Ν for neutral, L for Live Wire and L1 for the maintained operation. The L1 wire
can be connected to an external switch to control the maintained or non maintained operation of
the luminaire. For permanent maintained operation use two wires to power the luminaire, Ν for
neutral and L for Live Wire, and Link the L and L1.
Step 6. Install the included tie (if needed) to fasten securely the power cables.
Step 7. Refit the reflector and fasten the two small screws (included).
Step 8. Finally place the diffusor by using the 4 screws (tightening torque 1.2Nm).
Step 9. Manual TEST or Resetting Errors
In order to test or reset the device you must carefully remove the diffusor by unfastening the 4
mounting screws. Then push the button as described in the according paragraphs on page 1 and
2.
NOTE!! After finishing the installation you must power the luminaire at least for 24 hours
for battery charging to perform the nominal autonomy.
923939016_09_007
L1 L N
1
7
2 3
5
8
6
98
4

Page 4 from 5 923939016_09_007
Status of LEDs
Led status explanation
GREEN
YELLOW
RED
Normal
Charging
Battery duration test (auto or manual)
Battery fault
Battery fault and light source fault
Charger and battery fault (or mains off and battery fault)
Charger and light source fault (or mains off and light source fault)
Charger, battery and light source fault (or mains off, battery and light source fault)
1Hz: Heating circuit fault
5Hz: Open circuit of heating resistors
Light source test
Light source fault
Steady ON Steady OFF Flashing in 1Hz or 5Hz
Charger fault, battery not connected
or mains off
LEDs Description
The heating circuit faults are:
1) Open circuit of the heat sensor.
2) Short circuit of the heat sensor.
o
3) When the heated area is >50 C. All the above faults are indicated as long as they
exist. When they are restored, they will be erased and not indicated by the indication
LEDs.
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
45 °C max. across the board
Cable connection with non-reversible connectors
14-16.5V DC
5.4W
GR-938/30L/LT GR-939/30L/LT
0505175/30L
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)

Page 5 from 5 923939016_09_007
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.