olympia electronics GR-938/15L User manual

Thank you for purchasing this product of Olympia
Electronics. A European manufacturer.
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply. In normal operation the led
strip lights and the battery is charging. In case of
a mains power supply failure the luminaire will
light the led strip automatically in emergency
mode. When the mains power supply is
restored the device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 2.
OPERATION
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails and battery has lost its
energy. During this operation the luminaire enters
the idle state and battery consumption is
negligible, in order to be protected from deep
discharge.
Battery charging
The battery charging is completely controlled. In
this case, is achieved the perfect battery
maintenance , as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance current.
Manual Test
The manual test can be conducted only if the
main power supply and the battery is connected.
By pressing the TEST/RESET button briefly (page
2) an operation test is initiated. During this test
period all indication LEDs are OFF.
Automatic test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the main
power supply and the battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted and
measures the luminaire`s back up operation. This
test is conducted automatically every six months.
In order to be performed, the main power supply
and the battery should be connected (the battery
should be charged). If the battery is not charged,
the test is postponed until the battery is completely
charged. If during the Automatic Autonomous Test
the luminaire’s duration is lower than the named,
then the battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is stated
in the technical characteristics. During emergency
mode, a LED strip test is also performed.
Resetting Errors
Push the TEST/RESET button for 5 seconds, to
extinguish all the indicated LED errors (page 2).
Then the luminaire enters regular operation mode.
Indication LED status
(with connected mains power supply).
Charge
On: Good charge current.
Οff: No battery (No charging current or
disconnected battery).
Lamp fault
Οn: faulty LED strip.
Off: Good LED strip.
Fault
Οff: Battery OK.
WATERPROOF SELF-TESTING EMERGENCY LUMINAIRES
Page 1 from 2
220-240V AC/50-60Hz
5W / 8.5VA
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, lamp fault, fault indication LED
From overcharge and full discharge
IP 65
3.6V/3Ah
210lm / 210lm
30 white LED’s
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
0 to 40 C
o
Up to 95%
3 years (1 year for the battery)
920gr.
363 x 145 x 73 mm
3.5W / 7.5VA
3.6V/1Ah
105lm / 105lm
15 white LED’s
180min
5W /8.5VA3.5W / 7.5VA
3.6V/1.5Ah
210lm / 210lm 105lm / 105lm
30 white LED’s
210lm / 210lm
15 white LED’s
GR-938/30LGR-938/15L GR-939/15L GR-939/30L
790gr. 860gr.
923939100_09_006
High Quality European based Manufacturers

Page 2 from 2
Blink (With Charge LED ON): Autonomy or low
battery problem
(the battery must be replaced).
Blink (With Charge LED Off):
No charging current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel only.
2. The device must be connected to the mains
power supply thru a fuse dependent by the total
amount of the line’s power load.
In case of battery or lamp replacement, these
must be replaced by parts of the same type, by
the manufacturer or by a competent person.
3.
4. In case of inactive use for a period greater than
2 months, disconnect the battery by pulling out
the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be discarded
only
t i
in battery recycling points. Do not
incinerate.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained
A: Including test device
*90: 1.5 hour duration
180: 3 hour duration
NOTE!! After finishing the installation you must
power the luminaire at least for 24 hours for
battery charging to perform the named
autonomy.
9
67
Manual TEST or Resetting Errors
In order to test or reset the device you
must carefully remove the diffusor by
unfastening the 4 mounting screws.
Then push the button as described in
the according paragraphs on page 1.
1
8
10
L1 L N N
L
N
L
L1 L N L1 L N
External
switch
Controlled operation of the lamp
Link
Permanent maintained operation
1 Remove the diffusor. Place simultaneously 2 flat blade screwdrivers and pull up gently the
reflector.
2 Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the tightness isolation IP 65). Install the cable gland, pass the round cable thru and
tighten it all the way.
4 Place the battery’s connector to the corresponding connector on the P.C.B.
5 Connect the mains cables to the respective terminal block (connect the ground wire if required).
6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be connected
to an external switch to control the maintained or non maintained operation of the luminaire.
7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral and L for
live wire, and link the L and L1.
8 Install the included tie (if needed) to fasten securely the power cables.
9 Refit the reflector and fasten the two small screws (included).
10 Finaly place the diffusor by using the 4 included screws (tightening torque 1.2 Nm).
INSTALLATION INSTRUCTIONS
234
5
923939100_09_006