olympia electronics POWER LIGHT Series User manual

GENERAL o
These luminaires are used indoors (ta 40 C)
where emergency light is needed. Each
luminaire must be permanently connected to
mains power supply. In normal operation the
power indicator lights and the charge indicator
blinks to show that the batteries are in
charging condition. In case of a mains
power supply failure the power and the
charge indicators turns off and the luminaire
will light the spot lamps automatically in
emergency mode. When the mains power
supply is restored the device turns to normal
operation.
INSTALLATION
To install the luminaire follow the installation
instructions οn page 3.
OPERATION
When the device is powered from the mains,
thecharge indicator blinks and confirms the
charging of the batteries. When the batteries
are charged, it lights constantly. If it does not
light, probably, the batteries are disconnected.
If it does not light and the batteries are
connected, then contact the technician. As
long as the charge indicator blinks, the
batteries of the luminaire are charging and in
this period, any autonomy test must be
avoided. When the charging circle is
complete, the indicator lights continuously (it
can be used as an indication of a power
interruption). The batteries charging is done
by an 3 stages
technological advanced procedure, to ensure
the appropriate and full charging of the
batteries.
The power indicator confirms the proper
connection to the mains. The TEST button,
has a dual use. If pressed instantlly while the
device is connected to the mains, the device
simulates the power interruption, by lighting
the lamps for 3''. In this way,we can control
the driver circuit of the lamps and the lamps as
indicated in paragraph 3in the text below.
Dimming option
When the voltage is interrupted, with
corresponding pressings of the button, we can
choose the illumination of 100%, 50%, 33% or
turned off, either to increase the autonomy time
or not to consume the battery power
unnecessarily. This option is canceled when the
networkisrestored.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
Page 1 from 3
GRL-22``POWER LIGHT`` SERIES NON-MAINTAINED EMERGENCY LUMINAIRE
923022100_09_006
Bayblend FR3010, transparent polycarbonate
TECHNICAL CHARACTERISTICS(for LED MODULE Specs. see page 2)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Pb)
CHARGING TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
<24h
Power indicator, battery charge indicator, TEST button
From overcharge and deep discharge
IP42
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)
White LEDs
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
302 x 103 x 230 mm
220-240V AC/50-60Hz
600 min
12V/7Ah
710lm
16VA
3400gr.
Thank you for your trust in our products
Olympia Electronics - European manufacturer

Page 2 from 2
2. The device must be connected to the
mains power supply thru a fuse dependent by
the total amount of the line’s power load.
3. It is sugested to check every month the
indication LED for battery charging, and by
pushing instantly the TEST button to check
the emergency cirquit and the lamps. If the
luminaire does not light
4. It is sugested to check every 6 months the
minimum autononous duration by
disconnecting the mains power supply. Count
the time that the lamps light and in case of
less time than the minimum autonomous
duration the batteries must be replaced. If the
measured time is considerably less than the
minimum autonomous duration
The replacement of the battery and
the light source must be done using parts of
the same type, by the manufacturer or by a
competent person.
contact the installer.
contact the
installer.
5.
t i
in battery recycling
points. Do not incinerate.
Battery replacement.
It can be done only by a competent person
and after the mains interruption.
1. Follow the step 2 of the installation
procedure.
2. Disconnect the cables and remove the old
battery.
3. Connect the new battery with the same type
(step 3of the installation procedure) and place
it in the position of the old one.
4. Follow the step 5 of the installation
procedure and power the device..
In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
6. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
923022100_09_006
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non Maintained (*)
A: Including test device
G: Internally illuminated
600:10 hours duration
Note!! The installer should fill in, on the specification label,
the letter Gif the luminaire is used as a safety sign.
6X00 0AG
(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s
failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ LED
Olympia Electronics Α.Ε.
50 °C max. across the board
3011129
GRL-22
20.3-25.2V
5.46W
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc) Cable connection between main pcb and led module

Page 3 from 3 923022100_09_006
INSTALLATION PROCEDURE (For wall mounting only)
1. Install the included mounting accessories to hook the device from the mounting holes (fig. 1).
2. Unfasten the 4 mounting screws to remove the front plastic cover (fig. 1).
3. Make sure that the battery’s cables are connected to the respective poles. Black cable to (-) pole
and red cable to (+) pole.
4. Install the included cable gland or the rubber o-ring. Pass thru the mains cable and stabilize it by
fastening the cable gland. Connect the wires to the terminal blocks Lfor live wire and Νfor
neutral.
5. Refit with care the front plastic cover, by fastening the 4 mounting screws (tightening torque
1Nm).
WARNING!!
After the installation has finished, charge the batteries for at least 24 hours so as to obtain
the rated autonomous duration.
Fig.1
Mounting holes
TEST
button
Charge
indicator Power
indicator
power
Test On-off
charge
Cover retaining screws
3
4L
N
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]