olympia electronics BAU LIGHT Series User manual

923753000_09_001
Page 1 from 4
“BAU LIGHT” SERIES SELF TESTING MAINTAINED EMERGENCY LUMINARIES
220-240V AC/50-60Hz
3h
24 h
LED Charge, Battery Fault LED / Magnetic Test Contanct
IP54
3.6V/3Ah
4.6W / 4.8VA
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
up to 95%
ABS/PC, PC
763gr.
220lm / 300lm
30 LEDwhite
4W / 4.3VA
3.6V/1.5Ah
150 6lm / 1 0lm
734gr. 836gr. 807gr.
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
CHARGING TIME
INDICATIONS - CONTROLS
MINIMUM AUTONOMY DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (230V AC / emergency)
VEWING DISTANCE
ILLUMINATION SOURCE
GENERAL o
These luminaires are used indoors (ta 40 C)where
emergency light is needed.
Each luminaire must be permanently connected to mains
power supply.In normal operation the illumination LEDs are
lit as well as the green indicating charge LEDs when the
battery is charging. In case of a mains power supply failure,
the luminaire enters in emergency mode and will light
automatically. When the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation instructions on
page 3.
Battery Charging
The battery charging procedure is controlled by the
processor, this maintaining its best possible preservation, as
it extends its duration.
Battery Cut-off
The luminaire enters this mode when the mains power
supply fails and battery has lost all its energy. During this
operation the luminaire enters the idle state and battery
consumption is negligible, in order to be protected from deep
discharge.
Manual Test
This test can be done by using the A-1900 card as described
on page 2.The light source and the emergency circuit of the
device are tested. The manual test can be conducted only if
the mains power supply and the battery are connected.
Automatic Operational Test
This test includes all the operations of the manual test and is
conducted automatically every 15 days. In order to be
performed, the mains power supply and the battery should
be connected.
Automatic Autonomy Test
The Automatic Autonomy Test measures the device’s back up
operation and emergency duration. This test is conducted
automatically every 6 months. In order to be performed, the
mains power supply and the battery should be connected and
fully charged. If the battery is not fully charged, the test is
postponed until the battery is completely charged. If during
this test, the autonomy is less than nominal, the battery fault
led turns on continuously and the battery must be replaced.
Emergency Operation
The autonomy duration of battery during emergency mode is
at least 180 minutes. During emergency mode, a light source
test is also performed.
Resetting Errors
Hold the A-1900 card in TEST position for 10 to 15 seconds in
order to delete all LED indicated errors. Then the device
enters regular operation mode.
Connection to module (After request)
This luminary can be connected to any of the following
modules: Remote module, address module and fault relay
module. If you connect it to a module that supports inhibit or
rest mode, you should know that these commands can be
cancelled only during normal mode (e.g. not in emergency).
For installation refer to step 5 of the installation procedure on
page 3.
Also refer to the user manual of each module for additional
information.
Indication LED status (with connected mains power
supply).
Charge (Green LED)
On: Good charge condition.
Blink: Battery is charging.
Οff: No battery (No charging current
or disconnected battery).
Thank you for your trust in our products
Olympia Electronics - European manufacturer
3 years (1 year for the battery)
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)
358 x 85 x 88 mm358 x 125 x 88 mm 358 x 85 x 88 mm 358 x 125 x 88 mm
*15m, **17m 15m 15m *15m, **17m
GR-750/ST/HP/LL GR-751/ST/LP/LL GR-752/ST/HP/HL GR-753/ST/LP/HL

Page 2 from 4
Fault (Red LED)
Οn :Faulty LED strip (must be replaced) or emergency
circuit (must be checked by an authorized personnel).
Blink (With Charge LED ON): Autonomy or low battery
problem (the battery must be replaced).
Οff: No fault.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or testing must
be done by authorized personnel only.
2. The device must be connected to the mains power supply
through a fuse dependent by the total amount of the line’s
power load.
t i in battery
recycling points. Do not incinerate.
Test and Faults Reset operations with theA-1900 card (not
included and available after request). For lights test, you
mustplacethe cardinfront oftheTESTindicator andremove it
immediately. For Autonomy Test, you must place the card in
frontofTESTandholditfor5to10seconds.
To reset errors you must place the card in front of TEST by
holding it for 10 to 15seconds and removing it.
Only for models GR-750/ST/HP/LL and GR-751/ST/HP/HL
*15m: When the luminary is installed on a wall.
**17m: When luminary is installed on the ceiling.
3. In case of inactive use for a period greater than 2 months,
disconnect the battery by pulling out the battery’s connector.
4. I s not allowed to discard batteries in to common
trash bins, they must be discarded only
923753000_09_001
GR-753/ST/LP/HL
220-240V /50-60Hz
RATED POWER: 4.6W/4.8VA
LUMINOSITY: 300lm
BATTERY:3.6V/3Ah IP54
t40ºC
a
t º 5-40 CMADE IN GREECE
81 0
X1AF
TEST
INDICATORS
GREEN:CHARGE
RED:FAULT
A-1900

Page 3 from 4 923753000_09_001
INSTALLATION INSTRUCTIONS 2
1
3 6
5
N
N
L
L
External
switch
Link
Controled operation of the lamp
Permanent maintained operation
NN
L L
L1 L1
1 Place a flat blade screwdriver to the plastic hook and
pull up gently to release the diffusor.
2 Unfasten the 2 screws to remove the reflector.
3Use the included mounting parts to mount the base plastic.
4 Always use in any case round mains cable,with a
diameter of 5-10mm (H05RN-F type 2x1mm² or any other
type,at least equal to it’s mechanical and electrical
properties). ATTENTION!! The cable must not be deformed
in any way (This requirement is important to ensure the ΙΡ
rating). Install the included gasket in to the cable entry holes
(verify that is not deformed). Make a hole in the center by
using a small screwdriver. Pass the round cable through the
gasket. Connect the mains cables to the respective terminal
block. Ν for neutral, L for live wire and L1 for the maintained
operation. The L1 wire can be connected to an external switch
to control the maintained or non maintained operation of the
luminary.For permanent maintained operation use two wires
to power the luminary, Ν for neutral and L for live wire, and link the L and L1.
5
terminals minding the correct polarity. Depending on the module that will
be used, the cables that will be used, have different names. InA, signals +L, C are also connected,
while signals -L, NC/NO in the terminal B.
6 Place the battery’s connector to the corresponding connector on the P.C.B.
7 Refit the reflector and the diffusor (mind the correct orientation) and the luminary is ready
to operate.
In case you use a module conncect it on P.C.B. If the module needs cabling follow drill a hole in
order to pass the 2 signal cables. Install the included gasket, pass the communication cables and
connect them on the A, B
Mounting methods
BAU Light luminaries can be surface mounted on walls or ceilings. For these mounted installations, special accessories are included.
NOTE!! After finishing the installation you must power the luminaire at least for 24 hours for battery charging to perform the named
autonomy.
Wall
bottom
view
Wall installation Ceiling installation
Ceiling

Page 4 from 4 923753000_09_001
Battery replacement.
It can be done only by a competent person and after the mains supply interruption.
1. Dismantle the device (step 1 and step 2 of the installation instructions).
2. Disconnect the connector and remove the old battery.
3. Connect the new battery with the same type (step 6of the installation instructions) and
place it in the position of the old one.
4. Follow the step 7of the installation procedure and power the device.
(*) Maintained operation: The luminaire lights its illumination source, when it
is powered by the mains power supply or not.
Non Maintained operation: The luminaire lights its illumination source, only in
powersupply’sfailure.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
B: Including remote test mode
C: Including inhibiting mode
F: Automatic test gear complying
with IEC 61347-2-7 denoted EL-T
G: Internally illuminated
180: 3 hours duration
The light source contained in this luminaire shall only be replaced by the manufacturer, or his agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
WARRANTY
OlympiaElectronicsguaranteesthequality,conditionandoperationofthegoods.TheperiodofwarrantyisspecifiedintheofficialcatalogueofOlympia
Electronics and also in the technical leaflet, which accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods provided or has any repairs or re-setting
donebyathirdparty,unlessOlympiaElectronicshasfullyagreedtotheminwriting.Productsthathavebeendamagedcanbereturnedtothepremises
ofourcompanyforrepairorreplacement,aslongasthewarrantyperiodisvalid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the buyer depending on the reason of defection.
OlympiaElectronicsreservestherighttochargeornotthebuyerthetransportationcost.
HEADOFFICE
72ndkm.O.N.R.Thessaloniki-Katerini
P.C.60300P.O.Box06ΕginioPieriasGreece
www.olympia-electronics.gr
[email protected]
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
45 °C max. across the board
Non-reversible connection between main pcb and led module
14-16.5VDC
2W
2001195
GR-750/ST/HP/LL GR-751/ST/LP/LL GR-752/ST/HP/HL GR-753/ST/LP/HL
X18 0A F1
B GC
NOTE!! If a module then the installer
shouldfillin,onthespecificationlabel,thelettersBor/andC.
NOTE!! The installer should fill in, on the specification label, the letter Gif the
luminaireisusedasasafetysign.
will be used (except the fault relay module),