Omcan MS-IT-0330-C User manual

Revised - 10/14/2021
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Gear-Driven Meat Slicer
Model MS-IT-0330-C
Item 38917
Instruction Manual

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
--------------------------------------------------------------------------- 6
-------------------------------------------------------------------------------------------- 6
----------------------------------------------------------------------------------------- 6 - 7
----------------------------------------------------------------------------------- 7 - 10
---------------------------------------------------------------------------- 11 - 20
---------------------------------------------------------------------------- 21
------------------------------------------------------------------------------------------------- 22
---------------------------------------------------------------------------- 23
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
Model MS-IT-0330-C

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Safety and Warranty
ELECTRICAL SUPPLY
Check that the voltage corresponds to the label data.
1. Connect the machine to the socket.
2. Check that the blade cover fastener handle is tight screwed.
3. Check that the blade sharpener is lowered and the protective cover is closed.
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.

5
Safety and Warranty
4. Press the green pushbutton to start the blade rotation (pilot light on).
5. The blade must rotate in the counterclockwise direction.
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as
possible.
1 YEAR PARTS AND LABOR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

6
Installation
Operation
The slicer must be placed on a plane, horizontal, anti-skid and stable surface, t for carrying its weight. The
recommended height of the work top is about 800 mm. Check there are no obstacles for the product holder
stroke.
PRELIMINARY CLEANING
Clean off the protective oil from the slicer.
WARNING
The following products are not sliceable:
• Inedible products.
• Products with bones.
• Frozen products.
Check that the slicer is off and position the slice thickness control on zero.
Technical Specications
Model MS-IT-0330-C
Blade 13” / 330mm
Power 0.35 kW / 0.47 HP
Slicing Volume* 8 hours or more
Cutting Size □ 10.6” x 6.7” / 269 x 170mm
○ 9.5” / 240mm
Cut Thickness 0 - 0.6” / 0 -14mm
RPM 240
Electrical 120V / 60Hz / 1
Weight 94.8 lbs. / 43 kgs.
Packaging Weight 110 lbs. / 50 kgs.
Dimensions 26.4” x 28.7” x 20.9” / 670 x 729 x 530mm
Packaging Dimensions 32.7” x 28” x 26.7” / 831 x 711 x 678mm
Item Number 38917

7
Operation
Maintenance
HOW TO LOAD THE PRODUCT TO CUT
1. Place the product to cut against the product holder and the thickness plate sides.
2. Lay the last slice device on the product to cut, far from the slice thickness plate. The product is fed to the
slice thickness plate by gravity, this makes the cut easier.
3. Rotate the slice thickness control onto the cutting thickness you wish.
4. Press the green pushbutton to start the blade.
5. At constant speed feed the product holder to the blade stroke end then return to the operator and repeat
the operation.
6. When the work is over, pull the product holder towards the operator, press the red button to turn the blade
off and rotate the slice thickness control on zero.
HOW TO LOAD SHORT PRODUCTS (LAST SLICE)
Check that the slicer is off and position the slice thickness control on zero.
WARNING: Do not use your hands to push the products towards the blade.
1. Place the product to be cut against the wall of the product holder and the slice thickness plate.
2. Push the goods against the slice thickness plate using the last slice device.
3. Rotate the slice thickness control onto the cutting thickness you wish.
4. Press the green pushbutton to start the blade.
5. At constant speed feed the product holder to the blade stroke end then return to the operator and repeat
the operation.
6. When the work is over, pull the product holder towards the operator, press the red button to turn the blade
off and rotate the slice thickness control on zero.
BLADE SHARPENING
Whenever the cut is not satisfactory, sharp the blade. The time interval between a sharpening and the following
depends on the intensity of use of the slicer and on the kind of food you cut. Replace the blade when the
diameter becomes 10 mm less than the nominal diameter. For the replacement, ask the assistant service
closest to you.
WARNING
The replacement of the blade is dangerous operation. Should the sharpening quality be not satisfactory,
replace the stones. Contact a customer servicing.
1. Clean the blade removing any greasy residue.
2. Make sure that the machine is off.

8
Maintenance
3. Rotate the slice thickness control to zero to make sure that the blade is covered by the slice thickness
plate.
4. Lift the sharpener cover.
5. Slip off completely the sharpener and spin it 180 degrees.
6. Put the sharpener device.
7. Push the green button to start the machine.
8. Sharpening: Press the sharpening wheel for about 10-15 seconds. Then press simultaneously also the
grinding stone for two seconds. Contemporaneously loosen the two grind stones. The sharpening and
honing take place then simultaneously.
WARNING: for a suitable effect please execute sharpening for 10-15” approx.
9. Press the red stop pushbutton.
10. Lift and rotate 180 degrees the sharpener and reallocate it into its initial position. Loosen the handle
rotating it clockwise to block the sharpener. Lower the sharpener cover.
SHARPENER DEVICE REMOVAL
To facilitate the cleaning of the sharpening grinder, remove the sharpener device pulling it upwards.
WARNING: Do not immerse in water or detergent the sharpening device.
CLEANING OF THE GRINDING WHEELS
To obtain an excellent sharpening the grinding wheel must always be clean. Remove dirt and grease with
alcohol and the supplied special brush.
MAINTENANCE
Disconnect the plug from the power point and take the slice thickness control on zero. We advise to wear
protective gloves during all the cleaning and maintenance operations.
ELECTRIC CABLE CHECK
Periodically check the electric cable wear.
SPARE PARTS
In case of parts replacement, ask only original spare parts.
CLEANING
If you do not use the machine for long time, always carry out a deep cleaning of the machine before using it.
For the cleaning of all the open parts use a dampen cloth.
WARNING: Do not use water jet.

9
Maintenance
COMPONENTS REMOVAL
DANGER: During the cleaning operations be careful: danger of accident.
PRODUCT HOLDER
1. Position on zero the slice thickness control.
2. Loosen up completely the product holder clamping handle rotating it counterclockwise.
3. Pull the product holder towards the operator to block it. The metallic click means that the product holder is
clamped.
4. Lift the pusher from the guide bar.
5. Lift the product holder slipping it off from its support.
6. Clean the product holder.
IMPORTANT: The slice thickness control is clamped on zero.
SLICE DEFLECTOR
1. Loosen the xing screws and remove the slice deector.
BLADE COVER
1. Loosen the blade cover fastener handle rotating it counterclockwise.
2. Push the handle in the direction of the blade.
3. Lift the blade cover.
ATTENTION: Once removed the blade cover, an interlocking device stops the rotation of the blade.
BLADE CLEANING
DANGER: During the cleaning of the blade, be careful of any accidental contact with the blade.
1. Mop up the front side of the blade with a dampen cloth and move slowly from the centre to the edge of the
blade, as shown by the arrow in the picture.
2. Clean in the same way the back side of the blade.
3. Dry with a cloth both sides of the blade.
4. After cleaning, x the blade cover.
5. Insert the fastener and screw to block the blade cover.
Clean all the pieces in warm water and washing-up liquid. Rinse them with hot water and dry them. Assemble
the machine following in reverse the procedure described above.
GUIDES LUBRICATION
This operation must be performed after cleaning the slicer or whenever the sliding is difcult. Use oil SHELL
ONDINA 15 or ESSO MARCOL 82.

10
Maintenance
LUBRICATION OF THE GUIDE BAR OF THE PRODUCT HOLDER:
1. Drop some oil on the bar.
2. Let the last slice device slide on the guide bar.
LUBRICATION OF THE GUIDE BAR OF THE PRODUCT HOLDER CARRIAGE:
1. Push the product holder towards stroke end.
2. Lift the slicer.
3. Drop some oil on the bar.
4. Place the slicer on the work top, push the product holder to and from.

11
Parts Breakdown
Model MS-IT-0330-C 38917

12
Parts Breakdown
Model MS-IT-0330-C 38917

13
Parts Breakdown
Model MS-IT-0330-C 38917

14
Parts Breakdown
Model MS-IT-0330-C 38917

15
Parts Breakdown
Model MS-IT-0330-C 38917

16
Parts Breakdown
Model MS-IT-0330-C 38917

17
Parts Breakdown
Model MS-IT-0330-C 38917

18
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
36535 Assy Sharpener for 38917 A1036 36584 All Sharpener Cover for 38917 C1637 36654 Spacer per Registro M10 p.1x33 for
38917 D5457
17279 Ring EL.Benzing 5 for 38917 A5403 36591 Carriage Support for 38917 C185404 65614 Spacer Fixing Sharpener Cover for
38917 D5472
16902 Ring EL.Benzing 8 for 38917 A5406 36593 Assembled Carriage for 38917 C1903 65615 Foot Spacer Ø8x22x25 Front Left for
38917 D5495
17281 Ring EL.Seeger Ext.25 for 38917 A5453 65610 Cord 0.5 LG.750 Coverblade Microswitch
for 38917 C3351 65616 Foot Spacer Ø8x22x17 Front Right for 38917 D5496
77585 Ring EL.Seeger Est.25 Ser.Heavy for
38917 A5454 17316 Pin 8.5mm for 38917 C4601 65617 Foot Spacer Ø8x22x20 Back Left for 38917 D5497
19484 Ring 52 for 38917 A5485 17317 Pin.11 for 38917 C4602 65618 Foot Spacer Ø8x22x20 Back Right for
38917 D5498
19612 Ring 33 for 38917 A5495 36601 Rivet 1.9x5 for 38917 C4640 36659 Hand Grip-Knob Spacer for 38917 D575081
17283 Oil Seal 25x52x10 for 38917 A5809 36607 Blade Cover Bolt Keeper 14x14M for
38917 C5007 36661 Carriage Shock Absorber Spacer for 38917 D5762
17285 Oil Seal 60x75x8 for 38917 A5815 20458 Capacitor 20uF for 38917 C5815 60786 Locknut Spacer for 38917 D5770
19493 Oil Seal 25x47x07 for 38917 A5816 74403 Connector Faston 2 Poles Male for 38917 C6010 17345 Cam Bearing for 38917 E1458
17288 O-Ring 3081 20.24x2.62 for 38917 A5854 65611 Cover for Box S1033 Latamid for 38917 C644880 79267 Cam Eccentric Stroke mm.16 for 38917 E1489
65609 Sealing Ring Shaft for 38917 A594601 78266 Front Motor Cover for 38917 C6463 36680 Carriage Felt for 38917 F1606
17290 Carriage Bar for 38917 B1010A 36615 Series Back Motor Cover for 38917 C6466 36682 Unhook Friction Clasp 12x22x8 for
38917 F3015
60431 Complete Carriage Rail Assembly for
38917 B1080 36616 Transparent Cover for Carr. Plate for 38917 C6538 77591 Support Blade Flange for 38917 F6039
36549 Shock Absorber Rod 12x185 for 38917 B1252 36617 Motor Fan Cover for 38917 C6573 65619 Flange X Index Knob I2131 for 38917 F6088
19501 Meat Grip Rod A310 & C for 38917 B1337A 36623 Foot Cover for 38917 C6682 17351 Locknut for 38917 G5018
65883 Sliding Bar for 38917 B1736 64361 Sharpener Body for 38917 C680764 36689 Stainless Steel Locknut M8 for 38917 G5027
17298 Bushing Fastener C for 38917 B6006 36628 Switch Cover 16x20 for 38917 C7113 36691 Ring for Bushing for 38917 G5053
19618 Bushing 8x10x8 for 38917 B6009 17334 Bearing 2Z-6205 25x52x15 for 38917 C8011 36692 Ring for Cam for 38917 G5054
16904 Bushing Sharpener for 38917 B6048 16925 Bearing 2RS-6204 20x47x14 for 38917 C8024 36695 Ring Support Cap for 38917 G5055
16905 Bushing DU 16x18x15 for 38917 B6053 36630 Bearing 5x16x6.5 for 38917 C8035 36697 Logging Lock Nut for 38917 G5064
17304 Bushing for 38917 B6056 36631 Bearing 2RS-6205 25x52x15 for 38917 C8056 36698 Index Ring M10 p.1 h.17 for 38917 G5084
19630 Bushing Fastener HBC for 38917 B6104B 16926 Bearing 2RS-6000 (10x26x8) for 38917 C8067 36700 Seal for 38917 G8014
78265 Bushing Funnel for 38917 B6110 19639 Nut M8 for 38917 D0135 17354 Handle T210 for 38917 I1910
18648 Bushing for 38917 B6212 36637 Nut U5589 M8 Stainless Steel for 38917 D0135X 17356 Fastener Handle for 38917 I1926
36563 Carriage Bushing for 38917 B6213 77508 Stainless Steel Nut U5588 M12 for 38917 D014215 17363 End Grip Handle for 38917 I2040
36564 Bushing for Carriage Support lg.23mm
for 38917 B6214 66365 Domed Nut Din 917 M8 Stainless Steel for 38917 D014515 65620 Handle 28x170 Carriage Tray NSF for 38917 I205577
36566 Bushing to Hold Carriage Springs for
38917 B6221 19643 Nut M10 for 38917 D0157X 63463 Transparent Cover Knob Screw for 38917 I2090
36569 Fixing Lever Bushing for 38917 B6239 36643 Nut U5588 M5 for 38917 D0160 36717 Knob Assy for 38917 I2098
36570 Bushing DU 16x18x20 for 38917 B6246 65613 Stainless Steel Nut U5588 M4 for 38917 D016115 36719 Cover Handle for 38917 I2102
36574 Bushing for 38917 B6333 19644 Nut M6 for 38917 D0163 23632 Screw for 38917 I2103
36575 Bushing for 38917 B6334 36647 Nut U5588 M8 for 38917 D0165 65621 Knob Ø12x25 M6 for 38917 I2115
36576 Bushing DU 28x32x25 for 38917 B6335 36648 Nut U5588 M8 for 38917 D0165X 65622 Sharpener Body Knob for 38917 I2117
78677 Bushing Fastener Guard Knife C for
38917 B6398 36653 Spacer for 38917 D5413 65623 Handle Assembly NSF for 38917 I2182
Model MS-IT-0330-C 38917

19
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
65624 Impugn.Graduata Ass. for 38917 I2184 36794 Carr. Plate Lock Pivot for 38917 P3440 19674 Washer 44.5x51.5x0.2 for 38917 R6848
62453 Nylon Gear for 38917 I2403 65628 Pivot Sharpener for 38917 P3647 77540 Washer 6.2x14x0.6 for 38917 R6854
62350 Bushing Glide Dia 8x8 for 38917 I3065 79272 Knife Shaft for 38917 P3648 19675 Washer C for 38917 R6863
62351 Bushing Glide Pin Dia 8x38 for 38917 I3082 36805 Pivot for Grinding Stone for 38917 P3657 36892 Washer 17x30x4 for 38917 R6874
72282 Overload Protector for 38917 I3697 77594 Assy Driving Pivot Per T8093 for 38917 P3697 16972 Washer 5.5x19x2.5 for 38917 R6884
79578 Blade 330 57x4x286 for 38917 L0632 65629 Concave Start Button Pin for 38917 P3701 36893 Stainless Steel Special Washer 8.5x24x2
for 38917 R6897X
65626 Assy Lift Lever for 38917 L2498 65630 Convex Stop Button Pin for 38917 P3702 36897 Special Washer 5.5x22x1.5 for 38917 R6932
14787 Grinding Sharpening Stone 48x15x14.3
for 38917 M6602 36830 Flat Bar C for 38917 P4765 65641 Special Washer X Sharpener 6x25x1 for 38917 R6959
14788 Finishing Truing Stone 48x08x14.3 for
38917 M6621 36834 Index Casting C-H for 38917 P4860 61390 Thickness Dial Plate for 38917 R6966
19776 Spring 14x1.5x60 for 38917 M7032 65631 Plastic Body Sharpener for 38917 P4937 78261 Rotor Stator H.50 for 38917 R8021
19782 Spring 19.5x1.5x16.7 for 38917 M7050 17438 Foot for 38917 P5030 65642 P.C.B. Protection Box for 38917 S103380
19250 Spring 24.8x1.8x15 for 38917 M7071 65632 Sliding Bearing Flat for 38917 P5102 19680 Ball 3 17 for 38917 S3005
36746 Spring 7x0.8x23 Cam for 38917 M7076 65633 Upper Plate Hinge for 38917 P5112 17465 Ball 4.76 for 38917 S3015
19248 Spring 15.6x20x2.2 for 38917 M7120 65634 Plate for Hinge for 38917 P5114 36906 Circuit Board 120V/60 Opt.148 for 38917 S3284
36749 Carriage Bar Spring 25-28-1.5 for 38917 M7121 65635 Carriage Product Tray for 38917 P5333 36908 Track C-CD for 38917 S3815
36750 18.5x20.9x1.2 Bar Carriage Spring for
38917 M7122 65636 Assy Carriage Tray for 38917 P5678 36910 LED KL74D250 for 38917 S6506
36751 Spring for 38917 M7166 78235 End Grip for 38917 P6729 36915 Pin Stainless Steel D.6x28 for 38917 S7516
65627 Button Spring for 38917 M7182 79637 End Grip for 38917 P7019 36920 Pin 4x25 for 38917 S7526
20263 Motor 120V/60Hz-1 for 38917 M8246 65637 Special Screw M6x25 X Knob for 38917 P7475 36921 Stainless Steel 4x7 Pin M.C for 38917 S7527
19791 Oiler Oil Cap with Screw for 38917 O4040 65638 Special Screw Captive M8x44 for 38917 P7478 36931 Pin 8x50 for 38917 S7669
17388 R.Shock Absorb.12x19x2 for 38917 P1012 36857 Protection Superiore Lama for 38917 P7969 19870 Stator 120/60 for 38917 S8562
17390 Rubber Shock Abs. 16x22x2.5 for 38917 P1019 17448 Sharpener Pusher for 38917 P8601 65643 Capacitor Holder for 38917 S8866
36760 Pin Tray Shock-Absorber for 38917 P1025 65639 Assy On/Off Switch + PCB for 38917 P9507 78236 Bracket Washer C for 38917 S8951A
17392 PL.Shock Absorb.8.5x20 for 38917 P1034 65640 Oil Receiver for 38917 R1027 65644 Bracket Support for 38917 S919201
36761 Shock Absorber for 38917 P103401 19657 Washer 4 for 38917 R6003 36974 Carriage Plexi Support for 38917 S9238
19797 Nylon Shock 8.5x8 for 38917 P1042 19659 Washer 8 for 38917 R6006 36976 Support for 38917 S9402
36762 Rubber Plug for 38917 P1053 36877 Washer 8.2x16x0.9 for 38917 R6207 36977 Sharpener Support for 38917 S9448
16955 Shock Absorber for 38917 P1059 78258 Washer 30.5x46.5x0.6 for 38917 R6251 36978 Support Bracker for 38917 S9451
17395 Shock Absorber for 38917 P1081 19666 Washer for 38917 R6280 65645 Holder Blade Guard for 38917 S9452
36763 Slice Deector for 38917 P1147 36881 Washer U6593 5 (5.5x15x1.2) for 38917 R6507 65646 Bracket Tray for 38917 S9496
36767 Knife Guard with Cover Handle for 38917 P155021 20422 Washer for 38917 R6509 65647 Assy Carriage Tray Holder for 38917 S9634
36773 Ring Guard for 38917 P1666 16967 Washer U65926 for 38917 R6512 19878 Rubber Cap for 38917 T1002
77617 Strain Relief for 38917 P2009 17457 Washer U6592 6 Stainless Steel for
38917 R6512X 19883 Label Oil for 38917 T1690
60421 Electrical Conduit for 38917 P2011 36884 Washer U6592 8 Stainless Steel for
38917 R6520X 65648 Slices Counter Label Opt3 for 38917 T1776
36778 Wire-Press for 38917 P2014 36885 Washer U6592 10 Stainless Steel for
38917 R6530X 65649 Blade Cover Fastener M8x312 for 38917 T5146
36779 Core-Hitch + Nut for 38917 P2015 17458 Contact Washer for 38917 R6806 44014 Knife Cover Tie Rod (Release Knob)
for 38917 T5182
17419 Pin Truing for 38917 P322601 36889 Washer 10.5x16x1 for 38917 R6816 19900 Driving Shaft for 38917 T8092
36793 Pin.Handle for 38917 P3430 17460 Washer 34.2x46x0.5 for 38917 R6846 36999 Riding Pin (Diam.28) for 38917 T8538
Model MS-IT-0330-C 38917

20
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
79283 Shaft Pin for 38917 T9742 19697 Screw M5x16 for 38917 V6211 65654 Stainless Steel Screw U6110 M10x30
for 38917 V706915
65650 Aluminum Gauge-Plate for 38917 V313605 19699 Screw M4x25 for 38917 V6231 37088 Screw TSP AUT.U6952 4.2x16 INOX
for 38917 V708015
37013 Motor Fan MEC80 148x16 for 38917 V4014 19700 Screw M6x16 for 38917 V6240 17502 Screw M3x5.5 for 38917 V7901
37014 STEI Screw 6x20 for 38917 V6001 19702 Screw M6x25 for 38917 V6246 17503 Screw M5x13 for 38917 V7908
37016 Screw STTC U6113 M4x25 for 38917 V6008 37039 Screw TCEI U5931 M6x25 Inox for 38917 V6246X 19717 Screw M6x50 for 38917 V7917
37018 Screw STTC U6113 M6x6 for 38917 V6010 37042 Screw TCEI U5931 M8x25 for 38917 V6254 19720 Screw M6 for 38917 V7934
37019 Screw M5x20 U5923 for 38917 V6027 77630 Stainless Steel Screw TCEI U5931
M4x12 for 38917 V634415 19917 Screw BS for 38917 V7960
65651 Vite STEI U5923 M8x40 INOX for 38917 V6040 37058 Stainless Steel Screw M4x8 for 38917 V6370 16987 Special Screw M6x15 for 38917 V8020
60426 Stainless Steel Screw STEI U5923
M8x60 for 38917 V6041 37059 Stainless Steel Screw M4x14 for 38917 V6371 37102 Screw M6x20 for 38917 V8035
65652 Vite STEI U5923 M10x40 INOX for
38917 V604715 37060 Stainless Steel Screw TE U5737 M5x12 for 38917 V6403X 19920 Screw M8x30 for 38917 V8036
37023 Screw STEI U5929 M5x5 for 38917 V6065 65653 Stainless Steel Screw TE U5739 M6x12
for 38917 V6414X 37104 Threaded Stud for 38917 V8042
19691 Grub Screw M6x6 for 38917 V6066 37064 Screw TE U5739 M10x35 for 38917 V6415X 37108 Special Fixed End Screw M6x17 for
38917 V8056
19692 Screw M6x8 for 38917 V6067 37066 Screw TE U5737 M6x15 for 38917 V6421 19726 Screw M5x21 for 38917 V8059
37025 Screw STEI U5929 M6x8 for 38917 V6067X 37067 Screw TE U5739 M5x20 for 38917 V6423 37113 Screw for Carr. Index M8x25 for 38917 V8099
19695 Screw M10x30 for 38917 V6080 AI245 Stainless Steel Screw TE U5739 M8x50
for 38917 V6456X 65884 Sliding Bar Screw M14 P.1x13 CH17 for 38917 V8115
37030 Screw M12x16 U5927 for 38917 V6081 17497 Screw TSP U6109 M5x15 Stainless Steel
for 38917 V7014X 37114 Stainless Steel Screw M6x25 for 38917 V8130
37031 Screw STEI U5929 M8x16 for 38917 V6083 17498 Screw TSPEI U5933 M4x10 for 38917 V7043
Model MS-IT-0330-C 38917