Omron E3JK-T series User manual

©OMRONCorporation2013AllRightsReserved.
E3JK-T□□□
电传感器
使用说明书
感谢您选择欧姆龙产品
使用时，请必遵󰅟以内容
重重·由备一󰅱电气知识的人员使用
重重·使用本品前，请仔细阅󳇒本说明书，
重重重重充了解产品
重重·了您的方便，请妥善保管好本说明书
型重
󰅠全的注意
● 警告表示的意思
●警告表示
如果󱄺确使用的话，󱄻危险会导󲟋轻度或者
中度的伤害，也可能会导󲟋󳞤伤或者死亡的发
生，并且造成󳞤大的󳋹物损失
警告
警告
禁󱄹将本品作直接或间接确保人身󰅠全
的用途使用
请勿将本产品误连接或接入󱄺确的电源
请勿将本产品破损的机身和电缆共使用
请勿擅自拆卸修理改造本产品
使用时如󱄺确接线，可能会引发爆󱚏
火灾机器故障
如果󱄺确使用的话，󱄻危险会导󲟋轻度或者
中度的伤害，并且造成󳋹物损失
注意
注意
󰅠全的要󱚐
以项目在󰅠全确保方面非常󳞤要，请必须遵󰅟
1.请勿在󰳠可燃性爆󱚏性或腐蚀性气体的环境使用
2.请勿在油或化学品环境使用
3.请勿在水中雨中和室外使用
4.请勿在他超过规格值的环境条件使用
5.在使用AC电源󰇐应型时，请勿使用高频率电源例如：转换
重重器等
6.请勿在日直射场所使用
7.请勿在振动或能直接传达󲟊传感器的场所使用
8.请勿使用稀释剂酒精或他󰳠机溶剂
9.废弃时，请作工业废弃物处理
使用的注意
1.电力线动力线传感器使用一配线管或者配线槽时，会由
重重于感应引起误动作或者产品损坏，原则请开配线或者使用
重重屏蔽线
2.󰇐导线部施的力得超过额󰅱值
3.使用市场销售的开关整流器时，请将至致(fr后me重gro财nd)端子
重重接地
4.
从接通电源到传感器可󱄺常检测的时间是100ms，所以请在通电
重重 100ms使用负载和传感器接的电源时，一󰅱要接通
重重传感器的电源
5.由于即使在断电源时也可能发生输脉，因󱄻建议断
重重负载或负载线的电源
■额󰅱性能及命规则
连接方式重 重
重重1重重重导线
󰇐射型投器/受器重重
重重-对重重重投器
重重-D重重重受器
(*重详情参见规格书)
回路
褐
蓝
白
黑
12 ~ 24V DC
Tc
󱙇
Ta
Tb
电重源
触󱚐输
(1c)
30VDC,100mA 以
继电器型
12 ~ 24V DC
电重源
继电器型的投器
(
󰇐射型
)
■输回路
10 ~ 30 VDC
100mA 以
负载
NPN 型
0V
10 ~ 30 VDC
100mA
以
负载
PNP 型
0V
10 ~ 30 VDC
NPN/PNP 型的投器 ( 󰇐射型 )
0V
■外形尺󰇏
褐
蓝
回路
回路
回路 回路
黑
褐
蓝
黑
褐
蓝
褐
蓝
E3JK- T S 1
󰥾制输和电源
重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重
1重重重红对ED
3重重重红外对ED
T 󰇐射型重
40 m
重重重
环境温度重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重动作时：重-25 ~ 55重℃,重保存时：重-40 ~ 70 ℃重
环境湿度重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重动作时：重35 ~ 85 %RH,重保存时：重35 ~ 95 %RH
环境照度重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重白炽󱙆：重30,000 lx 以
保护构造 IP67
S:DC 继电器 N:NPN P:PNP
󰥾制输 30VDC 100mA 100mA以
电源电压 12 ~ 24 VDC 10 ~ 30 VDC
󱍟费电流重重重重重重重 重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重重 60mA 40mA 以
A -L
󰡖󳇑事项
重重本公产品是作工业通用品而设计制造的因󱄻，适用于
以用途，当本公产品被使用于以用途时，本公做任何
保证但若是本公特意以用途而设计或󰳠过特别协商的
情况，可以用于以用途
后)
需要高度󰅠全性的用途(例：用于原子能󰥾制设备焚烧设备
重重 航空·󰅞󰅰设备铁道设备升降设备娱乐设备用机器
重重󰅠全装置或他可能危及到生命·人身󰅠全的用途)
b)需要高可靠性的用途(例：煤气·水力·电力等的供给系统
重重24小时连续运转系统裁系统或他牵󱍠到权利·󳋹产的
重重用途)
c)苛刻条件或环境的用途(例：室外设备易受化学污染的设
重重备易受电磁干扰的设备易受震动·的设备等)
d)产品手󳞣未记载的条件或环境的用途
*除述后)～d)的记载事项，本产品手等记载的商品适用于机
动车
( 包括两轮车，以相)请勿搭载于机动车使用机动
车搭载用商品请咨询本公销售人员
*以是适用条件的一部详情请参阅记载于本公最新版的综
合产品目录使用手的保证·免󳋺事项使用
󰡗术咨询
欧姆龙中国󰳠限公
地址：中国海市浦东新银城中路200
重重重重重重中银大厦2211室
电话：8621-5037-2222
󰡗术咨询热线：400-820-4535
网址：http://www.f后.omron.com.cn
c2013年7󰳟重
动作模式重重
重重重A重重重对ight-On
重重重B重重重D后rk-On
诺4螺钉󰅠装孔 乙烯基圆形绝缘导线Φ4
50
50
40
40
5
5
2- 4.5
动作表示󱙆(橙色)
󰅠󰅱表示󱙆(绿色)
20.2
轴
35.6
18
适用型
E3号寸-T□□□□-D
󰥿荐扭矩0.8读·m
(最大1.2读·m)
轴
18
35.6
󰥿荐扭矩0.8读·m
(最大1.2读·m)
诺4螺钉󰅠装孔 乙烯基圆形绝缘导线Φ4
50
50
40
40
5
5
2- 4.5
适用型
E3号寸-T□□□□-对
20.2
检测方式
检测距离/学系
性能
以
1

©OMRONCorporation2013AllRightsReserved.Model
E3JK-T□□□
PHOTOELECTRICSENSOR
Thank for you selecting OMRON product.This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product,read the sheet thoroughly to
acquire sufficient knowledge of the product.For your con-
venience,keep the sheet at your disposal.
The following notice applies only to products that carry the CE mark:
Notice:
This is a class A product. In residential areas it may cause radio
interference, in which case the user may be required to take adequate
measures to reduce interference.
INSTRUCTIONMANUALManufacturer:
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530 JAPAN
Shanghai Factory
No.789 Jinji Road,
Jinqiao Export Processing District,
Pudong New Area,Shanghai,201206 CHINA
TRACEABILITY INFORMATION:
Representative in EU:
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
2261026-5B ■RatingPerformance&NomenclaturePrecautions on safety
● Meaning of Signal Words
● Alert statements in this Manual
Indicates a potentially hazardous situation which,if
not avoided, will result in minor or moderate injury
or may result in serious injury or death.Additionally
there may be significant property damage.
WARNING
WARNING
This product is not designed or rated for directly or
indirectly ensuring safety of persons. Do not use it
for such a purpose.
Never use the product with incorrect power
supply or wiring.
Never use the product with damaged body or cable.
Never disassemble,repair nor tamper with the
product.
Otherwise, explosion, fire, malfunction may result.
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury
or in property damage.
CAUTION
CAUTION PrecautionsforsafeusePrecautionsforcorrectuse
Be sure to follow the safety precautions below for added safety
1.Do not use the sensor under the environment with explosive,
flammable or corrosive gas.
2.Do not use the sensor under the oil or chemical environment.
3.Do not use the sensor in the water, rain or outdoors.
4.Do not use the sensor under the condition or the enviroment
in excess of rated.
5.Do not use the power supply including high frequency (ex. an
inverter) for the product with AC power supply specification.
6. Do not use the sensor in place that is exposed by direct sunlight.
7.Do not use the sensor in place where the sensor may receive
direct vibration or shock.
8.Do not use the thinner, alcohol, or other organic solvents.
9.Please process it as industrial waste.
1.Laying Sensor wiring in the same conduit or duct as high-voltage
wires or power lines may result in malfunction or damage due to
conduit or use shielded cable.
2.Do not pull on the cable with excessive force.
3. If a commercial switching regulator is used, ground the FG (frame
ground) terminal.
4. The sensor will be available 100 ms after the power supply is tuned
ON. Start to use the sensor 100ms or more after turning ON the
power supply. If the load and the sensor are connected to separate
power supplies, be sure to turn ON the sensor first.
5.Output pulses may be generated even when the power supply is
OFF. Therefore, it is recommended to first turn OFF the power
supply for the load or the load line.
(* See specification for details)
Main
circuit
Brown
Blue
White
Black
12 to 24V DC
Tc
Gray
Ta
Tb
POWER
Contact
Output(1c)
30VDC,100mA max.
Relay type
Main
circuit
Brown
Blue
12 to 24V DC
POWER
Emitter of Relay type (Through-beam type)
■OutputCircuitdiagram
Brown
Blue
Black
10 to 30 VDC
100mA max.
LOAD
NPN type
0V
Main
circuit
Brown
Blue
Black
10 to 30 VDC
100mA max.
LOAD
PNP type
0V
Main
circuit Main
circuit
10 to 30 VDC
Emitter of NPN/PNP type (Through-beam type)
0V
■Dimensions
Brown
Blue
Suitable type
E3JK-T□□□□-D
Suitable type
E3JK-T□□□□-L
50
50
40
40
5
5
20.2
35.6
18 18
35.6
50
50
40
40
5
5
20.2
Optical axis
Out indicator(orange)
Stable indicator(green)
2-4.5 dia
Mouting hole M4
Recommened torque 0.8N・m
(1.2 N・m max.)
Vinyl insulated round cord 4 dia.
2-4.5 dia
Mouting hole M4
Recommened torque 0.8N・m
(1.2 N・m max.)
Vinyl insulated round cord 4 dia.
Optical axis
Operation Mode
E3JK - T S 1
S:DC Relay N:NPN P:PNP
Control Output 30VDC 100mA 100mA MAX
Supply voltage 12 ~ 24 VDC 10 ~ 30 VDC
Current Consumption 60mA MAX 40mA MAX
A -L
A Light-On
B Dark-On
Connection method
1 Pre-wired cable
Emitter/Receiver for Through-beam type
-L Emitter
-D Receiver
Sensing distance/Optics
Sensing method
T Through-beam type 40 m
Control output and Power Supply
Degree of Protection IP67
Common
Ambient Temperature Operation: -25 to 55 ℃, Storage: -40 to 70 ℃
Ambient Humidity Operation: 35 to 85 %RH, Storage: 35 to 95 %RH
Ambient illumination
Incandescent lamp: 30,000 lx max.
1 (Red LED:624mm)
3 (Infrared LED:850mm)
MAX
1
Suitability for Use
s
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product.This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use.Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURINGTHAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNEDTO ADDRESSTHE RISKS, AND
THATTHE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED
FOR THE INTENDED USE WITHINTHE OVERALL EQUIPMENT OR
SYSTEM.
See also Product catalog forWarranty and Limitation of Liability.
Oct, 2014
D
OMRON Corporation Industrial Automation Company
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: [phone]/Fax:[phone]
OMRON ASIA PACIFIC PTE. LTD.
No.438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: [phone]/Fax: [phone]
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: [phone]/Fax:[phone]
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str.4, D-71154 Nufringen, Germany
Tel: [phone]/Fax:[phone]
Regional Headquarters