Omron M6 Comfort User manual

Digital Automatic Blood Pressure Monitor
Model M6 with AC Adapter
• Instruction Manual
• РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
EN
RU
IM-HEM-7001-ARU-03-03/09
5321173-3C
HEM-7001-ARU.book Page 1 Thursday, January 8, 2009 9:55 AM

2
Contents
Before using the unit
Introduction ...........................................................................3
Important Safety Information ...............................................4
1. Overview ...........................................................................6
Operating instructions
2. Preparation .......................................................................8
2.1 Installing/Replacing the Batteries..................................8
2.2 Connecting the AC Adapter ..........................................9
2.3 Setting the Date and Time ..........................................10
3. Using the Monitor...........................................................12
3.1 How to Sit Correctly When Taking a Measurement....12
3.2 Applying the Arm Cuff .................................................14
3.3 Taking a Reading........................................................18
3.4 Using the Memory Function ........................................21
4. Quick Reference Guide..................................................23
Care and maintenance
5. Handling Errors and Problems .....................................24
6. Optional Parts.................................................................26
7. Storage and Maintenance..............................................27
8. Technical Data................................................................28
9. Some Useful Information about Blood Pressure ........30
HEM-7001-ARU.book Page 2 Thursday, January 8, 2009 9:55 AM

3
EN
Introduction
The OMRON M6 is a compact, fully automatic blood pressure monitor,
operating on the oscillometric principle. It measures your blood pres-
sure and pulse rate simply and quickly. For comfortable controlled
inflation without the need of pressure pre-setting or re-inflation the
devices uses its advanced “IntelliSense” technology.
The device also stores up to 90 measurements in memory and calcu-
lates an average value based on the last three measurements. Each
measurement is stored along with the date and time of measurement.
Please read this instruction manual thoroughly before using
the unit. For specific information about your own blood
pressure, CONSULT YOUR DOCTOR.
HEM-7001-ARU.book Page 3 Thursday, January 8, 2009 9:55 AM

4
Important Safety Information
Consult your doctor during pregnancy, arrhythmia and arteriosclerosis.
Please read this section carefully before using the unit.
Warning:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
(General Usage)
• Always consult your doctor. Self-diagnosis of measurement results
and self-treatment are dangerous.
• People with severe blood flow problems, or blood disorders, should
consult a doctor before using the unit. Cuff inflation can cause
internal bleeding.
(Battery Usage)
• If battery fluid should get in your eyes, immediately rinse with plenty
of clean water. Consult a doctor immediately.
(AC Adapter Usage)
• Never plug in or unplug the power cord from the electric outlet with
wet hands.
Caution:
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury to the user or patient or damage to
the equipment or other property.
(General Usage)
• Do not leave the unit unattended with infants or persons who cannot
express their consent.
• Do not use the unit for any purpose other than measuring blood
pressure.
• Do not disassemble the unit or arm cuff.
• Do not inflate the arm cuff over 299 mmHg.
• Do not use a mobile phone, or other devices that emit
electromagnetic fields, near the unit. This may result in incorrect
operation of the unit.
• Do not operate unit in a moving vehicle (car, airplane).
HEM-7001-ARU.book Page 4 Thursday, January 8, 2009 9:55 AM

5
Important Safety Information
EN
(AC Adapter Usage)
• Use only the original AC adapter designed for this unit. Use of
unsupported adapters may damage and/or may be hazardous to the
unit.
• Plug the AC adapter into the appropriate voltage outlet.
• Do not use the AC adapter if the unit or the power cord is damaged.
Turn off the power and unplug the power cord immediately.
(Battery Usage)
• If battery fluid should get on your skin or clothing, immediately rinse
with plenty of clean water.
• Use only four “AA” alkaline batteries with this unit. Do not use other
types of batteries.
• Do not insert the batteries with their polarities incorrectly aligned.
• Replace old batteries with new ones immediately. Replace all four
batteries at the same time.
• Remove the batteries if the unit will not be used for three months or
more.
• When the batteries are replaced, you may need to reset the date
and time. If the year is flashing on the display screen, refer to “2.3
Setting the Date and Time”.
• Do not use new and used batteries together.
General Safety Precautions
• Do not inflate the arm cuff when it is not wrapped around your arm.
• Do not apply strong shocks and vibrations to or drop the unit.
• Do not take measurements after bathing, drinking alcohol, smoking,
exercising or eating.
• Do not wash the arm cuff or immerse it in water.
• Read and follow the “Important information regarding Electro
Magnetic Compatibility (EMC)” in the Technical Data Section.
• Read and follow the “Correct Disposal of This Product” in the
Technical Data Section when disposing of the device and any used
accessories or optional parts.
Save these instructions for future reference.
HEM-7001-ARU.book Page 5 Thursday, January 8, 2009 9:55 AM

6
1.Overview
1. Overview
Monitor
A. Display
B. O/I START button
C. Memory ( ) buttons
D. Date/Time ( ) setting
button
E. Battery compartment
F. A i r j a c k
G. AC adapter jack (for optional
AC adapter)
B
D
A
C
E
G
F
HEM-7001-ARU.book Page 6 Thursday, January 8, 2009 9:55 AM

7
1.Overview
EN
Display
Package contents
H. Systolic blood pressure
I. Diastolic blood pressure
J. Memory display
K. Average value display
L. Movement error display
M. Irregular heartbeat display
N. Battery low display
O. Heartbeat display
P. Pulse display
Q. Deflation display
R. Date/Time display
S. Arm cuff (Medium cuff: arm
circumference 22-32 cm)
T. A i r p l u g
U. Air tube
V. Storage case
W. Four “AA” alkaline (LR6)
batteries
X. AC Adapter
H
O
Q
I
K
M
L
J
P
R
N
S
W
UT
V
X
HEM-7001-ARU.book Page 7 Thursday, January 8, 2009 9:55 AM

8
2.Preparation
2. Preparation
2.1 Installing/Replacing the Batteries
1. Remove the battery cover.
2. Insert four “AA” batteries as indi-
cated in the battery compartment
and then replace the battery cover.
Notes:
• If the battery low display ( ) appears on the display, replace
all four batteries at the same time. Long-life alkaline batteries
are recommended.
• Remove the batteries if the monitor will not be used for three
months or more.
• If the batteries are removed for a long period of time, the
Date/Time setting will need to be reset. See “Setting the Data
and Time” for details.
• Dispose of batteries according to applicable local regulations.
HEM-7001-ARU.book Page 8 Thursday, January 8, 2009 9:55 AM

9
2.Preparation
EN
2.2 Connecting the AC Adapter
Insert batteries into the battery compartment even when using
the AC adapter.
Notes:
• Never unplug the power cord with wet hands.
• Use only the original AC adapter designed for this unit. Use of
unsupported adapters may damage the unit.
• When storing the optional AC adapter with the main unit, be
careful not to damage the main unit or cuff.
1. Insert the AC adapter plug into the AC adapter jack on the rear
side of the main unit.
2. Plug the AC adapter into an electrical outlet.
To disconnect the AC adapter, unplug the AC adapter from the
electrical outlet first and then immediately remove the AC
adapter plug from the main unit.
1
2
Power plug
AC adapter jack
AC adapter plug
AC adapter
HEM-7001-ARU.book Page 9 Thursday, January 8, 2009 9:55 AM

10
2.Preparation
2.3 Setting the Date and Time
Your blood pressure monitor automatically stores up to 90
measurements values in its memory and calculates an average
reading based on the measurements from the last three read-
ings.
• Set the monitor to the correct date and time before taking a
measurement for the first time.
• If the batteries have been removed for a long period of time,
the date and time setting will need to be reset.
1. When the batteries are installed, the
year digits will flash in the display
when you turn on the monitor.
Note: If you need to reset the date
and time for some reason,
hold down the button while the power is off.
2. Press the button to advance
the digits one at a time.
To change the digits to a lower
number, press the button to
lower the digits one at a time.
If you hold down the or
button, the digits will advance (or
lower) rapidly.
3. Press the button to confirm the
setting when the desired number
appears on the display.
HEM-7001-ARU.book Page 10 Thursday, January 8, 2009 9:55 AM

11
2.Preparation
EN
4. Repeat steps 2 and 3 to set the month and date (day).
5. Repeat steps 2 and 3 to set the hour and minutes for the time.
6. Press the O/I START button when
you have finished setting the date
and time.
or
or
or
or
HEM-7001-ARU.book Page 11 Thursday, January 8, 2009 9:55 AM

12
3.Using the Monitor
3. Using the Monitor
3.1 How to Sit Correctly When Taking a Measurement
You can take a measurement on either your left or right arm.
Notes:
• Measurements should be taken in a quiet place and you
should be in a relaxed, seated position. Make sure that the
room is not too hot or cold.
• Avoid eating, smoking, or exercising for at least 30 minutes
before taking a measurement.
• Do not move or talk during measurement.
Correct
Posture
Remove tight fitting clothing from
your upper arm, and any thick
clothing such as a sweater.
Do not place the cuff over thick
clothes and do not roll up your sleeve
if it is too tight.
Sit upright
with your
back straight.
Place your arm on a table so
that the cuff will be at the same
level as your heart.
The gap between the
chair and the top of the
table should be between
25cm to 30cm.
HEM-7001-ARU.book Page 12 Thursday, January 8, 2009 9:55 AM

13
3.Using the Monitor
EN
Notes:
• Correct posture during measurement is necessary to get
accurate results.
• You should also try to measure your blood pressure at the
same time each day. (Within 1 hour after waking up is
recommended.)
Incorrect Posture
These situations could lead to higher blood pressure values due to
strain or the arm cuff being lower than the heart.
If the arm cuff is at a lower position than your heart use cushions
etc., to adjust the height of your arm.
•Arched back (leaning
forwards)
•Sitting cross-legged
•Sitting on a sofa or at a low
table so that you tend to lean
forward
HEM-7001-ARU.book Page 13 Thursday, January 8, 2009 9:55 AM

14
3.Using the Monitor
3.2 Applying the Arm Cuff
You can wrap the cuff either on your right or left arm.
• Remove tight-fitting clothing from
your upper arm.
• Do not place the cuff over thick
clothes and do not roll up your
sleeve if it is too tight.
• You can take a measurement on
either your left or right arm. The
blood pressure can differ between the right arm and the left
arm and therefore also the measured blood pressure values
can be different. Omron recommends to always use the same
arm for measurement. If the values between the two arms dif-
fer substantially, please check with your doctor which arm to
use for your measurement.
1. If the cuff is assembled correctly, the
hook material will be on the outside of
the cuff loop and the metal D-ring will
not touch your skin.
Note: If the cuff is not assembled,
pass the end of the cuff furthest
from the tubing through the
metal D-ring to form a loop. The smooth cloth should be
on the inside of the cuff loop.
Pile side material
Sewn hook material
D-ring
HEM-7001-ARU.book Page 14 Thursday, January 8, 2009 9:55 AM

15
3.Using the Monitor
EN
2. Insert the air plug into the air jack (on the left side of the
device).
The cuff must be fully deflated when it is inserted into the air
jack.
3. Sit on a chair with your feet flat on the floor and place your arm
on a table so that the cuff will be at the same level as your
heart.
Air plug
Air jack
HEM-7001-ARU.book Page 15 Thursday, January 8, 2009 9:55 AM

16
3.Using the Monitor
4. Put your arm through the cuff loop.
The bottom of the cuff should be approximately 1 to 2 cm
above the elbow.
Apply the cuff to your upper arm so that the coloured marker is
centred on the middle of your inner arm and points down the
inside of the arm. The air tube should run down the inside of
your forearm and be in line with your middle finger.
5. Pull the cuff so that the top and bot-
tom edges are tightened evenly
around your arm.
Bottom Edge 1 to 2 cm
Air tube
Marker
HEM-7001-ARU.book Page 16 Thursday, January 8, 2009 9:55 AM

17
3.Using the Monitor
EN
6. When the cuff is positioned correctly,
close the fabric fastener FIRMLY.
Notes:
• Make certain the cuff fits snugly around your arm.
• The cuff should make good contact with your skin. You should
be able to fit your index finger between the cuff and your arm
easily, so you can pull the cuff off and on.
• Make sure that there are no kinks in the air tubing.
Taking measurements on the right arm
Please note the following points
when applying the cuff to your right
arm. Apply the cuff so that the air
tube is at the side of your elbow.
Notes:
• Be careful not to rest your arm on the air tube, or otherwise
restrict the flow of air to the cuff.
• Apply the arm cuff so that no part of the cuff is positioned over
the elbow joint. The cuff should be 1 to 2 cm above the elbow.
HEM-7001-ARU.book Page 17 Thursday, January 8, 2009 9:55 AM

18
3.Using the Monitor
3.3 Taking a Reading
1. Press the O/I START button and remain still, the cuff will start
to inflate automatically.
As the cuff begins to inflate, the monitor automatically deter-
mines your ideal inflation level. Remain still and do not talk until
measurement is completed.
Note: Do not inflate the cuff if it is not wrapped around your
arm.
2. Inflation stops automatically
and measurement is started.
As the cuff slowly deflates,
decreasing numbers appear
on the display and the Heart-
beat symbol ( ) flashes at every heartbeat.
In rare circumstances, the monitor might re-inflate the cuff to
continue with the measurement.
3. When the measurement is complete, the arm
cuff completely deflates and your blood pres-
sure and pulse rate are displayed.
Note: The monitor automatically stores the
blood pressure readings and pulse rate
along with date and time of measurement in its memory.
HEM-7001-ARU.book Page 18 Thursday, January 8, 2009 9:55 AM

19
3.Using the Monitor
EN
4. Press the O/I START button to turn
the monitor off.
Note: If you forget to turn the moni-
tor off, it will automatically
shut itself off after five minutes.
Important:
• Wait 2-3 minutes before taking another blood pressure meas-
urement. Waiting between readings allows the arteries to
return to the condition prior to taking the blood pressure
measurement.
• If you move during measurement, the movement symbol
( ) may appear. Repeat the measurement and remain still
until the measurement is complete.
• Your blood pressure monitor includes an irregular heartbeat
feature. Irregular heartbeats can influence the results of the
measurement. The irregular heartbeat algorithm automatically
determines if the measurement is usable or needs to be
repeated. If the irregular heartbeat symbol ( ) is shown
after your have taken a measurement, repeat the measure-
ment. If the irregular heartbeat symbol ( ) is shown fre-
quently, please make your doctor aware of it.
Instructions for special conditions
If your systolic pressure is known to
be more than 220 mmHg, after the
cuff starts to inflate, press and hold
the O/I START button until the moni-
tor inflates 30 to 40 mmHg higher
than your suspected systolic pressure.
Important:
• The monitor will not inflate above 300 mmHg.
• Do not apply more pressure than necessary.
HEM-7001-ARU.book Page 19 Thursday, January 8, 2009 9:55 AM

20
3.Using the Monitor
What is Irregular Heartbeat?
An irregular heartbeat is a heartbeat
rhythm that varies by more than 25%
from the average heartbeat rhythm
detected while the unit is measuring
the systolic and diastolic blood pres-
sure.
If such an irregular rhythm is detected
more than twice during measure-
ment, the irregular heartbeat symbol
( ) appears on the display when the measurement results are dis-
played with the measurement results.
What is Arrhythmia?
A heartbeat is stimulated by electrical signals that cause the heart to
contract.
Arrhythmia is a condition where the heartbeat rhythm is abnormal due
to flaws in the bio-electrical system that drives the heartbeat. Typical
symptoms are skipped heartbeats, premature contraction, an abnor-
mally rapid (tachycardia) or slow (bradycardia) pulse. This can be
caused by heart disease, aging, physical predisposition, stress, lack of
sleep, fatigue etc. Arrhythmia can only be diagnosed by a doctor
through a special examination.
Whether the appearance of irregular heartbeat symbol ( ) in the
results indicates arrhythmia or not can only be determined by an exam-
ination and diagnosis by your doctor.
Warning:
If the irregular heartbeat symbol ( ) is shown frequently, please
make your doctor aware of it. Conducting self-diagnosis and
treatment based on measurement results is dangerous. Be sure
to follow the instructions of your doctor.
N
orma
l
H
eart
b
eat
Irregular Heartbeat
Pulse
Blood pressure
Blood pressure
Short Long
Pulse
HEM-7001-ARU.book Page 20 Thursday, January 8, 2009 9:55 AM