Omron XS5 T Series User manual

Industrial Ethernet Connectors XS5@-T / XS6@-T 1
Industrial Ethernet Connectors
XS5@-T / XS6@-T
Support for Ethernet/IP, EtherCAT, and
Other Popular Networks Based on Ethernet
• Combines tough RJ45 Connectors for use outside of panels and
Environment-resistance Connectors with IP67 protection (M12).
• M12 Smartclick mates with any threaded M12 socket and
provides 'twist and click' connection with XS5P-T panel socket.
• M12 Smartclick connectors are shielded to protect against EMI.
• Separate RJ45 assembly connectors are available for easy wiring
on site.
• Uses AWG22 Cat5E cables that are suitable for wiring outside of
panels.
TM
■Specifications
■Materials and Finish
Connector Cable
Note: is a registered trademark of the OMRON Corporation.
Type Cable with Connector
on One End (M12)
Cable with Connectors
on Both Ends (M12/M12)
Cable with Connectors on
Both Ends (M12/RJ45)
Cable with Connectors on
Both Ends (RJ45/RJ45)
RJ45 Assembly
Connector
M12 Connector for
Panel Mounting
Item / Model XS5H-T421-@M0-K XS5W-T421-@M2-K XS5W-T421-@MC-K XS5W-T421-@MD-K XS6G-T421-1 XS5P-T42@-5
Rated current 3 A 2.5 A 3 A
Rated voltage 30 V
Contact resistance 20 mΩmax.
Insulation
resistance
500 MΩ min.
Withstand voltage 1,000 VAC for 60 s (leak current: 1 mA max.)
Ambient operating
temperature
− 25 to 70°C − 40 to 70°C − 25 to 70°C
Ambient storage
temperature
− 25 to 70°C − 40 to 70°C − 25 to 70°C
Degree of
protection
M12: IEC IP67, RJ45: IEC IP20
Item Model M12 RJ45
Contact Block PBT plastic (UL94V-0),
light gray
PA plastic (UL94V-0),
black
Contacts Materials Phosphor bronze
Finish Nickel base, 0.4-μm
gold-plating
Nickel base, 1.4-μm
gold-plating
Fixtures Nickel-plated zinc alloy —
Cover PBT —
O-ring Rubber —
Specifications UL CM PVC (double shielding) Cat. 5E
Cores and colors AWG22 (0.26/7):
Yellow, orange, white, and blue
Outer Diameter 6.5 mm
Sheath color Light blue
TM

2Industrial Ethernet Connectors XS5@-T / XS6@-T
4-Pin Connectors with Cable Attached
■XS5H - Plug on One Cable End
Dimensions (Unit: mm)
Ordering Information
Note: Ask your OMRON representative about other specifications.
Model Number Legend
Use this model number legend to identify products from their model number.
When ordering, use a model number from the table in Ordering Information.
1. Type
H: Connector connected to cable, M12 plug on one cable end
2. Signal type
T: Ethernet
3. Connector Poles
4: 4 poles
4. Contact Plating
2: 0.4-μm gold plating - M12 connectors
5. Cable Connection Direction
1: Straight
6. Cable Length
A: 0.3 m G: 5 m
B: 0.5 m J: 10 m
C: 1 m K: 15 m
D: 2 m
E: 3 m
7. Connections
M: AYellow, BWhite, COrange, DBlue
(Numbers inside circles are terminal numbers)
8. Connectors on One End/Both Ends
0: One M12 Plug
9. Cable Specifications
K: UL CM PVC (double shielded) / Cat.5E
Type Cable length L (m) Model
Straight
Cable with Connector on One End
(M12)
0.5 XS5H-T421-BM0-K
1XS5H-T421-CM0-K
2XS5H-T421-DM0-K
3XS5H-T421-EM0-K
5XS5H-T421-GM0-K
10 XS5H-T421-JM0-K
15 XS5H-T421-KM0-K
XS5H-T421-@M0-K (1 x M12)
TM
1
43
2
44.7
L (cable length)
D - Coding M12
14.9 dia.
XS5H - T421- @M@-K
123456789

Industrial Ethernet Connectors XS5@-T / XS6@-T 3
■XS5W - Plugs on Both Cable Ends
Dimensions (Unit: mm)
Ordering Information
Dimensions (Unit: mm)
Ordering Information
Note: Ask your OMRON representative about other specifications.
Type Cable length L (m) Model
Straight
Cable with Connector on Both Ends
(M12 / M12)
0.5 XS5W-T421-BM2-K
1XS5W-T421-CM2-K
2XS5W-T421-DM2-K
3XS5W-T421-EM2-K
5XS5W-T421-GM2-K
10 XS5W-T421-JM2-K
15 XS5W-T421-KM2-K
Type Cable length L (m) Model
Straight
Cable with Connector on Both Ends
(M12 / RJ45)
0.3 XS5W-T421-AMC-K
0.5 XS5W-T421-BMC-K
1XS5W-T421-CMC-K
2XS5W-T421-DMC-K
3XS5W-T421-EMC-K
5XS5W-T421-GMC-K
10 XS5W-T421-JMC-K
15 XS5W-T421-KMC-K
XS5W-T421-@M2-K (2 x M12)
TM
1
43
2
44.7 44.7
L (cable length)
M12 M12
14.9 dia. 14.9 dia.
D - Coding
XS5W-T421-@MC-K (1x M12 and 1x RJ45)
TM
1
43
2
44.7 54.7
L (cable length)
RJ45
M12
14.9 dia.
D - Coding

4Industrial Ethernet Connectors XS5@-T / XS6@-T
Dimensions (Unit: mm)
Ordering Information
Note: Ask your OMRON representative about other specifications.
Model Number Legend
Use this model number legend to identify products from their model number.
When ordering, use a model number from the table in Ordering Information.
1. Type
W: Connector connected to cable, plugs on both cable ends
2. Signal type
T: Ethernet
3. Connector Poles
4: 4 poles
4. Contact Plating
2: 0.4-μm gold plating - M12 connectors
1.4 μm gold plating - RJ45 connectors
5. Cable Connection Direction
1: Straight
6. Cable Length
A: 0.3 m G: 5 m
B: 0.5 m J: 10 m
C: 1 m K: 15 m
D: 2 m
E: 3 m
7. Connections
M: AYellow, BWhite, COrange, DBlue
(Numbers inside circles are terminal numbers)
8. Connectors on One End/Both Ends
2: Two M12 Plugs
C: One M12 Plug + One RJ45 Plug
D: Two RJ45 Plugs
9. Cable Specifications
K: UL CM PVC (double shielded) / Cat.5E
Type Cable length L (m) Model
Straight
Cable with Connector on Both Ends
(RJ45 / RJ45)
0.3 XS5W-T421-AMD-K
0.5 XS5W-T421-BMD-K
1XS5W-T421-CMD-K
2XS5W-T421-DMD-K
3XS5W-T421-EMD-K
5XS5W-T421-GMD-K
10 XS5W-T421-JMD-K
15 XS5W-T421-KMD-K
XS5W-T421-@MD-K (2 x RJ45)
54.754.7
L (cable length)
RJ45RJ45
XS5W - T421- @M@-K
123456789

Industrial Ethernet Connectors XS5@-T / XS6@-T 5
Assembly Connector - RJ45
■XS6G - Plugs
Dimensions (Unit: mm)
Ordering Information
4-Pin Panel-mount Connectors
■XS5P - Sockets
Dimensions (Unit: mm)
Ordering Information
Type Cable length L (m) Model
Straight
RJ45 Assembly Connector - - - XS6G-T421-1
Type Cable length L (m) Model
Straight
M12 Connector for Panel Mounting Rear Locking 0.5 m XS5P-T426-5
Front Locking 0.5 m XS5P-T427-5
XS6G-T421-1
52.6
11.8 11.3
8.1
Contact 3
Contact 2
Contact 6 Contact 1
Applicable wires
6.1 to 6.9 dia.
Stranded wires: AWG22 to AWG24
Solid wires: AWG22 to AWG23
XS5P-T42@-5 (Rear or Front locking M12 socket)
20
18
13.9 dia.
22.1
10.5 2.5
2.8
PG9 500
10±3 (20)
17
18
Yellow
Blue
White
Orange
M12
D - Coding
15.3
Panel thickness (t)
= 1 to 4
dia.
+0.1
0
XS5P-T427-5 (Front Locking)
17
18 14.6 dia.
2.8
PG9
500
22.1
11.9
10±3 (20)
20
18
White
Yellow
Blue
Orange
2.5
M12
D - Coding
Wiring
Terminal No. Color
1Yellow
2 White
3 Orange
4Blue
XS5P-T426-5 (Rear Locking)
Panel Cutout Dimension
Note 1: The panel cutout dimen-
sion is the same for
Front-locking and Rear-
locking Connectors.
Note 2: Rotational positioning is
not possible for connec-
tor rotation.

6Industrial Ethernet Connectors XS5@-T / XS6@-T
Precautions
■Correct Use
Do not use the Connectors in an atmosphere or environment that
exceeds the specifications.
Connector Connection and Disconnection
• When connecting or disconnecting Connectors, be sure to hold the
Connectors by han
d.
•Do not hold the cable when disconnecting Connectors.
• When mating Connectors, be sure to insert the plug all the way to
the back of the socket before attempting to lock the Connectors.
•Do not use tools of any sort to mate the Connectors. Always use
your hands. Pliers or other tools may damage the Connectors.
Wiring
•Lay the cables so that external force is not applied to the
Connectors. Otherwise, the degree of protection (IP67) may not
be achieved.
Degree of Protection
•The degree of protection of Connectors (IP67) is not for a fully
watertight structure. Do not the Connectors underwater.
•
Do not step on or place any objects on the Connectors. Doing so
may damage the Connectors
.
■General Precautions
• Do not pull excessively on the Connectors or cables. Do not instal l
the Connectors or cables in any way that would place a load
directly on the mating section or cable
connections. Doing so can
damage the Connectors or break the wires inside the cables.
•Install the Connectors and cables where they will not be stepped
on to prevent the wires inside
the cables from being broken and to
prevent the Connectors from being damaged. If the Connectors or
cables must be installed where they might be stepped on, protect
them with covers.
•Refer to the specifications for your cables before bending the
cables and do not bend them past their minimum bending radius.

Industrial Ethernet Connectors XS5@-T / XS6@-T 7
MEMO

8Industrial Ethernet Connectors XS5@-T / XS6@-T
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.components.omron.com
Cat. No. G019-E-01 Printed in USA
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
11/10 Specifications subject to change without notice
All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which
can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.