Omron SC20G2 User manual

SNMP/Web Card SC20G2
Operation Manual
Detailed setting
 This document contains the information you need for using safely SNMP / Web card. Please read carefully
before installation and use.
 Please keep it at hand carefully so that you can refer to it at any time, when this book is required.

The copyright of this book belongs to OMRON SOCIAL SOLUTIONS Co.,Ltd.To copy,reproduce and reprint
the contents partially oron the whole without notice to our company is refused firmly.

The contents of this document are subject to change without notice .

About a picture, it may differ from the newest thing in part.
Windows and other names are the registered trademarks of U.S. Microsoft Corporation in the U.S. and
other countries.
 Each other company names and each company product name are the trademarks or registered trademarks of each
company.
©OMRON SOCIAL SOLUTIONS CO.,LTD. 2014-2019.All Rights Reserved.

Introduction
Thank you for purchasing the OMRON SNMP/Web card lately
■Corresponding model
• This product is equipment which makes network connection possible by inserting in the slot
of the OMRON uninterruptible power supply (UPS).
■Functional feature
• By inserting this product in an uninterruptible power supply (UPS), status acquisition from
an uninterruptible power supply (UPS) and command issue to an uninterruptible power
supply (UPS) are enabled.
• By inserting this product in an uninterruptible power supply (UPS), an uninterruptible power
supply (UPS) is manageable even from the personal computer which does not carry a
serial port.
■Offer of automatic shutdown software
• Automatic shutdown software is enclosed by this product. (Please look at the newest
information by our homepage.)
• It is possible to shut down by setup in the following cases.
When a main power supply system is downed
When the battery of an uninterruptible power supply (UPS) falls
When the connection capacity of an uninterruptible power supply (UPS) exceeds
When the temperature of an uninterruptible power supply (UPS) rises
• Automatic shutdown software and a script shutdown can perform schedule operation.
• A computer can be safely suspended by automatic shutdown software and script shutdown.
■License for automatic shutdown software
• You can use this product for two or more computers which perform shutdown via a network
by installing it.
■About export of this product
When you wish issue of parameter sheet, please apply to our homepage.
.[Homepage address]
https://www.oss.omron.co.jp/ups/support/export.html
In the caseof an inquiry, the serial number of this product is required.
I have indicated the serial number (S/N) on the seal of pasting at the container box side or the main
part base back.
i

Table of contents
Detailed setting...............................................................................................................................................1
1. Management by a web browser............................................................................................................2
1.1 How to use the setting screen .........................................................................................................2
1.2 [UPS Monitoring] Menu....................................................................................................................3
1.3 [UPSManagement] Menu..............................................................................................................12
1.4 [SNMP/WebCardManagement] Menu..........................................................................................30
1.5 [UPSHistory] Menu........................................................................................................................64
2. Power management UPS.....................................................................................................................66
2.1 Power supply state of a SNMP/Web card ...................................................................................66
2.2 Shutdown Immediately...................................................................................................................67
2.3 UPSRestart....................................................................................................................................69
2.4 The shutdown at the time of an abnormal condition......................................................................71
2.5 Schedule shutdown........................................................................................................................73
2.6 Setting of remote shutdown...........................................................................................................76
3. Management by SNMP........................................................................................................................80
3.1 Access control of a SNMP/Web card............................................................................................80
3.2 A setup of an SNMP trap addressee.............................................................................................80
3.3 SNMP manager's setup.................................................................................................................80
4. The monitor of the log by a JAVA applet.............................................................................................81
4.1 Feature..........................................................................................................................................81
4.2 The display of a monitoring screen................................................................................................81
4.3 Details of a UPS data log screen...................................................................................................82
4.4 Details of a UPS extended history log screen...............................................................................83
5. Setup of security..................................................................................................................................84
6. Reference data.....................................................................................................................................85
6.1 Specification...................................................................................................................................85
6.2 Upgrade of a firmware file..............................................................................................................87
6.3
Configuration file read-out, edit, and writing of SC20G2 ....................................................................90
1

1. Management by a web browser
1.1. How to use the setting screen
Display procedure of setting screen
1
Please start a web browser.
2
Please input the IP address of a SNMP/Web card into an address bar.
(Example: When an IP address is 192.168.2.150)
About the setting method of the IP address of a SNMP/Web card,
Please refer to "3.3 Network Configuration Method 2 :via
Telnet " or " 3.2 Network Configuration Method 1: via serial
port “of installation section in operation manual.
3
The screen for a setup of a SNMP/Web card is displayed.
In order to check the detailed information of each screen, click [Help] under a screen.
Please click the menu of the upper part and left-hand side to check other setting items.
2

1.2. [UPS Monitoring] Menu
・The information about an uninterruptible power supply (UPS) is displayed.
・The user can browse all those sub menus by read-only.
[Main Page] Menu
・The basic operating state of the present uninterruptible power supply (UPS) is displayed
by list.
・In order to set up the update time of this screen, please carry out by [SNMP/Web card
management] -[SNMP/Web card configuration] - [Page Refresh Rate (Sec)].
3

The detail description of a screen
1. UPS Model
The Model of an uninterruptible power supply (UPS) is displayed.
Example:BN150S Etc.
2. UPS Status
The present operating state of an uninterruptible power supply
(UPS) is displayed as follows.
• On Line
An input power source state is normal and is in the state
currently operated normally.
• Standby
It is in the state after a shutdown. An input power source is
normal.
• UPS Power Off
The uninterruptible power supply (UPS) is turned off.
• Bypass
It is a state that is output in bypass operation. Operating
status only uninterruptible power supply (UPS) of the
regular Inverter type
• Backup
It is a state that is moved to the backup operation by
input power failure.
• Test
It is a function test or battery test.
• UPS Fail
This is a state in which some abnormality is detected in
uninterruptible power supply (UPS).
• UPS not Found
SNMP / Web card cannot communicate with the
uninterruptible power supply (UPS).
3. UPSTemperature (℃)
Displays the temperature of internal uninterruptible power
supply (UPS).
4. UPS Manufacture
"OMRON" is displayed.
5. OutletA/B/C(Control)(sec)
Display the used time of each output of the uninterruptible
power supply (UPS).
6. InputFrequency
The present input frequency is displayed.
7. OutputFrequency
The present output frequency is displayed.
8. UPS Type
The power supply system of the uninterruptible power supply
(UPS) is displayed as one of the [Regular] or [Regular Inverter].
Uninterruptible power supply line interactive type (UPS) will be
displayed at [Regular].
9. InputVoltage
The present input voltage is displayed.
10. OutputVoltage
The present output voltage is displayed.
11. OutputLoad
The present connection capacity is displayed.
4

12. UPS latest abnormality
Last abnormality of UPS and time are displayed.
13. ACK
Recovery notice of UPS last abnormality is issued by SNMP,
Syslog, Mail.
14. UPS Next Off Time
The schedule of the next uninterruptible power supply (UPS)
power supply Off by schedule operation setup is displayed.
15. UPS Next On Time
The schedule of the next uninterruptible power supply (UPS)
power supply On by schedule operation setup is displayed.
16. SNMP/Web Card Firmware Revision
It is a version of firmware.
17. SNMP/Web Card System Date
A system date setup of a SNMP/Web card is displayed.
18. SNMP/Web Card System Time
A system time setup of a SNMP/Web card is displayed.
19. SNMP/Web Card Up Time
The total operating time after a SNMP/Web card starts is
displayed.
5

[Parameters] Menu
・Each state of the input power, output power and a battery of the present uninterruptible
power supply (UPS) is displayed.
・This page is automatically updated in [Page Refresh Rate (Sec)] time which can be set
up at [SNMP/Web card management].
6

The detail description of a screen
[OutputParameters]
1. OutputSource
The source of output power is displayed in the following state. [on
line], [bypass], [battery],[no output]
2. OutputFrequency
The present output frequency is displayed.
3. OutputVoltage
The present output voltage is displayed.
4. OutputLoad
The connected-load capacity of the present uninterruptible power
supply (UPS) is displayed by “%”.
[InputParameters]
1. InputVoltage
The present input voltage is displayed.
2. Max.Input Voltage Last 1 minute
The maximum input voltage for 1 minute to this time is
displayed.
3. Min.Input Voltage Last 1 minute
The minimum input voltage for 1 minute to this time is
displayed.
4. InputFrequency
The present input frequency is displayed.
[BatteryParameters]
1. BatteryStatus
The state of a battery is displayed by the following contents.
[ Normal],[Battery Low],[Discharging],[Battery aging],[Not
Connected]
2. Time sinceon BatteryPower
The time which is operating by battery power is displayed.
3. BatteryCapacityRemaining
The remaining battery capacity of the present to a full charge
state is displayed.
4. CurrentBatteryVoltage
The voltage of the present battery is displayed.
5. UPSTemperature(℃)
The temperature inside an uninterruptible power supply (UPS)
is displayed.
6. BatteryLast ReplacedDate
It is the date which started (exchange) to use the battery of the
uninterruptible power supply (UPS).
When battery exchange is
newly performed, please reset up on a [SNMP/Web card
management]-[SNMP/Web card configuration] screen.
7

[UPS Outlet Information] Menu
・The time chart to the uninterruptible power supply (UPS) shutdown set up by a
shutdown setup and an uninterruptible power supply (UPS) outlet control function can
be displayed according to an each outlet.
・Overall operation of each outlet is checked with this chart.
The detail description of a screen
1. UPSOutletInformation The time chart according to outlet is
displayed. This screen is only a display.
8

[Alarm Table] Menu
・The state of alarm (buzzer) is displayed.
・This page is automatically updated in [Page Refresh Rate] time which can be set up by
a [SNMP/Web card configuration].
The detail description of a screen
1. NumberofActiveAlarms
The number of factors with which the present alarm is sounded
is displayed.
2. AlarmTime
The time that each alarm was sounded.
Display time follows a setup of a SNMP/Web card.
3. Alarm Description
It is a factor of sounding the alarm.
For the past alarms, it is stored in the log.
9

[Client Table] Menu
・The information about the client and server on the network where automatic shutdown
software is operating is displayed by list
・A client is the computer which the shutdown agent is operating and is registered on the
SNMP/Web card. If the IP address of the uninterruptible power supply (UPS) is set to
automatic shutdown software, registration will be performed automatically.
The detail description of a screen
1. ConnectedClientNumber
It is the number of clients under present operation.
2. IPAddress
It is an IP address of a client.
3. ClientName
It is a computer name of a client.
4. ShutdownDelay
It is processing time required in order to terminate the application
set as the shutdown of a client. Please refer to the [uninterruptible
power supply (UPS) management]-[shutdown setting] for the time
setting of a shutdown.
5. ConnectedTime
The time when a client registered into the SNMP/Web card is
displayed.
6. Outlet
Displays the outlet of the uninterruptible power supply (UPS) to
which the client is connected.
10

[Netsearch] Menu
・The PowerAct Pro agent on a network and a list of a SNMP/Web card are displayed.
The detail description of a screen
1. Master / Slave Group
Master:The computer name which has installed SC20G22 or the
master agent of PowerActPro is displayed.
Slave:The computer name which has installed the slave agent of
PowerActPro is displayed.
2. Model
UPS model is displayed.
3. UPS Status
The state of UPS is displayed.
4. BatteryStatus
The state of a battery is displayed.
5. CommunicationStatus
A communication state is displayed.
11

1.3. [UPS Management] Menu
・The controllable parameter information on an uninterruptible power supply (UPS) that
the SNMP/Web card was inserted is displayed and set up.
・The user can browse all those sub menus by read-only.
・Read-write access is granted only to the system administrator.
[UPS Configuration] Menu
・Display and set the main operation of uninterruptible power supply (UPS).
Before login
After login
12

The detail description of a screen
1. InputVoltage
It is rated input voltage.
2. InputFrequency
It is rated input frequency.
3. OutputVoltage
It is rated output voltage.
4. OutputFrequency
It is rated output frequency.
5. Output VA
It is maximum output capacity (VA display).
6. Over TemperatureSetPoint
It is a maximum of the operative temperature of an
uninterruptible power supply (UPS). When the temperature of
an uninterruptible power supply (UPS) exceeds this value, a
SNMP/Web card operates an uninterruptible power supply
(UPS) according to a setup of an uninterruptible power supply
(UPS) shutdown menu.
7. Over Load Set Point
It is a maximum of the load of an uninterruptible power supply
(UPS). When the connection capacity of an uninterruptible
power supply (UPS) exceeds this value, a SNMP/Web card
operates an uninterruptible power supply (UPS) according to
a setup of an uninterruptible power supply (UPS) shutdown
menu.
8. Voltage DetectLevel (Only line interactive type)
The voltage sensitivity of an uninterruptible power supply
(UPS) is set up by normal sensitivity or low sensitivity.
9. OutputMode ( Only line interactive type )
The output voltage of an uninterruptible power supply (UPS)
is set up by 115V or 100V.
10. Buzzer
It is a setup of the buzzer operation of uninterruptible
power supply (UPS).
11. All Buzzer Function
The enable/disable of all the buzzer functions is set up
(There
is also a model that cannot be set by the UPS)
13

[UPS Control] Menu
・The immediate stop and reboot of an uninterruptible power supply (UPS) can be
performed.
・Some items can browsed by the access authority holder which can be read and written.
Before login
After login
14

The detail description of a screen
1. ShutdownImmediately
Immediate halt of an uninterruptible power supply (UPS) is
performed.
After clicking execute, UPS will stop after [UPS
shutdown delay time] that appears at the bottom.
The client
shuts down immediately.
2. Restart UPS
An uninterruptible power supply (UPS) is rebooted.
After
clicking execute, UPS will stop after [UPS shutdown delay
time] that appears at the bottom.
In addition, UPS will start after
a lapse of [UPS restart delay time]. The client shuts down
immediately.
The client shuts down immediately.
3. DelayTime for UPS Reboot
Time to hold the Off state at the time of reboot is set up.
4. UPS Shutdown DelayTime
The delay time to an uninterruptible power supply (UPS) stop is
set up after clicking execute. It becomes a common setting of
[UPS management] - [shutdown setting] screen.
5. Turn On UPS/Cancel UPS Shutdown
The halt condition of an uninterruptible power supply (UPS) is
canceled and started. When power supply Off is manually
carried out from the front panel of an uninterruptible power
supply (UPS), it cannot start by this setup.
6. BuzzerTest
A buzzer is immediately sounded for about 1 second.
7. Outlet B/C(control)
The output of the outlet B and C of an uninterruptible power
supply (UPS) is controlled.
8. UPS cold start function
Set whether to enable the cold start function of uninterruptible
power supply (UPS)
9. Maximum Backup Time for AC Fail
Backup time of the UPS is set when an abnormality occurs in
the power input of the uninterruptible power supply (UPS)
15

[UPS Test] Menu
・A battery test and a function test are set up.
・A short-time (about 10 seconds) simple battery test is included in a function test.
・Some items can browsed by the access authority holder which can be read and written.
Before login
After login
16

The detail description of a screen
[BatteryAutoTest]
1. BatteryAutoTest
Enable/disable of the automatic battery test of once every four
weeks is set. Battery test is not done if it is disabled.
2. LastTest Start Time
It is the implementation date and time of the last battery test.
3. LastTestResult
It is the last battery test result.
[Self Test]
1. Self Test
The enable/disable of a test is set up.
2. LastTest Start Time
It is the implementation date of the previous test.
3. LastTestResult
It is the last battery test result.
[BackupTimeTest]
(Only line interactive type)
1. BackupTimeTest
The enable/disable of a test is set up.
2. LastTest Start Time
It is the implementation date of the previous test.
3. LastTestResult
It is the last battery test result.
17

[UPS Test Schedule] Menu
・The schedule for a test is displayed and set up.
Before login
After login
18