Oriental motor EAS Series User manual

Thank you for purchasing an Oriental Motor product.
This Manual describes product handling procedures and safety precautions.
•Please read it thoroughly to ensure safe operation.
•Always keep the manual where it is readily available.
HL-17168-10
Motorized Linear Slide
EAS Series Actuator
OPERATING MANUAL
1 Introduction .............................. 2
2 Safety precautions ................... 4
3 Precautions for use................... 7
4 Preparation.............................. 10
5 Installation............................... 15
6 Connection .............................. 24
7 Maintenance............................ 27
8 Standards, general
specications........................... 35

Introduction
2
1 Introduction
1-1 Before use
Only qualied personnel of electrical and mechanical engineering should work with the product.
Use the product correctly after thoroughly reading the "2 Safety precautions" on p.4. In addition, be sure to
observe the contents described in warning, caution, and note in this manual.
The product described in this manual has been designed and manufactured to be incorporated in general industrial
equipment. Do not use for any other purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused
through failure to observe this warning.
1-2 How to use operating manuals
Operating manuals for the EAS Series are listed below. Operating manuals supplied with the product vary depending
on the type of the product. After reading the manuals, keep them in a convenient place where they are readily
available.
EAS Series equipped with the AZ Series
•EAS Series OPERATING MANUAL Actuator
(this document)
This manual explains the functions as well as the installation method
and others for the motorized linear slide.
•AZ Series OPERATING MANUAL Driver
(supplied with driver) This manual explains items from preparation to basic operations, etc.
•AZ Series Function Edition * This manual explains more detailed operations, functions, etc. that are
not described in OPERATING MANUAL supplied with the product.
•Motorized actuator Function Setting
Edition *
This manual explains settings of parameters required for when a
motorized linear slide is combined with a driver.
•Recovery Guide (supplied with motorized
linear slide)
This manual explains how to create the recovery data le that has
stored the factory setting of the motorized linear slide.
•APPENDIX UL Standards for AZ Series
(Supplied with products conform to the
UL Standards)
This appendix describes the information of the equipped motor
required for recognition of UL Standards.
* This manual does not come with the product. For details, contact your nearest Oriental Motor sales oce or
download from Oriental Motor Website Download Page.
EAS Series equipped with the AR Series
•EAS Series OPERATING MANUAL Actuator
(this document)
•AR Series OPERATING MANUAL Driver
(supplied with driver)
These manuals explain the functions as well as the installation
method and others.
•AR Series USER MANUAL *
This manual explains the equipped motor and driver functions, the
installation and connection method, the data setting method, the
operating method, as well as the troubleshooting and others.
•Motorized actuator Function Setting
Edition *
This manual explains settings of parameters required for when a
motorized linear slide is combined with a driver.
•APPENDIX UL Standards for AR Series
(Supplied with products conform to the
UL Standards)
This appendix describes the information of the equipped motor
required for recognition of UL Standards.
* This manual does not come with the product. For details, contact your nearest Oriental Motor sales oce or
download from Oriental Motor Website Download Page.

Introduction
3
1-3 Equipped motor list
These are the lists of the motor model names that are equipped in the EAS Series.
The power supply current capacity, accessories and others of the drivers to be combined with the motorized linear
slide are described in the OPERATING MANUAL Driver.
Since the motor model names are described in the OPERATING MANUAL Driver, check by reference to those described
in the tables.
EAS Series equipped with the AZ Series
zAC power input type zDC power input type
Motorized linear slide model name Motor model name Motorized linear slide model name Motor model name
EASM4AZAC AZM46AC EASM2AZAK AZM24AK
EASM4AZMC AZM46MC EASM4AZAK AZM46AK
EASM6AZAC AZM66AC EASM4AZMK AZM46MK
EASM6AZMC AZM66MC EASM6AZAK AZM66AK
EASM6AZMK AZM66MK
EAS Series equipped with the AR Series
zAC power input type zDC power input type
Motorized linear slide model name Motor model name Motorized linear slide model name Motor model name
EASM4ARAC ARM46AC EASM2ARAK ARM24SAK
EASM4ARMC ARM46MC EASM2ARMK ARM24SMK
EASM6ARAC ARM66AC EASM4ARAK ARM46SAK
EASM6ARMC ARM66MC EASM4ARMK ARM46SMK
EASM6ARAK ARM66SAK
EASM6ARMK ARM66SMK

Safety precautions
4
2 Safety precautions
The precautions described below are intended to prevent danger or injury to the user and other personnel through
safe, correct use of the product. Use the product only after carefully reading and fully understanding these
instructions.
You must not operate the motorized linear slide (operate the equipment for the specied purpose) if the machine in
which the motorized linear slide is installed does not satisfy the related safety standards.
The factory safety manager or safety personnel in charge of the applicable machine must ensure that the machine is
operated only by qualied personnel who are familiar with the operation of electronic equipment, and thereby
prevent injury or damage to the equipment.
The term“qualied personnel”refers to persons who have received the necessary training or education and have
pertinent experience; who are familiar with the relevant standards, regulations, accident-prevention rules and
inspection conditions; who are authorized by the factory safety manager to engage in the necessary activities; and
who have the ability to discern and prevent potential dangers.
Description of signs
Handling the product without observing the instructions that accompany a "Warning"
symbol may result in serious injury or death.
Handling the product without observing the instructions that accompany a“Caution”symbol
may result in bodily injury or property damage.
The items under this heading contain important handling instructions that the user should
observe to ensure the safe use of the product.
Description of graphic symbols
Indicates "prohibited" actions that must not be performed.
Indicates "compulsory" actions that must be performed.
•Do not use the motorized linear slide in an atmosphere containing explosive, ammable or corrosive
gases, in a place exposed to water, or near ammable objects.
Doing so may result in re, electric shock or injury.
•Do not transport, install, connect, or inspect the motorized linear slide while the power is supplied.
Doing so may result in electric shock.
•Do not forcibly bend, pull, or pinch the cable.
Doing so may result in re or electric shock.
•Do not disassemble or modify the motorized linear slide.
Doing so may result in injury or damage to equipment.
•Never use a motorized linear slide in a medical device used in connection with the maintenance or
management of human life or health, or in a transportation system whose purpose is to move or carry
people.
•Do not use the brake mechanism of the electromagnetic brake motor as a deceleration/safety brake.
Doing so may result in injury or damage to equipment.
•Do not collide the table with the mechanical stopper in operations other than push-motion return-to-
home operation or push-motion operation.
Doing so may result in injury or damage to equipment.

Safety precautions
5
•Assign qualied personnel the task of installing, wiring, operating/controlling, inspecting and
troubleshooting the motorized linear slide.
Failure to do so may result in re, electric shock, injury or damage to equipment.
•Take measures to keep the moving parts in position for vertical operations such as elevator
applications.
Failure to do so may result in injury or damage to equipment.
•Operate the data setter outside the safety cage.
Failure to do so may result in injury.
•Be sure to provide a safety cage conforming to EN ISO 13857 to prevent persons from entering the
moving range of the motorized linear slide while power is supplied to the motorized linear slide. Turn
o the main power to the driver before performing adjustment or inspection in which the table is
moved manually.
Accidental contact may result in serious injury.
•When the driver generates an alarm (any of the driver’s protective functions is triggered), take
measures to hold the moving part in place since the motor stops and loses its holding torque.
Failure to do so may result in injury or damage to equipment.
•Install the motorized linear slide in an enclosure.
Failure to do so may result in electric shock or injury.
•The motorized linear slide is Class I equipment, and therefore install so as to prevent from directly
touching the motorized linear slide, or make sure to ground it.
Failure to do so may result in electric shock.
•Provide an emergency stop device or emergency stop circuit external to the equipment so that the
entire equipment will operate safely in the event of a system failure or malfunction.
Failure to do so may result in injury.
•Perform the return-to-home operation after the power is restored. When the absolute-position backup
system is used, positioning operation of the absolute mode is executed.
Failure to do so may result in injury or damage to equipment.
•Operate the motorized linear slide after setting the resolution, moving direction or other parameters.
If the motorized linear slide is operated without setting parameters, the table may move to
unexpected directions or run at unexpected speeds, causing injury or damage to equipment.
(A variety of parameters have been set to the motorized linear slide equipped with the AZ Series at
the time of shipment.)
•When the motor of the motorized linear slide equipped with the AZ Series is replaced, be sure to
create the recovery data le in accordance with the AZ Series Function Edition before starting
operation of the equipment.
If the replacement is not performed in accordance with the procedures, the table may move to
unexpected directions or run at unexpected speeds, leading to injury or damage to equipment.
•After replacing the driver, set the resolution, moving direction or other parameters before operating
the motorized linear slide.
If the motorized linear slide is operated without setting parameters, the table may move to
unexpected directions or run at unexpected speeds, causing injury or damage to equipment.

Safety precautions
6
•Do not use the motorized linear slide beyond its specications.
Doing so may result in electric shock, injury or damage to equipment.
•Keep your ngers and objects out of the openings in the motorized linear slide.
Failure to do so may result in re, electric shock or injury.
•Do not touch the motorized linear slide while operating or immediately after stopping.
Doing so may result in a skin burn(s).
•Do not carry the motorized linear slide by holding its cables or its moving part.
Doing so may cause injury.
•Keep the area around the motorized linear slide free of combustible materials.
Failure to do so may result in re or a skin burn(s).
•Do not leave anything around the motorized linear slide that would obstruct ventilation.
Doing so may result in damage to equipment.
•Do not touch the moving part during operation.
Doing so may result in injury.
•Do not touch the terminals while conducting the insulation resistance measurement or the dielectric
strength test.
Accidental contact may result in electric shock.
•Do not use the sensor set (accessory) as safety components.
Doing so may result in injury or damage to equipment.
•Use a motorized linear slide and driver only in the specied combination.
An incorrect combination may cause a re.
•The motorized linear slide is very heavy. When transporting or installing the motorized linear slide,
make sure two persons work together to carry out the necessary tasks.
Failure to do so may result in injury.
•Wear a helmet, safety shoes, gloves or other protective gear when transporting or installing the
motorized linear slide.
Failure to do so may result in injury.
•When replacing a motor, use the motor whose model number is the same as the one mounted at the
time of shipment.
If a motor being dierent from the one at the time of shipment is mounted, the specications cannot
be satised, and, in addition, damage to the equipment or injury may result.
•The motor surface temperature may exceed 70 °C (158 °F) even under normal
operating conditions. If the operator is allowed to approach the running motor,
attach a warning label as shown below in a conspicuous position.
Failure to do so may result in a skin burn(s) Warning label

Precautions for use
7
3 Precautions for use
This chapter covers limitations and requirements the user should consider when using the product.
General
zAlways use the supplied cable or accessory cable to connect the motorized linear slide and driver.
In the following condition, an appropriate accessory cable must be purchased separately.
•If a exible cable is to be used.
•If a cable of 3 m (9.8 ft.) or longer is to be used.
•If a motorized linear slide and driver package without a cable was purchased.
zWhen conducting the insulation resistance measurement and the dielectric strength test, be sure to
separate the connection between the motor and the driver.
Conducting the insulation resistance measurement or dielectric strength test with the motor and driver connected
may result in damage to equipment.
zDo not make an impact on the motorized linear slide.
Do not drop the motorized linear slide. Also, do not hit the motorized linear slide on something hard. Doing so may
cause the positioning accuracy decrease, the motor damage or the product service life reduction.
zMake sure not to hit or apply a strong impact on the encoder (ABZO sensor).
•Making a strong impact on an encoder (ABZO sensor) may cause the motor malfunction or damage to the encoder
(ABZO sensor). When transporting the motorized linear slide or installing a load, handle the motorized linear slide
carefully not to make a strong impact on the moving part.
•The warning label shown in the right is indicated on the motor of the motorized
linear slide equipped with the AZ Series.
Warning label
zDo not move the encoder (ABZO sensor) toward a strong magnetic eld.
A magnetic sensor is built into the encoder (ABZO sensor). If the motor is installed close to equipment which
generates a strong magnetic eld, the encoder (ABZO sensor) may break or malfunction. Especially, the EAS2 type
equipped with the AZ Series is easily aected by a magnetic eld, so make sure the environment at transportation
and storage as well as the installation location in use.
Keep the magnetic ux density on the surface of the encoder (ABZO sensor) so as not to exceed the values in the
table.
Model Magnetic ux density
When transporting and storing When operating
EAS2 5 mT 2 mT *
EAS4
EAS6 10 mT 10 mT
* When the magnetic ux density is exceeding 1 mT and 2 mT or less, use in an environment where the operating
ambient temperature is exceeding 20 °C (68 °F) and 40 °C (104 °F) or less.
zMeshing noise of mechanical sensor
A gear type mechanical sensor is built into the encoder (ABZO sensor). Although the meshing noise of gears may
generate, it is not malfunction.
zThe EAS2 type equipped the AZ Series does not have the models with an electromagnetic brake.
Take measures to keep the moving part in position for vertical operations such as elevator applications.

Precautions for use
8
Temperature
zUse the motorized linear slide equipped with the AZ Series in conditions where the motor surface
temperature will not exceed 80 °C (176 °F).
The motor surface temperature may exceed 80 °C (176 °F) under certain conditions (ambient temperature, operating
speed, duty cycle, etc.). In order to protect the encoder (ABZO sensor), use the motor in conditions where the surface
temperature does not exceed 80 °C (176 °F). If the encoder (ABZO sensor) temperature reaches the upper limit, the
motor overheat alarm will generate.
zUse the motorized linear slide equipped with the AR Series in conditions where the motor surface
temperature will not exceed 100 °C (212 °F).
The motor does not have a function to protect from overheating. The motor surface temperature may exceed 100 °C
(212 °F) under certain conditions (ambient temperature, operating speed, duty cycle, etc.). To prevent the motor
bearings (ball bearings) from reaching its usable life quickly, use the motor in conditions where the surface
temperature does not exceed 100 °C (212 °F).
Operation
zIn the case of the DC power input type products, the maximum speed may not be reached depending
on the ambient temperature or the length of the motor cable.
zHolding torque at standstill
When the motorized linear slide stops, the holding torque will be reduced by the current cutback function of the
driver. When selecting the motorized linear slide, check the holding torque at standstill in the specications on the
catalog.
zDo not use the electromagnetic brake to reduce speed or as a safety brake.
Do not use the electromagnetic brake as means to decelerate and stop the motorized linear slide. The brake hub of
the electromagnetic brake will wear signicantly and the braking force will drop. Since the power o activated type
electromagnetic brake is equipped, it helps maintain the position of the load when the power is cut o, but this brake
cannot securely hold the load in place. Accordingly, do not use the electromagnetic brake as a safety brake. To use the
electromagnetic brake to hold the load in place, do so after the motorized linear slide has stopped.
Notes for when the connection cable is used
Note the following points when a supplied cable or an accessory cable is used.
zWhen inserting the connector
Hold the connector main body, and insert it in straight securely.
Inserting the connector in an inclined state may result in damage
to terminals or a connection failure.
zWhen pulling out the connector
Pull out the connector in straight while releasing the lock part of
the connector. Pulling out the connector with holding the cable
(lead wire) may result in damage to the connector.
zBending radius of cable
Use the cable in a state where the bending radius of the cable is
more than 6 times of the cable diameter.
In the case of the lead wire type, use in a state where the bending
radius is more than 4 times of the diameter of the lead wires.
Mo
re than 6 times of cable diameter

Precautions for use
9
zHow to x the cable
Fix the cable at the positions near the connector so as to apply no stress on the connector part.
Take measures so as to apply no stress on the connector by using wide clamps or by xing at two places.
In the case of the EAS2 type equipped with the AZ Series, x both end of the cable covering part. Do not x the lead
wires.
In the case of a exible cable,
this area is a movable range.
Fix
Fix
In the case of a exible cable,
this area is a movable range.
Fix
Fix
Motorized linear slide
 EAS2
 EAS4, EAS6
Driver
Driver

Preparation
10
4 Preparation
This chapter explains the items you should check, as well as the name of each part.
4-1 Checking the product
Verify that the items listed below are included. Report any missing or damaged items to the Oriental Motor sales
oce from which you purchased the product.
When purchasing a motorized linear slide and driver package When purchasing a motorized linear slide only
•Motorized linear slide
•Driver
•OPERATING MANUAL Actuator (this document)
•OPERATING MANUAL Driver
•Recovery Guide
(Supplied with the models equipped with the AZ Series)
•APPENDIX UL Standards *1
•Connectors bag
•Cable for motor *2
•Cable for electromagnetic brake *2
(Supplied with electromagnetic brake types)
•Cable for encoder *2
(Supplied with the models equipped with the AZ Series)
•Varistor *3
(Supplied with the models equipped with the AR Series)
•Motorized linear slide
•OPERATING MANUAL Actuator (this document)
•Recovery Guide
(Supplied with the models equipped with the AZ
Series)
•APPENDIX UL Standards *1
•Varistor *3
(Supplied with the models equipped with the AR
Series)
*1 Supplied with products conform to the UL Standards.
*2 When the product is supplied with a connection cable.
*3 Supplied with the motorized linear slides equipped with the DC power input type motor with electromagnetic
brake which are combined with the pulse input type driver.

Preparation
11
4-2 How to identify the product model
Verify the model number of the purchased product against the number shown on the package label.
Check the model number of the motorized linear slide against the number shown on the nameplate.
Motorized linear slide and driver package model
zEAS2
E A S 2 N X - F 0 0 5 - A Z A K D - 3
1 2 4 5 6 7 8 9 10 11 12
zEAS4, EAS6
E A S 4 R N X - D 0 2 5 - A Z M K D - 3
1 2 3 4 5 6 7 8 9 10 11 12
1 Series name EAS : EAS series
2 Linear slide size *
2 : Width 40 mm, Height 38 mm (Width 30 mm, Height 38 mm)
4 : Width 58.4 mm, Height 60 mm (Width 45 mm, Height 60 mm)
6 : Width 75.4 mm, Height 83 mm (Width 62 mm, Height 83 mm)
3Motor mounting
direction
R: Parallel motor mounting type (Right side)
L: Parallel motor mounting type (Left side)
Blank : In-line motor mounting type
4Sensor mounting
rail
N: Without sensor mounting rail
Blank : With sensor mounting rail
5 Table X : X-table
Y : Y-table
6 Ball screw lead
D: 12 mm
E: 6 mm
F: 3 mm
7 Stroke 005 to 085 : 50 to 850 mm (50 mm unit)
8 Motor AZ : AZ Series
AR : AR Series
9 Motor type A: Single shaft
M: With electromagnetic brake
10 Power supply input
•Motorized linear slide equipped with the AZ Series
A: Single-phase 100-120 VAC
C: Single-phase/Three-phase 200-240 VAC
K: 24/48 VDC (EAS2 type is 24VDC)
•Motorized linear slide equipped with the AR Series
A: Single-phase 100-120 VAC (Single-phase 100-115 VAC for the pulse input type)
C: Single-phase 200-240 VAC (Single-phase 200-230 VAC for the pulse input type)
S: Three-phase 200-230 VAC (For the pulse input type only)
K: 24/48 VDC (EAS2 type is 24VDC)
11 Driver type D: Built-in controller type
Blank : Pulse input type
12 Connection cable Number : Length of supplied cable (m)
Blank : Without connection cable
* The values in ( ) are width of without sensor mounting rail type.

Preparation
12
Motorized linear slide model
zEASM2
E A S M 2 N X F 0 0 5 A Z A K
1 2 4 5 6 7 8 9 10
zEASM4, EASM6
E A S M 4 R N X D 0 2 5 A Z M K
1 2 3 4 5 6 7 8 9 10
1 Series name EASM : EAS series
2 Linear slide size *
2: Width 40 mm, Height 38 mm (Width 30 mm, Height 38 mm)
4: Width 58.4 mm, Height 60 mm (Width 45 mm, Height 60 mm)
6: Width 75.4 mm, Height 83 mm (Width 62 mm, Height 83 mm)
3 Motor mounting direction
R: Parallel motor mounting type (Right side)
L: Parallel motor mounting type (Left side)
Blank : In-line motor mounting type
4 Sensor mounting rail N: Without sensor mounting rail
Blank : With sensor mounting rail
5 Table X: X-table
Y: Y-table
6 Ball screw lead
D: 12 mm
E: 6 mm
F: 3 mm
7 Stroke 005 to 085 : 50 to 850 mm (50 mm unit)
8 Motor AZ : AZ Series
AR : AR Series
9 Motor type A: Single shaft
M: With electromagnetic brake
10 Motor power supply type C: AC power supply input
K: DC power supply input
* The values in ( ) are width of without sensor mounting rail type.

Preparation
13
4-3 Names of parts
Motor
Table
Top cover
Sensor mounting rail
Coupling case
Motor
Table
Top cove
r
Pulley cover
Sensor mounting rail
In-line motor mounting type Parallel motor mounting type
Mechanism of the parallel motor mounting type
Motor mounting screws
Motor mounting screws
Tension adjustmen
t
springs *2
P
ulley cover
Pulley
Belt
Tension adjustment
screws *1
*1 The motor is xed in the position where the belt tension becomes optimum.
*2 Springs for belt tension adjustment are installed.
Motor
zMotorized linear slide equipped with the AZ Series
Electromagnetic brake cable
Electromagnetic
brake
Motor cable
Encoder cable
Protective Earth Terminal
Encoder
(ABZO sensor)
Encoder
(ABZO sensor)
Motor/encoder connector
Motor
The f
ollowing gure show models for the electromagnetic brake
type and
AC power input.
The following gure show models for the
standard type and DC power input.
Motor
EAS4, EAS6 EAS2

Preparation
14
zMotorized linear slide equipped with the AR Series
The following gure show models for the electromagnetic brake type and AC power input.
Elec
tromagnetic brake cable
Motor cable
Motor
Connector cover
Protective Earth Terminal
Electromagnetic brake

Installation
15
5 Installation
5-1 Location for installation
The motorized linear slide has been designed and manufactured to be incorporated in general industrial equipment.
Install them in a well-ventilated location that provides easy access for inspection. The location must also satisfy the
following conditions:
•Inside an enclosure that is installed indoors (provide vent holes)
•Operating ambient temperature: 0 to +40 °C [+32 to 104 °F] (non-freezing)
•Operating ambient humidity: 85% or less (non-condensing)
•Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid
•Area not exposed to direct sun
•Area free of excessive amount of dust, iron particles or the like
•Area not subject to splashing water (rain, water droplets), oil (oil droplets) or other liquids
•Area free of excessive salt
•Area not subject to continuous vibration or excessive shocks
•Area free of excessive electromagnetic noise (from welders, power machinery, etc.)
•Area free of radioactive materials, magnetic elds or vacuum
•Up to 1000 m (3,300 ft.) above sea level
If a motor is installed in an environment where a magnetic eld is generated
A magnetic sensor is built into the encoder (ABZO sensor). If the motor is installed close to equipment which
generates a strong magnetic eld, the encoder (ABZO sensor) may break or malfunction.
Keep the magnetic ux density on the surface of the encoder (ABZO sensor) so as not to exceed the values in the
table.
Model Magnetic ux density
EAS2 2 mT *
EAS4
EAS6 10 mT
* When the magnetic ux density is exceeding 1 mT and 2 mT or less, use in an environment where the operating
ambient temperature is exceeding 20 °C (68 °F) and 40 °C (104 °F) or less.
Do not install the motor close to equipment which generates a strong magnetic eld.

Installation
16
5-2 Installing the motorized linear slide
The motorized linear slide can be installed in any direction.
Taking account of vibration prevention as well as deection of the motorized linear slide, install it on a metal surface
of sucient strength (thickness 10 mm or more). Secure so that the entire area of the bottom face of the motorized
linear slide contacts the mounting plate.
Install the motorized linear slide so that the cable or encoder does not contact the mounting plate.
Mounting plate
Mounting screw
s
Positioning pins
Mounting plate
The thickness of the mounting plate described in the table is the minimum requirements for installation. If the
accuracy is required, design the thickness of the mounting plate in consideration of the installation conditions such as
load condition, rigidity, vibration and others.
Model Material Thickness Flatness against the mounting
reference surface
EAS2
Aluminum 10 mm or more
0.05 mm or less
EAS4 0.06 mm or less
EAS6 0.07 mm or less
Positioning pin
Model Pin diameter Length from the
mounting plate
EAS2 ø4
0
- 0.012
mm 4 mm or less
EAS4
EAS6 ø6
0
- 0.012
mm 5 mm or less

Installation
17
Mounting screw
Model Screw size Tightening torque Length from the
mounting plate
EAS2 M4 2.4 N·m (340 oz-in) 4 mm or less
EAS4 M5 5 N·m (710 oz-in) 6 mm or less
EAS6 M6 5 N·m (710 oz-in) 8 mm or less
About the length of mounting screws and positioning pins from the mounting plate, be sure to
observe the specied value. Exceeding the specied value may cause the table to break, leading to
injury or mechanical damage.
Mounting screwPositioning pin
Specied value or less
Specied value or less
When the EAS2 type equipped with the AZ Series is installed in equipment
The encoder (ABZO sensor) of the EAS2 type equipped with the AZ Series is easily aected by a magnetic eld, so
make sure the installation location. When motors are installed side by side, ensure distances in horizontal and vertical
directions of more than the frame size of the other motor installed.
A mm
(A in.)
A mm
(A in.)
A mm
(A in.)
Motor frame size
A mm (A in.) *
A mm (A in.)A mm (A in.)
A mm (A in.)A mm (A in.)
* Ensure distances of more than the frame size [A mm (A in.)] of the other motor.
zReference
Other motor A
Motor frame size 20 mm (0.79 in.) 20 mm (0.79 in.)
Motor frame size 28 mm (1.10 in.) 28 mm (1.10 in.)
Motor frame size 42 mm (1.65 in.) 42 mm (1.65 in.)
Motor frame size 60 mm (2.36 in.) 60 mm (2.36 in.)

Installation
18
Release the electromagnetic brake
When moving the table of the electromagnetic brake type manually, connect the 24 VDC power supply for
electromagnetic brake to release the electromagnetic brake.
zSpecications of a power supply for electromagnetic brake
Model Voltage Current capacity
EAS2
24 VDC±5% *
0.05 A or more
EAS4 0.08 A or more
EAS6 0.25 A or more
* If the distance between the motorized linear slide with an electromagnetic brake and the driver is extended to the
following length, use a power supply of 24±4% VDC.
Motorized linear slide equipped with the AZ Series : 20 m (65.6 ft.)
Motorized linear slide equipped with the AR Series : 20 to 30 m (65.6 to 98.4 ft.)
zReleasing procedure
1. Connect the“electromagnetic brake cable”and“cable for electromagnetic brake.”
2. Connect the lead wires of the“cable for electromagnetic brake”to the 24 VDC power supply.
Connect the white lead wire to the +24 VDC terminal, and the black lead wire to the GND terminal.
3. Turn on the 24 VDC power supply.
The electromagnetic brake will be released and the table will be able to move by hand.
Cable for electromagnetic brake
Electromagnetic brake cable 24 VDC
power supply
Switch
White
Black Varistor *
* Be sure to connect the varistor to protect the contact of the switch or to prevent electrical noise.
Motorized linear slide equipped with the AZ Series : Recommended varistor: Z15D121 (SEMITEC Corporation)
Motorized linear slide equipped with the AR Series : Use the supplied varistor.
The lead wires of the“cable for electromagnetic brake”have polarities, so connect them in the correct
polarities. If the lead wires are connected with their polarities reversed, the electromagnetic brake
will not operate properly.

Installation
19
5-3 Changing the motor cable leading direction
The motor cable leading direction can be changed according to the space of equipment.
•When changing the motor cable leading direction, remove the load, and perform in a state
where the motorized linear slide is placed in a horizontal position. Doing the operation in a
vertical condition may allow the moving part to fall, leading to injury or mechanical
damage.
· If the motor mounting screws are removed in a state where the motorized linear slide is
installed vertically, the motor may rotate rapidly. Thereby, ngers may be caught in the
product or the cable may be disconnected.
•Set the home position again after mounting a motor. If the motorized linear slide is
operated without setting the home position again, the moving part may move to
unexpected directions or run at unexpected speeds, leading to injury or mechanical
damage.
· The moving part of the motorized linear slide may collide with the mechanical stopper.
· The load may collide with other equipment.
•Be sure to secure the coupling with the specied tightening torque. Unless it is secured
with the specied torque, the ball screw may rotate idly, leading to injury or mechanical
damage.
 When the motorized linear slide is used in a vertical condition, the load may fall.
 When the motorized linear slide is used in a horizontal condition, the moving part of the
motorized linear slide may collide with the mechanical stopper. Also, the load may collide
with other equipment.
In-line motor mounting type
1. Remove the cap, and loosen the coupling xing screw.
Coupling xing
screw (M1.6)
Coupling
Cap Cap
Three turns
or less
Coupling xing
screw (M2.5)
Three turns
or less
EAS6
Coupling xing
screw (M1.6)
Coupling
Cap
Three turns
or less
EAS2 EAS4
•When loosing the coupling xing screw, do not insert the tool diagonally.
•Do not use the ball-end hex key.
•To prevent the coupling xing screw from falling o, keep three turns or less when turning the
screw.

Installation
20
2. Remove the motor mounting screws, and dismount the motor.
Motor mounting screws
(M3, 4 places)
Motor mounting
screws (M2.5, 2 places)
Motor mounting screws
(M4, 4 places)
EAS6EAS4EAS2
3. Change the cable leading direction, and mount the motor.
Mount the motor according to the procedure opposite of dismounting it.
Refer to the table below for the tightening torque of the coupling xing screw and motor mounting screw.
Model Coupling xing screw Motor mounting screws
Nominal size Tightening torque Nominal size Tightening torque
EAS2 M1.6 0.25 N·m (35 oz-in) M2.5 0.5 N·m (71 oz-in)
EAS4 M1.6 0.25 N·m (35 oz-in) M3 1 N·m (142 oz-in)
EAS6 M2.5 1 N·m (142 oz-in) M4 2.4 N·m (340 oz-in)
Use a tool capable of controlling the torque when tightening the coupling xing screw.
4. After mounting the motor, set the home position again.
Parallel motor mounting type
The cable leading direction can be changed to one of three directions.
1. Remove the pulley cover xing screws, and detach the pulley cover.
Pulley cover xing screws (M3)
Pulley cover
Pulley cover xing screws (M3)
Pulley cover
EAS6EAS4