Orlaco CornerEye LHD User manual

www.orlaco.com
Orlaco is a Manufacturing company that specializes in making cameras
and monitor systems for commercial vehicles, fork-lift trucks, cranes, off
shore and maritime.
Our objective is to design and produce camera systems for the profes-
sional market that improve the drivers view and increase operating
efficiency.
At our factory in Barneveld, we have a production department, ware-
house, design department, service department and showroom.
Vision is our mission®, and Orlaco therefore deploys the development,
manufacture, supply and service of camera and display systems that will
improve safety and efficiency of all vehicles, machinery and vessels. Our
systems give the end user a view on each blind spot and create comfort
and improved working conditions. Our active approach will support mar-
ket demands and innovations and will lead to enthusiastic ambassadors
in the market; our Customers.
For more information: www.orlaco.com
MAN Drilling template
CornerEye®
LHD
Manual for drilling pattern
No. IM0973604, A 02
05/2017
English

2
Safety
In order to guarantee safe operation, these safety
instructions must be read before you start using this
equipment.
• Do not open the enclosure. This can cause damage,
short-circuiting or electrical shocks.
• Do not expose the equipment to extreme temperatures.
This can cause deformation of the enclosure or damage
to internal components.
• Repairs may only be undertaken by the manufacturer.
• The equipment must be installed as shown in this
manual.
Preface
Before you start using this equipment, please read this manual
carefully and follow all instructions. If you have any questions or issues
concerning the operation of this equipment, consult the relevant section
in the manual or contact the Service department.
All data subject to change without notice. All dimensions are for commer-
cial purpose only. The camera/display systems comply with the latest CE,
ADR, EMC and mirror-directive regulations. All products are manufac-
tured in accordance with the ISO 9001 quality management system, ISO/
TS16949 quality automotive and ISO 14001 environmental management
systems.
Contents
Page
1. Introduction 3
2. MAN TGS, TGX Corner shields 3
2.1. Step1 3
2.2. Step2 4
3. Additional work for cabling. 6
4. Maintenance and cleaning 7
5. Disposal 7
6. General terms and conditions 7
7. Release notes 7
Available documentation
IM0973520 Set Camera HMOS CornerEye®
DS0963141-0402620 Bracket HMOS CornerEye®
Side view
Top view
40
60
30 30
7mm 7mm
Hole for Camera cable
Hole Pattern MAN TGS and TGX
Hole for Bolt M6 Hole for Bolt M6
23mm
2
Bolts 2x M6 x 35
The grommet is inserted
as a spare part in the bracket,
remove for any application
Extension
Please use the included drilling pattern on pages 4 to 5
Manual drilling pattern
IM0973604 A 02
MAN Drilling template CornerEye®
LHD
7
Manual drilling pattern
IM0973604 A 02
4. Maintenance and cleaning
This product can only work correctly by using fluid for glass cleaning
used in the automotive industry with desired temperature of -40°C to
+85°C. Do absolutely not use aggressive chemicals or abrasive cleaning
agents.
5. Disposal
Disassembly, removal and disposal. Local regulations for dealing with
waste must be followed when disposing of disassembled components or
entire units.
6. General terms and conditions
The manufacturer is not liable for damage resulting from inadequate
installation or alterations made to the equipment without informing the
manufacturer in writing.
This installation manual has been made available by the manufacturer.
All rights reserved. No part of this manual may be reproduced and/or
made public in printed form, in photocopy form or digital, or in any other
way, without the prior written permission of the manufacturer. This also
applies to the associated drawings and figures.
The manufacturer reserves the right to make changes to components at
any time without informing customers beforehand or directly.
All dimensions given are for commercial purposes.
This manual has been prepared with all due care and attention.
However, the manufacturer cannot be held responsible for any errors in
this manual or any consequences thereof.
7. Release notes
A 01. First edition; May 2017.
A 02. Drawing page 4,5 changed; August 2017.

6
Manual drilling pattern
3. Additional work for cabling.
In order to make room for the cable a piece of the foam behind the corner
shield needs to be removed.
In this way there is enough room for the cable behind the corner shield.
See also the pictures on the right side.
Foam behind the corner shield
A piece of the foam behind the corner shield needs to be removed.
IM0973604 A 02
3
1. introduction
Description to drill the hole pattern for the CornerEye® Camera on the
Corner shields MAN TGS and TGX.
2. MAN TGS, TGX Corner shields
2.1. Step 1
Determine the height position of the 23mm hole.
See page 4 for the next step.
Manual drilling pattern
IM0973604 A 02
Reference point Reference point
TGX Corner shield
TGS Corner shield
23mm hole
23mm hole
155mm
135mm
104mm
107mm
90°
90°
5

4
Manual drilling pattern
2.2. Step 2
Using this template, you can determine the other dimensions on the
corner shields.
NOTE:
To print this page, use the setting “actual size” or
“scale 100%” = A3.
IM0973604 A 02
Position this side to edge of corner shield
Scale 1:1
Units in mm
7mm hole (2x)
23mm hole
155mm to Reference point
2mm
30mm 30mm
TGS Cornershield template
NOTE:
PLEASE VERIFY SCALE
BY CHECKING IF MEASUREMENTS
ARE UP TO SCALE
See step 1
104mm
5
Manual drilling pattern
IM0973604 A 02
Position this side to edge of corner shield
7mm hole (2x)
23mm hole
135mm to Reference point
2mm
30mm 30mm
TGX Cornershield template
See step 1
107mm