Osram LMS134R2 User manual

Wireless Wallstations
Wiring and installation manual
www.osram.us
Light is OSRAM

Overview
Wireless Wallstations with integrated LED indicators are available in a range
of configurations for customized light level control. The wireless wallstations
obtain their operating power from two AA alkaline batteries and feature several
options for functionality depending on the model installed.
The wireless wallstations obtain their address during the commissioning
process and no actions are required during installation.
Important Safeguards
Note
Tip
!
STOP
When using electrical equipment, basic safety precautions should always
be followed including the following:
—READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
—Do not mount near gas or electric heaters.
—Equipment should be mounted in locations and at heights where it will not
readily be subjected to tampering by unauthorized personnel.
—The use of accessory equipment is not recommended by OSRAM as it may
cause an unsafe condition.
—Do not use this equipment for other than the intended use.
Note
Tip
!
STOP
SAVE THESE INSTRUCTIONS
Wireless Works with ENCELIUM®Works with ENCELIUM EDGE™
Wallstation Ordering Code EXTEND Networked LMS Standalone LMS
2-Button EN-WS-2B-ZB-WH X X
3-Scene EN-WS-SC3-ZB-WH X X
5-Scene EN-WS-SC5-ZB-WH X X
3-Zone EN-WS-ZC3-ZB-WH X
6-Zone EN-WS-ZC6-ZB-WH X
2

Battery Installation
Two AA alkaline batteries are provided with each wireless wallstation. When
replacing these batteries, use only alkaline-type batteries. Install the batteries
according to the battery compartment markings.
Dispose of used battery promptly. Keep away from children. Do not disassemble
and do not dispose in fire.
3
Battery slots
Wallstation - Rear view
Mounting bracket J-Box
Electrical Metal Device Box:
Install the mounting bracket using the supplied screws. Ensure that the OSRAM
logo and SINGLE GANG labels are facing up.
Wallstation Installation

Mounting bracket Old Work Low Voltage
Mounting Bracket
Low Voltage Device Box:
Wallstation Installation (continued)
Place the wallstation assembly into the mounting plate and push gently until
‘clicks’ are heard. This confirms that the pieces are secured.
4

Decorator Plate Installation
The wireless wallstation can also be installed with an off-the-shelf decorator-
style wall plate. Multi-gang WS installations require multi-gang decorator wall
plates.
Remove the button assembly from the OSRAM wall plate. This can be achieved
by pressing the wall plate with your thumbs near the button assembly while
grasping the OSRAM Wall Plate.
Install the supplied wall strips to the wireless wallstation until they snap in.
5

Decorator Plate Installation (continued)
Orient the mounting bracket such that the DECORATOR and MULTI GANG
labels are facing up. Insert the wallstation button assembly into the mounting
plate until ‘clicks’ are heard. Clicks confirm that the pieces are secured.
Install the mounting bracket using the supplied screws. Install the decorator
plate using screws supplied with the decorator plate.
6

Installation Notes
Consult the OSRAM website for the most up-to-date version of the wireless
system design guide and install this product according to the guidelines.
The Wireless Wallstation is to be installed in dry, indoor locations ONLY. Do not
install the Wireless Wallstation in damp locations. Damp locations are defined
as: interior locations subject to moderate degrees of moisture, such as base-
ments, barns, cold-storage warehouses, as well as partially protected locations
under canopies, marquees and open roofed porches.
Troubleshooting
There are no user-serviceable parts inside the Wallstation. Please return the
device to OSRAM if service is required.
Regulatory Approvals
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under FCC rules.
This equipment has been tested and found to comply with Industry Canada
ICES-003 Issue 5 (CAN ICES-3 (A)/NMB-3(A)).
Contains FCC ID: H79DFZM-E7220
Contains IC ID: 4259B-DFZM7220
7

© 2018 OSRAM SYLVANIA Inc.
LMS134R2 4-18
OSRAM is a registered trademarks of OSRAM GmbH.
ENCELIUM EXTEND is a registered trademark of OSRAM SYLVANIA Inc.
ENCELIUM EDGE is a trademark of OSRAM SYLVANIA Inc.
Specifications subject to change without notice..
OSRAM SYLVANIA Inc.
200 Ballardvale Street
Wilmington, MA 01887 USA
888-531-7573
www.osram.us/ds