Outsider Holscher PLATEAU SEAT 195 Installation instructions manual

PLATEAU SEAT
#195 #200 MOUNTING GUIDE
Kigkurren 8A Islands Brygge DK2300 Copenhagen · out-sider.dk

02
Seat 900
• 3 pcs M8x100 allen key screw
• 3 pcs M8 nuts
• 3 pcs M8 washer
Seat 1250
• 5 pcs M8x100 allen key screw
• 5 pcs M8 nut
• 5 pcs M8 washer
PLEASE NOTE:
The drawings in this manual show PLATEAU Seat 900 - the small
version. The exact same mounting principles are applied to the 1250
and the 1800 versions.
PLATEAU SEAT
Developed by out-sider in collaboration with Holscher Design 2019.
INDEX: PAGE
Item list ......................................................................................02
Mounting surface bracket .........................................................03
Mounting of seat on surface bracket.......................................04
Fixation of disc ..........................................................................05
Plateau side-table .....................................................................06
Mounting of legs .......................................................................07
Cleaning and maintenance .....................................................08
ITEM LIST ADDONS
Addons, not included with standard product
Seat 1800
• 5 pcs M8x100 allen key screw
• 5 pcs M8 nuts
• 5 pcs M8 washer
Seat 1800
• 1 pcs M8x20 allen key screw
Tools (not included)
• Allen key set
• Socket wrench set
• Screws and bolts for the mounting of the surface bracket
(depends on customer wishes and surface, see p. 04)
1x Point Sun
f. Seat
1x Side table
(#196, #200)

03
1 : MOUNTING OF SURFACE BRACKET
The surface bracket needs to be mounted on a surface before its assembled with Seat. The bracket has four
holes made ready for surface mounting. Use your preferred bolts or screws to mount the bracket.
Seat 1250 and Seat 1800
Make sure the two brackets have the
correct distance (24cm) between them,
before mounting them to the surface.
24 cm
Ø11 mm holes

04
2 : MOUNTING OF SEAT ON SURFACE BRACKET
Use the included M8 x 100mm allen key bolts to ix the sitting surface to the ixated surface
bracket. Tighten the bolts and nuts with allen key no 6. and a 17mm spanner tool.
Seat 1250 and Seat 1800
Use two brackets, same principle.
M8x100 bolt
Nut
Washer
Seat 900
Seat 900

05
3 : FIXATION OF DISC
Use one of the included M8 x 100mm unbraco bolts to ix the disc into place. Allen key nr 6.
Disc for Seats
Nut
Washer
M8x100 bolt

06
MOUNTING OF SIDE-TABLE ON SEAT
Lower Side-table into the circular slot. Rotate Side-table in such a way, that the two holes align with the steel
frame. Reuse the bolts, nut and the washer from your previous disassembly of the disc-tube.
Seat 900, 1250, 1800
Side-table mounted on Seat M8x100 bolt
Nut
Washer
M8x20
PLATEAU SIDE-TABLE
#200

07
MOUNTING OF LEGS
Use M8x100 and M8 nut to fasten the two legs (204 1010). Out-sider does not provide tools and
materials for surface mounting through the top lange, but recommends countersunk M8M10
bolts.
204 1010
M8x100 bolt
M8 nut
Seat 900, 1250, 1800
Legs (204 1010) mounted on Seat

08
CLEANING
Clean the laminate surface with warm water and a soft sponge.
NEVER use the abrasive “green” side of the sponge. Use an ordinary universal cleaner.
Diicult dirt must be removed with a nano sponge and water. Please take a closer
look at our website, or contact us for information.
Kigkurren 8A
Islands Brygge
DK2300 Copenhagen
out-sider.dk
[phone]