Outsider Plateau User guide

24.01.2017
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
MOUNTING
INSTRUCTION
Parts included:
2 pcs M8x20 bolts
20 pcs M6x10 bolts
16 pcs M6x30 bolts
8 pcs M10x60 bolts
8 pcs M10 nut
2 pcs long discs
4 pcs round discs
PLATEAU
#177

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
1. Unpacking the shipment
Cut the safety straps, remove protective material and
unbox screws and legs

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
2. Prepare for mounting legs
Lift the seat and place two boxes, pallets or equivalent item under
each side. The bench must be raised minimum 350mm.
Raise min. 350mm
Raise min. 350mm

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
3. Legs mounting, step 1
Slide leg into corner of bench plate, making sure holes in
flange and bench are aligened

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
4. Legs mounting, step 2
After fitting the first leg, make sure to angle the other leg
before sliding into the corner

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
5. Legs mounting, step 3
Once each leg is fitted into corner of bench plate,
turn towards oppenent leg, and make sure square
flanges are parrallel.
Square flanges

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
6. Legs mounting, step 4
Use allen key (size 5) to mount 5 x M6x10mm bolts at each corner as shown
in right figure. The bolts are placed in a box, which comes with the shipment.
NB - make sure not to fully tighten the bolts until step 12.

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
7. Mount joint cover tubing, step 1
Turn one leg aside to make room for fitting joint cover tubing.
Slide tubing over the assembly plate.
Make sure the hole in joint cover tubing points towards
center of table.
Assembly plate
Joint cover
tubing

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
7. Mount joint cover tubing, step 2
Once fitted over the assembly plate, turn opponent leg back towards middle,
and make sure leg tubing fits closely to joint cover tubing.

24.01.2017#177 PLATEAU - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
8. Mount joint cover tubing, step 3
Below figures show correct position of assembly plates.
Assembly plate with M8 thread must point outwards.
Assembly plate with Ø12mm hole must point inwards.
Joint shown with joint cover tubing mounted
M8 thread
Ø12mm