Outsider LOOP CONE PLANTER User guide

01.03 2016
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
monting
instruction
loop cone plAnter / tAble / bAckrest
#169

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
02
index
• LOOP CONE PLANTER: PAGE 03
• LOOP CONE TABLE: PAGE 04-07
• LOOP CONE BACKREST: PAGE 08-10

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
Loop Cone (22 kg)
+ water up to the filling cap
(305 liters water) ~ 327 kg
or:
Loop Cone (22 kg)
+ sand up to the filling cap
(490 kg sand) ~ 512 kg
Ø1130mm
FILLED WITH WATER OR SAND / plAnter
Ø55mm
Each bracket is mounted to the
bottom of Loop Cone with
supplied M10x12 bolts.
Ø12mm
95mm
95mm
80mm
80mm
93mm
B11 BRACKET FOR SURFACE MOUNTING / plAnter
B11 BRACKET
3 x M10
03

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
Loop Cone (22 kg)
+ water up to the filling cap
(305 liters water) ~ 327 kg
or:
Loop Cone (22 kg)
+ sand up to the filling cap
(490 kg sand) ~ 512 kg
Ø1130mm
FILLED WITH WATER OR SAND / tAble
Ø55mm
Each bracket is mounted to the
bottom of Loop Cone with
supplied M10x12 bolts.
Ø12mm
95mm
95mm
80mm
80mm
93mm
B11 BRACKET FOR SURFACE MOUNTING / tAble
B11 BRACKET
3 x M10
04

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
1
2
3
The assembled brackets are mounted into the 3 inserts using
the M10 bolts and washers supplied.
Press the tabletop into the 3 rubber plugs in the bracket. Note
that the tabletop may require a sharp push to click into place.
Adjust the height as necessary to ensure that the tabletop is
flush with the edge of Loop Cone (see step 3, page 06).
MOUNTING THE TABLETOP USING THE BRACKETS SUPPLIED / tAble MOUNTING THE TABLETOP USING THE BRACKETS SUPPLIED / tAble
11
05

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
01.02 2016
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
06
MOUNTING THE TABLETOP USING THE BRACKETS SUPPLIED / tAble ADJUSTING THE TABLETOP W. FLEXIBLE ANGLE BRACKETS / tAble
The 3 angle brackets may be attached
in a number of positions to permit
horizontal adjustment of the tabletop.
Lift o the tabletop (see page 07)
before loosening the bolts and pushing
the bracket into a suitable position.
2
3
Begin by placing one of the 3 connectors into one of the 3 rub-
ber plugs. Then turn the tabletop to make the last 2 connectors
match the rubber plugs. Push the tabletop into all 3 plugs.
You will hear a click when the tabletop is pushed into the
correct position.

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
DISMANTLING THE TABLETOP FOR MAINTENANCE / tAble
The tabletop can be removed to adjust the height or to clean inside
Loop Cone. Position the tool level with one of the 3 plugs between
the tabletop and Loop Cone and tilt it to loosen the tabletop.
It is important to loosen all 3 plugs prior to lifting the tabletop.
Use a rag between the tool and the surface in order to protect your
products from marks and scratches. 07

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
08
ASSEMBLY WITH LOOP USING B13 ASSEMBLY BRACKET / bAckrest
1
2
3
5
4
Min. 30cm
3 x M10 3 x M10
ASSEMBLY WITH LOOP USING B13 ASSEMBLY BRACKET / bAckrest
NB: continued on page 09
1. Loop Cone is placed as shown (large diameter upwards) on a
non-damaging layer (e.g. a blanket).
2. In total 3 brackets (b13) is mounted on the inside of Loop
Cone with supplied M10 x12 bolts as shown above.
3. Loop is elevated at least 30cm above the ground (e.g. 3 EURO
pallets) as shown above. Remember non-damaging layer.
4. Loop Cone is lowered into the inner part of Loop.
5. B13 brackets are mounted in the recesses in the bottom of
Loop with supplied M10 x12 bolts.
1
2
3
4
5

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
09
6
8
7Loop Cone (22 kg)
+ water up to the filling cap
(305 liters water) ~ 327 kg
or:
Loop Cone (22 kg)
+ sand up to the filling cap
(490 kg sand) ~ 512 kg
FILLED WITH WATER OR SAND / bAckrest
Ø55mm
ASSEMBLY WITH LOOP USING B13 ASSEMBLY BRACKET / bAckrest
6. The assembly (Loop Cone + Loop) is elevated, turned and
placed on ground with the brackets facing downwards.
7. The brackets and assembly can be mounted to the ground.
Loop Cone can be filled with water or with sand, if mounting
is not possible or wanted.
6
7
8

01.03 2016#169 LOOP CONE PLANTER / TABLE / BACKREST - MOUNTING
out-sider a/s
Kigkurren 8A, Islands Brygge
DK-2300 Copenhagen S
[e-mail]
[phone]
www.out-sider.dk
10
CLEANING INSTRUCTIONS
The material polyethylene withstands almost all detergents.
Polyethylene requires no maintenance. The dyed polyethylene
preserves the colour - minimal fading by the sun is to be expected.
Pressure washers can be used with advantage to clean the product.
This service is often oered by companies that remove grati.
After cleaning, use vinyl polish (same as used for car interior) to
make the product shine.
SLIP RESISTANT SURFACES
The products have a textured/granulated surface due to abrasive
blasting of the mold.
This process increases friction, resulting in a less slippery surface.
TABLE TOP
The tabletop of the Loop Table features a smooth surface that re-
quires the same kind of maintenance as the other units.