Over Armour Offroad KU-X900-FC04 Installation manual

Over Armour Offroad
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of
Kubota RTV X900
Full Cab with Polycarbonate Windshield
KU-X900-FC04
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
1. Be sure to read these instructions thoroughly before opening and installing the Kubota
RTV X900 Full Cab with Aero-Vent Poly Windshield. The installation is best done
when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive
Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive
Velcro at room temperature prior to installation.
2. Carefully open the carton and remove the enclosure on a large flat surface that is clean
and free of dirt.
3. Check over the parts included in the carton with the parts list shown below:
Adhesive Velcro Hook Strips: 35 each------------3”
" " " " 6 each------------6"
“ “ ““4 each------------8”
“ “ ““2 each------------10”
“ “ ““2 each------------14”
“ “ ““2 each------------17”
“ “ ““1 each------------53”
Webbing straps with Grommet 2 each
Webbing Straps with Loops 2 each
Webbing Straps with Velcro 2 each
Cab Enclosure 4 panels
4. Install the Polycarbonate Windshield first as per the instructions provided with it.
5. Begin by installing the Rear Window. Along the bottom of the rear window is a 53” long
Velcro strip. This will attach to the shelf under the expanded metal cage and along the
top of the seat back. Take the 53” adhesive Velcro strip and adhere it up under the shelf
with the Velcro facing down. Then attach the bottom of the rear window making sure to
center it and keep it straight. The photo on the next page shows how it should fit.

6. Now pull the rear window up and attach it to the top bar across the back of the roll cage.
The top and sides of the rear window has double-sided Velcro sewn along the edges. At
each of these strips you will place a 3” adhesive Velcro strip on the inside of the bar to
hold the double-sided Velcro in place. The diagram below shows how to place the
Velcro.

7. The top of the rear window will attach to the bar as shown below:
8. Attach the sides of the rear window in the same fashion as shown in the photo below.
9. Now move on to the door panels. The top and front of the door has the same double-
sided strips as the rear window and attaches the same way. See photo below:

10. The back of the door has a cutout with a bungee cord across it. This spot has to go
around the metal block sticking out the sides of the vehicle. Placing the door here helps
line up the rest of the door so all the Velcro goes where they need to. See photo below:
11. Now work your way around the door attaching the double-sided Velcro under the
windshield and at the top rear corner of the door as shown below. The Velcro will go

under the rear window and the adhesive strips will be a bit crowded on the inside of the
bar and its ok if they overlap each other a bit.
12. The next step will be to adhere the 10” and 17” adhesive strips on the exposed roll cage
below the cutout with the bungee cord. The picture below show how it should be
attached.
13. Next take the 14” adhesive Velcro strips and attach them to the vehicle just under where
the roll cage ends down the front. See photo below:

14. Next step is to attach the rear of the door panel to the rear window and to the roll cage
just under the rear window. The two top tabs will attach right to the Velcro down the
sides of the rear window. The bottom tab will attach directly to the roll cage using an 8”
adhesive Velcro strip. See photo Below:

15. Now all that is left is to install the Top Cap over the cab. First take the two webbing
straps with the grommet holes and install then under the thumb nuts on the center bolt
holding the Windshield to the roll cage. See Photo Below
16. Then install the rear straps with the loop on the end. Run the strap around the end of the
brace behind the seat and through the loop in the end of the strap. See Photo Below
17. Now throw the Top Cap over the cab and attach it using the straps. Run the straps
through the ladder lock buckles as shown in the diagram below.

18. Once all four straps are in the buckles, pull them tight making sure to center the top and
that the front edge of the top is an inch or so below the holes across the top of the
windshield. Once the straps are pulled tight they should look like the picture below.
19. Lastly cut holes along the front of the top where each hole in the windshield is. Then bolt
the bent brace to the windshield with the Top Cap being sandwiched in between. When
finished it should look like the photo below.

Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date
item is received. You MUST package the product exactly as it was originally packaged from
the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes.
Lay all the windows on top of each other with the canvas folded in between and the paper (if
available) on both sides of the windows.
All returned products will be inspected upon arrival at the production facility and must be
in unused, factory new condition to receive refund - a 25% restocking fee will apply.
If ordered from Over Armour Offroad please call at 606-845-7439 to gain a return authorization
number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective,
you are responsible for paying the shipping to return the item.) Any returns submitted to Over
Armour Offroad without a return authorization number will be charged a 20% restocking
fee. If ordered from one of Over Armour Offroads many distributors’, you must first call them
and see what their return policy is. Once your item reaches our production facility, our customer
satisfaction team will inspect your item to ensure unused, factory new condition. NOTE: All
windshields must be returned with the original protective film intact and not removed. Do
NOT REMOVE if you have any intentions of returning the item. Refund/ replacement of a
windshield will only be processed on items with original protective film or if the windshield
is defective.
Items must be properly packaged in the original shipping carton to protect them during transit
and ensure your returned item arrives back factory fresh, and in new resalable condition (any
returned items that have been used, altered or damaged in any way will not be subject for a
refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will be approved.
Once returned items are received, credit will be issued to the original credit card/ payment
method used for the purchase. Outbound shipping and return shipping cost will not be refunded.
Please allow 4 to 6 weeks for your refund to be processed.

Warranty
To The Owner of this Product:
Thank you for purchasing one of Over Armour Offroad Cab Enclosures, Tops &/or Windshields!
Below are the terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or
windshield due to defect of the product. Please refer to the return policy in this case for more
information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will
gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for
the correction or replacement we will need to receive pictures of the defect in material or
workmanship along with the receipt from the date of purchase.
Thank you,
Over Armour Offroad
www.overarmouroffroad.com