Oxford Garden TRAVIRA MODULAR BASE User manual

15 Kingbrook Parkway, Suite 100 Simpsonville, KY 40067 p. 877.866.3331 f. 502.719.8888 oxfordgarden.com
Ver. 06.30.20
TRAVIRA MODULAR BASE
ASSEMBLY INSTRUCTIONS
COMPONENTS
HARDWARE CONNECTING HARDWARE
NOTE
To protect the finish surface of your unit from scratches, always assemble on top of provided cardboard box or a clean blanket.
Connector Bolt
Quantity: 1
Metal Washer
Quantity: 1
Lock Nut
Quantity: 1
Allen Wrench
Quantity: 1
D
E
F
G
Each base unit is equipped with built mounting brackets
attached to the bottom of the side panels. When connecting
2 or more units together, remove one bolt from bracket and
loosen the other bolt to rotate bracket 90 degrees.
See reverse for Travira Modular Base Assembly Instructions.
CONNECTING BRACKETS
Machine Bolts
Quantity: 14
Metal Washers
Quantity: 14
Allen Wrench
Quantity: 1
A
B
C

Ver. 06.30.20
INSTRUCTIONS
Attach LEFT SIDE PANEL to BACK PANEL using 3 washers
& bolts. NOTE: Leave bolts slightly loose to help with align-
ment of top.
CONNECT LEFT SIDE TO BACK PANEL
A
B
A
B
A
B
Attach RIGHT SIDE PANEL to BACK PANEL using
3 washers & bolts. NOTE: Leave bolts slightly loose to help
with alignment of top.
CONNECT RIGHT SIDE TO BACK PANEL
AB
AB
AB
Attach TOP to unit using 4 washers and bolts. Front of top
DOES NOT HAVE connector hole. NOTE: At this time firmly
tighten ALL INSTALLATION BOLTS on the unit.
CONNECT TOP TO SIDE ASSEMBLY
Connector Hole
faces unit side
A
B
A
B
A
B
A
B
Carefully
turn unit upside down, being careful not to scratch
the
top finish. Install either OPEN FLOOR GRATE (Option 1)
OR
TEKWOOD FLOOR PANEL (Option 2) to the unit using
4
washers and bolts.
INSTALL BOTTOM PANEL
OPEN FLOOR GRATE
(Option 1)
A
B
A
B
A
B
A
B
OR
TEKWOOD SLAT BOTTOM
(Option 2)
Return unit to its upright position. Insert the optional SLOTTED
SHELF , which rests firmly on the mid-support bars.
INSTALL SLATTED SHELF
Place optional TRASH BIN inside unit and install ACCESS
DOOR PANEL by aligning notched tabs on front opening
with tabs on the door panel. Push down to secure.
INSTALL TRASH BIN & ACCESS DOOR PANEL
8
8

Ver. 06.30.20
CONNECTING TWO OR MORE MODULAR UNITS
To secure 2 or more units together use both the preinstalled
CONNECTING BRACKETS found on the bottom of the base, and
the long connector bolt, washer, and lock nut included in the
hardware pack.
Lay units to be connected on their back on a clean, flat surface,
such as provided cardboard box or blanket, to protect the
surfaces from scratches. Remove one bolt from each bracket
and loosen the other bolt to rotate bracket 90 degrees. Align
brackets with holes on base of second unit and secure with
washer & bolt.
Join the top sections of the units together by inserting the
long connector bolt through the adjoining holes of two units.
Secure tightly using a washer and locking nut. Return joined
units to their upright standing position.
NOTE: For stability and safety, is essential that all units be
secured to each other at both top and bottom locations.
Place a small mark to indicate the center line of the DOOR
PANEL and the center of the LETTERING.
Carefully peel the
backing from the adhesive lettering, leaving the protective
strip on top of the letters.
Align bottom of protective strip
with front of door. Press lettering
firmly in place.
Burnish lightly and
remove the protective strip from the lettering.
Door Panel Center Line
APPLY OPTIONAL DOOR PANEL LETTERING
Lettering Center Line
BackingProtective Strip
Align Protective
Strip to front
of door.
Outside ViewInside View
Connector Hole

Ver. 06.30.20
SUGGESTED CONFIGURATIONS
Receptacle Base +
Shelf Base
Receptacle Base +
Shelf Base +
Hutch, L- Stack
2 Shelf Bases +
Hutch, L- Stack
Receptacle Base + Shelf
Base + 2 Hutch Units,
Double Stack
2 Shelf Bases +
2 Hutch Units,
Double Stack
2 Receptacle Bases +
2 Hutch Units,
Double Stack
Shelf Base +
Shelf Base
Receptacle Base +
Receptacle Base
Receptacle Base +
Hutch, Single Stack
Shelf Base +
Hutch, Single Stack