PacLights FFHL Series User manual

INSTALLATION GUIDE FFHL Series LED Flood
Instructions and specifications are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 1 of 4
Need help? (800) 988 -6386 Email: [e-mail] Website: www.PacLights.com
PL_INST_FFHL_v0
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
• Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone
sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and
unused conduit entries.
FFHL 500 FFHL 750 FFHL 1000
Connect the ACL and the ACN from the FFHL Fixture to the conduit with the AC power Supply Cable. Follow the Wiring Diagram provided.
AC POWER SUPPLY
FFHL DRIVER
GRAY (-)
PURPLE (+)
HOT [BLACK]
NEUTRAL [WHITE]
GROUND [GREEN]
WIRING DIAGRAM
DIM
INPUT
FFHL TRUNNION MOUNT
The Trunnion Mount is standard for all FFHL fixtures (Fig. 1).
FIG. 1
1
TRUNNION
MOUNT
FFHL FIXTURE
The FFHL Trunnion Mount drilling pattern (Fig. 2).
2
FIG. 2

INSTALLATION GUIDE FFHL Series LED Flood
Instructions and specifications are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 2 of 4
Need help? (800) 988 -6386 Email: [e-mail] Website: www.PacLights.com
PL_INST_FFHL_v0
FIG. 4
BOLT
FIG. 3
NUT
WASHER
WALL / SURFACE
HOLES
~
FFHL FIXTURE
The Trunnion Mount can be rotated. Loosen the center Cap Head
Screws (2) and remove the small Screws, Lockwashers, and Washers
at the sides of the FFHL fixture. Adjust the tilt angle of the FFHL
fixture to point towards the desired location. Reinstall and tighten
the Screws, Lockwashers, and Washers to hold the FFHL fixture in
place (Fig. 4).
4
TRUNNION
MOUNT
FFHL FIXTURE
SCREW
The Trunnion Mount can be mounted to a Wall/Surface. Align the
Trunnion Mount to the holes pre-drilled on the mounting surface and
bolt the fixture to the wall (appropriate mounting Bolts, Washers, and
Nuts not included) (Fig. 3).
3
FFHL TRUNNION MOUNT CONTINUED
FIG. 8
FIG. 7
FIG. 6
2
FFHL SLIPFITTER MOUNT WITH FLOOD MOUNT
The Slipfitter Mount can be mounted on a Round Pole (Ø2 3/8”) .
Run the FFHL Cable from the FFHL fixture and the Slipfitter Mount
to the Pole and follow the Wiring Diagram provided to properly install
the light fixture to the Power Supply Cable. Tighten the Slipfitter
Screws (4) to secure the FFHL fixture to the Round Pole (Fig. 8) .
4
SLIPFITTER
FFHL FIXTURE
ROUND POLE
POWER CABLE FFHL CABLE
SCREW
Install the Slipfitter to the Fixture Mount by mating the teeth and
run the Cable through. If needed to tilt the FFHL fixture simply
rotateand tighten the Socket Head Screw (Fig. 7) . Rotate the FFHL
fixture on the Flood Mount as needed (Refer to Fig. 4).
3
SCREW
SLIPFITTER
FFHL FIXTURE
FIXTURE
MOUNT
Install the Fixture Mount and Flood Mount (Note: The Flood Mount
has mounting holes correct for the Fixture Mount and dierent from
the Trunnion Mount) on the FFHL fixture and fasten them together
with the Screws, Washers, and Lockwashers (Fig. 6).
SCREWS
WASHERS
FIXTURE
MOUNT
FFHL FIXTURE
FFHL CABLE
FLOOD MOUNT
SCREWS
Before installing the Slipfitter Mount remove the Trunnion Mount by
removing the all Screws, Washers, and Lockwashers from the FFHL
fixture (Fig. 5).
1
FIG. 5
SCREWS
FFHL FIXTURE
TRUNNION
MOUNT

INSTALLATION GUIDE FFHL Series LED Flood
Instructions and specifications are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 3 of 4
Need help? (800) 988 -6386 Email: [e-mail] Website: www.PacLights.com
PL_INST_FFHL_v0
The Arm Mount drilling template is for either a Square or Round
pole (Fig. 10). Drill holes on the Square pole by following the Drilling
Template to mount the FFHL to the desired height (Fig. 11).
2
FIG. 10
The Arm Mount is available for all FFHL fixtures (Fig. 9). The Arm
Mount can be mounted on either a Square or Round pole.
1
FIG. 9
SIDE PLATE
ARM MOUNT
SCREWS
FFHL ARM MOUNT WITH FLOOD MOUNT
LOCKING PLATE
SQUARE POLE
GASKET
ROUND POLE
GASKET
WASHER
LOCK
WASHER
SCREW
If the FFHL fixture is being installed to a Square Pole, remove the
Round Pole Gasket (Fig. 12).
3
FIG. 12
FIG. 11
SQUARE
POLE
ROUND POLE
GASKET
ARM MOUNT
FIG. 13
FIG. 15 SCREW
LOCKING
PLATE
MOUNTING
POLE
POWER CABLE
Run the Power Cable through the Pole. Place the Locking Plate and
Gasket inside the Mounting Pole and fasten the FFHL fixture with
the Arm Mount onto the Pole with the Cap Head Screws (Fig. 15).
For the Round Pole, repeat Steps 2-4, except the remove the Square
Pole Gasket for Step 3. Reinstall the Side Plate (Refer to Fig. 13).
6
FIG. 14
FFHL CABLE
Before installing the Arm Mount remove the Trunnion Mount (Refer
to Fig. 5). Install the Flood Mount and the Fixture Mount (Refer to
Fig. 6). Run the FFHL Cable through the inside the Arm Mount.
Align the hole and teeth from the Arm Mount with the FFHL Fixture
Mount and use the Cap Head Screw to fasten them together at the
desired fixture tilt angle (Fig. 14). Rotate the FFHL fixture on the
Flood Mount as needed (Refer to Fig. 4)
5
FFHL FLOOD
MOUNT
SCREW
Remove the Screws (4) and the Side Plate from the Arm Mount
before installing the FFHL fixture (Fig. 13).
4
ARM MOUNT
ARM MOUNT
FFHL FIXTURE
FIXTURE
MOUNT

INSTALLATION GUIDE FFHL Series LED Flood
Instructions and specifications are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 4 of 4
Need help? (800) 988 -6386 Email: [e-mail] Website: www.PacLights.com
PL_INST_FFHL_v0
FFHL PHOTOCELL CONTROL & SECONDARY SURGE PROTECTOR
FIG. 16
The Junction Box (IP65) is required for the Photcell Control and the
Secondary Surge Protector. Remove the Screws (4) from the Cover
of the Junction Box. Remove the Knockout Plug(s) needed to install
the Photocell Control or Secondary Surge Protector (Fig. 16).
J-BOX
COVER
SCREW
1
JUNCTION
BOX
KNOCKOUT
PLUG
Install the Cable Glands with fastener Nuts where the Knockout
Plug(s) have been removed. Install the Photocell Control with a
Locknut. The Secondary Surge Protector can be placed inside the
J-Box (Fig. 17). All wiring must be installed by a certified electrician
and must be compliant to NEC standards.
PHOTOCELL
CONTROL
2
CABLE
GLANDS
FIG. 17
SURGE
PROTECTOR
NUT LOCKNUT