Palmgren 9682905 Instructions for use

Operating Instructions & Parts Manual EN
Grinder /
Sharpener
Machine
Model 9682905
9640516.01

PLEASE READ AND SAVE
THESE INSTRUCTIONS.
READ CAREFULLY
BEFORE ATTEMPTING
TO ASSEMBLE, INSTALL,
OPERATE OR MAINTAIN THE
PRODUCT DESCRIBED.
PROTECT YOURSELF AND
OTHERS BY OBSERVING ALL
SAFETY INFORMATION. FAILURE
TO COMPLY WITH INSTRUCTIONS
COULD RESULT IN PERSONAL
INJURY AND/OR PROPERTY
DAMAGE! RETAIN INSTRUCTIONS
FOR FUTURE REFERENCE.
PLEASE REFER TO BACK COVER
FOR INFORMATION REGARDING
PALMGREN’S WARRANTY
AND OTHER IMPORTANT
INFORMATION.
Model #: ___________________
Serial #: ___________________
Purch. Date: _______________
© 2017 Palmgren / a C.H. Hanson Brand
All Rights Reserved

3
GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
GETTING STARTED
Save this manual
You will need this manual for the safety warnings and
precautions, assembly instructions, operating and maintenance
procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover.
Keep this manual and invoice in a safe and dry place for future
reference.
Electrical requirements
The power supply to the Grinder / Sharpener Machine
needs to be 115V, 60Hz. The standard allowable
voltage variation is a plus or minus 10%.
UNPACKING
Open the shipping and product carton. After unpacking the
Grinder / Sharpener Machine inspect it carefully for any
damage that may have occurred during transit. Check for loose,
missing or damaged parts. If any damage or loss has occurred,
claim must be filed with the carrier immediately. Check for
completeness. Immediately report missing parts to dealer.
A list of items included with your machine is shown on page 4.
Inspect:
• All tools should be visually inspected before use, in
addition to regular periodic maintenance inspections.
• Be sure that the voltage labeled on the unit matches
your power supply.
• See General Safety Instructions, Cautions and
Warnings as shown.
SAFETY RULES
For your own safety, read all of the
instructions and precautions before
operating tool.
Always follow proper operating
procedures as defined in this manual even
if you are familiar with the use of this or similar tools.
Remember that being careless for even a fraction of a
second can result in severe personal injury.
PROPOSITION 65 WARNING: Some dust created by
using power tools contain chemicals known to the state
of California to cause cancer, birth defects or other
reproductive harm.
Some Examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry
products
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area and work with approved
safety equipment. Always wear OSHA/NIOSH approved, properly
fitting face mask or respirator when using such tools.
Preparing for your job
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses.
They are not safety glasses.
• Wearing an OSHA/NIOSH approved, properly fitting face
mask or respirator is highly recommended.
• Wear proper apparel when using power tools. Do not wear
loose clothing, gloves, neckties, rings, bracelets or other
jewelry which may get caught up in moving parts of machine.
• When using power tools, wear protective hair covering to
contain long hair.
• Wear safety shoes with non-slip soles.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
Preparing the work area for your job
• Keep work area clean. Cluttered work areas invite accidents.
• Do not use the Grinder / Sharpener Machine in dangerous
environments or where explosive fumes exist. Do not use
the machine in damp or wet locations. Do not expose power
tools to rain.
• Work area should be properly lighted.
• Proper electrical receptacle should be available for tool.
Three-prong plug should be plugged directly into properly
grounded three-prong receptacle.
• Extension cords should have a grounding prong and the
three wires of the extension cord should be of the proper
gauge.
• Keep visitors at a safe distance from work area.
• Keep children out of workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to
prevent any unintentional use of power tools.
Maintaining your tool
• Always unplug tool and remove it from its power source prior
to inspection. Never unplug the tool by pulling on the cord.
• Consult this manual for specific maintaining and adjusting
procedures.
• Keep the tool clean for safest operation. Chip debris build
ups can become combustible.
• Check for damaged parts. A part that is damaged should
be properly repaired or replaced. Do not perform makeshift
repairs. (Use the parts list in this manual to order repair
parts). Repairs must be made by a qualified technician.
• Never operate the machine without all safety guards in place.
Bypassing, deactivating or removal of a safety device in any
way endangers you.

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
4
Ref. No Qty. Description
1 5
Collet type, DIN 6341 – G=S20x2, d=20, D=28, L=137, 35°
Sizes – 4mm ; 6mm ; 8mm ; 10mm ; 12mm
2 1 Corundum cup wheel 100mm x 50mm x 20mm – Diamond cup wheel 100mm x 50mm x 20mm (mounted on the
machine when delivered)
3 1 Spare round belt
4 1 Socket to mount the cup wheels
5 1 Accessory to grind turning tools
6 1 Accessory to grind end mills
7 1 Accessory to grind twist drills
8 1 Clamping ring for the device twist drill
9 1 Clamping piece for the device twist drill
10 1Crank to tighten the collet chuck
11 2Hook clamp wrenches (38mm and 42mm) to tighten the collet chuck seat
12 1Tool carrier shaft tension knob
13 5Allen key wrenches
14 2Screwdrivers
Accessories and tools included with your Grinder / Sharpener Machine
1.
2.
3.
13.
14.
4.
5.
6.
7.
9.
8.
11.
12.
10.
GETTING STARTED

5
GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
SAFETY RULES (CONTINUED FROM PG.3)
Know how to use your tool
Dusty work environments may be
hazardous to your health. Always wear a
OSHA/NIOSH approved, properly fitting face mask or
respirator.
The operation of any power tool can result
in foreign objects being thrown into the
eyes, which can result in severe eye damage. Always wear
safety goggles complying with United States ANSI Z87.1.
Think safety! Safety is a combination of
operator common sense and alertness at
all times when tool is being used.
• The Model 9682905 Grinder / Sharpener Machine is
designed and intended for use by properly trained operators.
You must be familiar with the proper and safe operation of
a Grinders / Sharpener Machine. Obtain proper training and
knowledge before operating this machine.
• Ensure the grinding wheel is solid and free from any flaws or
cracks. You can perform a ring test by holding the grinding
wheel with a wooden dowel rod through the arbor hole and
lightly striking it with a wrench or hammer. The wheel should
emit a clear “ping” sound. A damaged wheel will emit a dull
sound. If there is any doubt of a wheel’s condition, replace it
immediately.
• A damaged wheel is more likely to fly apart or explode
upon machine start up. Do not stand in line with the wheel’s
rotation upon start up.
• Grinding wheels operated at a speed faster than they are
rated for can fly apart or explode causing injury or death.
Before mounting a new wheel make sure the wheel’s RPM
rating is equal to or more than the machine’s RPM rating.
• Heavy impact with a workpiece or trying to make a very deep
cut can cause a wheel to break apart or explode. Do not jam
a workpiece into the wheel to reduce this risk.
• Use the right tool for the job. Do not force a tool or
attachment to do a job for which it was not designed.
• Remove adjusting keys and wrenches. Form a habit of
checking to see that keys and adjusting wrenches are
removed from the machine before turning it on.
• To reduce the risk of electrical shock, never use the tool in
rain or wet environments. Store the tool indoors.
• Turn the tool off immediately in the case of an emergency.
Completely remove the tool from its power source before
attempting to fix the issue.
• Never leave the machine running while it is unattended. Turn
off the power and stay with the machine until it comes to a
complete, full stop.
• Use recommended accessories. Understand and obey all
safety instructions supplied with accessories. The use of
improper accessories may cause injury.
• Make sure that the any hazardous dusts created by grinding
and sharpening are removed by a dust extraction unit.
• Never connect a this machine to a dust collection system
also being used by woodworking machines. The sparks
and hot chips from this machine can quickly ignite the
woodworking dust cause fire or an explosion.
• Some materials such as magnesium, titanium and aluminum
have flammable properties. Consult with the supplier of these
materials for information on safe grinding procedures.
SPECIFICATIONS
Model 9682905 Grinder / Sharpener Machine
Power 115V, 60Hz
Speed Cup Wheel,
Diamond Cup Wheel
5,000 RPM
Max. Grinding Speed 114 FPS
Speed Motor 2,750 RPM
Adjustable Angles
Vertical / Rear 0- 40°
Horizontal / Taper Grinding 0-180°
Negative 0- 52°
Setting Positions Rotation
Angle
15°
180°
Capacities
Tool Holder Travel Length 5.5”
Fine Adjustment Range Of
The Tool Holder
0.070”
Fine Adjustment Range Of
The Length Axis
0.23”
Division Scale Infeed 0.00039”
Grinding Cup Wheels
Corundum Cup Wheel 0100 x 50 x 020
Diamond Cup Wheel 0100 x 50 x 020
Grinding Accessory Capacities
Single Edge Milling Cutter Up to 0.47” in dia.
Turning Tool Up to 0.82” x 0.82”
Drill Bit Up to 0.47 in dia.
End Mill Cutter Up to 0.47” in dia.
Collets 1/8” to 1/2”
Dimensions H X D X W 13.4” x 17.7” x 13.7”
Net Weight 110 lbs.
ASSEMBLY / INSTALLATION
Environmental requirements
The Model 9682905 Grinder / Sharpener machine should be
operated in temperatures of 41˚ to 95˚F and humidity range of
25% to 80%.
Power source
The motor is designed for operation on the voltage and frequency
specified. Normal loads will be handled safely on voltages not
more than 10% above or below specified voltage.

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
6
ASSEMBLY / INSTALLATION (CONTINUED)
Power source
Running the unit on voltages which are not within the range may
cause over heating and motor burn-out. Heavy loads require that
the voltage at the motor terminals be no less than the voltage
specified.
Electrical connections
Make sure the tool is off before plugging it
into a power source to prevent accidental
starts.
Do not permit fingers to touch the
terminals of plug when installing or
removing from outlet.
Electrical safety
• Double insulated tools are equipped with a polarizing three
pronged plug (one blade is wider than the other.) This plug
will fit in a polarized outlet only one way. If the plug does not
fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do
not change the plug in any way.
• Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
Before plugging in the tool, be certain the outlet voltage
supplied is within the voltage marked on the nameplate.
• Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is grounded. If operating
the power tool in damp locations is unavoidable, a Ground
Fault Circuit Interrupter must be used to supply the power to
your tool. Rubber soled footwear will further enhance your
personal safety.
4. Don’t expose this or any tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock
5. Do not abuse the cord. Never use the cord to carry the tool
or pull the plug from an outlet. Keep cord away from heat,
oil, sharp edges or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric
shock.
Extension cords
• The use of an extension cord will cause some drop in voltage
and loss of power.
• Wires of the extension cord must be of sufficient size to carry
the current and maintain adequate voltage.
• Use the table to determine the minimum wire size (A.W.G)
extension cord.
• Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.
• If the extension cord is worn, cut or damaged in any way,
replace it immediately.
Extension length
Wire Size A.W.G.
Up to 25 ft 16
25 to 100 ft 14
NOTE: Using extension cords over 100 ft long is not
recommended.
Locating the machine
The Model 9682905 Grinder / Sharpener Machine should
be mounted on a suitable bench or stand. For optimum
performance, it is recommended the supporting device and
machine be leveled.
• Make certain any supporting stands or benches can hold the
machine since it weighs over 100 lbs. It is recommended the
machine be moved with a suitable hoist, forklift or carefully
lifted by two people. Do not stand under the machine while it
is being lifted or suspended.
• Locate the machine where it is easy to remove the power
plug and is easily accessible for maintenance.
Inserting the tool carrier shaft tension knob
1. Locate the Tool Carrier Shaft Tension Knob from the supplied
items.
2. Insert the knob into the hole on the lower left front portion of
the tool and slightly tighten it.
3. The knob acts as a stop and limits the rotation of the tool
carrier shaft under tension.
Assembling the drill bit clamping accessory
12
Clamping ring
Clamping
ece
Clamping Ring
Clamping
Piece
The Model 9682905 Grinding / Sharpener can sharpen v-blade
mill bits (burins), end mills, twist drill bits and lathe cutters with
the use of accessories that attach to the Grinder / Sharpener
machine. The Drill Bit Grinding Accessory requires minor
assembly before use.
1. Insert the clamping ring end into the Drill Bit Grinding
Accessory.
2 Tighten the small thumb screw to hold the ring into the
accessory.

7
GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
OPERATION - MODEL 9682905 GRINDER / SHARPENER - FUNCTIONAL PARTS
12. Diamond
dressing tool
14. Grinding shaft
clamping knob
11. Diamond disc
(Extra corundum
disc included)
10. Locking
bayonet lever
9. Tool
carrier
head
7. Tool carrier
head vertical
axis clamping
lever
8. Tool carrier
head in and out
adjustment
6. Tool carrier
shaft clamping
lever
13. Tool carrier
head horizontal
rotation axis
clamping lever
5. Tool
carrier
shaft
3. Tool carrier
shaft lock
knob 4. Oil ports
2. Tool carrier
shaft lateral
movement
knob
1. Knob to
shift grinding
wheel laterally
1. Knob to shift grinding wheel laterally
Turning this knob moves the grinding wheel laterally, left-to-
right from the operator’s viewpoint.
2. Tool Carrier Shaft Lateral Movement Knob
Turning this knob moves the tool carrier left-to-right along the
tool carrier shaft.
3. Tool Carrier Shaft Tension Knob
Tightening this knob puts tension on the carrier shaft. Pulling
back on the carrier head rotates the shaft to a retractable stop
point.
4. Oil Ports
Maintain the tool by oiling the moving parts through these
ports.
5. Tool Carrier Shaft
The tool carrier clamps on this bar, laterally and rotationally.
6. Tool Carrier Shaft Clamping Lever
The lever locks the tool carrier along the carrier shaft. The
shaft still has a retractable spring load applied to it based on
the Lateral Shaft Movement Knob, #12.
7. Tool Carrier Head Vertical Axis Clamping Lever
The lever locks the carrier head in a fixed position. Loosen the
lever and the head will rotate vertically, left-and-right (like a
clock dial) from the operator’s viewpoint.
8. Tool Carrier Head in and out adjustment
Turning the thumb screw on the left advances the carrier head
in-and-out from the operator’s viewpoint.
9. Tool Carrier Head
The twist drill bit, end mill and lathe accessories work in
conjunction with the head. The twist drill bit accessory inserts
into the collet portion of the head. The end bit and lathe
accessories replace the head completely.
10. Locking Bayonet Lever
The lever has three settings that control the rotation of the
collet holding the bit being sharpened.
11. Diamond Cup Wheel (extra corundum disc included)
When replacing the cup wheel, make sure the new wheel
meets or exceeds the machine’s RPM rating.
12. Diamond Dressing Tool
Flip the dressing bracket over to engage the diamond tool to
the grinding wheel. Dressing the wheel creates a flat grinding
surface.
13. Tool Carrier Head horizontal rotation axis clamping lever
The lever locks the carrier head in a fixed position. Loosen the
lever and the head will rotate horizontally, left-and-right from
the operator’s view.
14. Grinding Shaft Clamping Knob
Tightening this knob locks and prevents the grinding wheel
from being adjusted laterally, left-to-right.

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
8
OPERATION - MODEL 9682905 GRINDER / SHARPENER -
FUNCTIONAL PARTS (CONTINUED)
14. Locking Bayonet Lever
The lever has three settings that control the rotation of the
collet holding the bit being sharpened.
15. Collet Clamp Handle
After a collet has been inserted into the tool carrier head,
the collet clamp handle is also inserted. The item being
sharpened is inserted into the collet. The clamp handle is
rotated clockwise to hold the item for sharpening.
16. Tool Carrier Head Lateral Adjustment Knob
Turning this knob moves the entire Tool Carrier Head left and
right based on an operators viewpoint.
17. Tool Carrier Head Removal Knob
Loosening this knob allows the operator to remove the Tool
Carrier Head completely. Some accessories require removal
and replacement of the head.
18. Relief Angle Scale
Shows the angle of the tool carrier head in relation to the
grinding disc.
19. Tool Carrier Shaft Lock Knob
This knob completely locks the tool carrier shaft and
prevents it from rotating.
OPERATION - GENERAL
Dusty work environments may be
hazardous to your health. Always wear a
OSHA/NIOSH approved, properly fitting face mask or
respirator.
The operation of any power tool can result
in foreign object being thrown into the
eyes, which can result in severe eye damage. Always wear
safety goggles complying with United States ANSI Z87.1.
Wear proper apparel when using this tool.
Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught up in moving parts of machine.
The on / off switch
The on / off switch is located on
the upper left side of the tool. To
open the switch cover, rotate the
red mushroom shaped emergency
kill button:
1. Rotate the red “emergency
kill” button to open the yellow
power switch box.
2. Push the green button to start
the tool.
3. Push the red button to stop the tool.
The cup wheel on the Grinder / Sharpener will continue
to rotate for approximately 30 seconds after the tool is
turned off.
4. For an emergency stop, push the red “mushroom shaped”
button.
OPERATION - ACCESSORY ATTACHMENTS
Make sure all workpieces being sharpened
or ground are held securely in the
accessory attachments. Workpieces not secured can be
“grabbed” by the tools cup wheel and thrown violently. Never
hold a workpiece by hand.
The Model 9682905 Grinding / Sharpener can sharpen v-blade
mill bits (burins), end mills, drill bits and lathe cutters with the use
of accessories that attach to the Grinder / Sharpener machine.
These accessories come supplied with the machine and work in
conjunction with the Tool Carrier Head.
Once the workpiece (or accessory holder clamping the
workpiece) being sharpened is correctly secured into the Tool
Carrier Head, the various angles and positions for sharpening
can be achieved by setting the tool’s components.

9
GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
OPERATION - DRILL BIT SHARPENING
ACCESSORY
Before installing any accessories to the
machine, make sure the machine is turned
off and unplugged completely from its power source.
Installing the twist drill bit accessory into the tool
carrier head
There is no need to remove the Tool Carrier Head for single edge
burin bits. To sharpen a single edge bit, insert it into the collet and
tightening the collet with the Collet Crank Handle.
Likewise, you do not have to remove the Tool Carrier Head
to sharpen a twist drill bit. To sharpen a bit use the Drill Bit
Accessory and follow the steps below.
1. Remove the stop from the bushing on the Tool Carrier Head.
2. Insert the small shaft of the twist drill bit accessory into the
bushing hole. The larger shaft fits into the collet.
3. Insert and tighten the collet with the Collet Crank Handle
4. Insert the twist drill bit into the accessory holder and move
the ring up so the bit is close to the cup wheel
5. Make the final angle and distance adjustments using the
Grinder / Sharpener’s components.
Installing the end mill accessory onto the tool carrier
To use the mill end accessory, it is necessary to remove the tool
carrier head and replace it with the end mill accessory.
1. Release the Tool Carrier Head horizontal rotation axis
clamping lever.
2. Loosen the knurled screw on the right side of the of the Tool
Carrier Head. The head will slide off it the tool carrier. Make
certain to retain the wedge key.
5. Slide the end mill accessory onto the tool carrier. Make sure
the wedge key is in its proper position. Tighten the knurled
screw on the right side of the accessory.
6. Insert the end mill into the collet and tighten it.
7. Adjust the flute rotation control pointer to that the end mill can
rotate as it is being sharpened.
8. Make the final angle and distance adjustments using the
Grinder / Sharpener’s components.
Installing the lathe tool accessory onto the tool
carrier
To use the lathe cutter accessory, it is necessary to remove the
Tool Carrier Head and replace it with the lathe cutter accessory.
1. Release the Tool Carrier Head horizontal rotation axis
clamping lever.
2. Loosen the knurled screw on the right side of the of the tool
carrier head. The head will slide off it the tool carrier. Make
certain to retain the wedge key.
5. Slide the end mill accessory onto the tool carrier. Make sure
the wedge key is in its proper position. Tighten the knurled
screw on the right side of the accessory.
6. Insert the end mill into the collet and tighten it.
NOTES

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
10
TROUBLESHOOTING GUIDE
MAINTENANCE / REPAIR
WIRING DIAGRAM - MODEL 9682905 GRINDER / SHARPENER
Symptom Possible Cause(s) Corrective Action
Motor rotates in the wrong direction Electrical lead wires reversed Reverse any of the two
electrical leads L1, L2
or L3.
Grinding operations yield loose
tolerances
Loose handles
Check and tighten handles “A” and “B” to
remove “play” from the settings

GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
11
MAINTENANCE
Make sure the machine is turned off and
completely unplugged from its power
source before performing any type of maintenance.
The type and extent of machine wear will depend on
the frequency of use and service conditions. Below are
recommendations.
• On a daily basis before using the tool, carefully inspect the
grinding cup for any damage. If any doubt exists or if the cup
appears damaged or shows cracks replace it immediately.
• Regularly clean the machine to remove any left over grinding
dust. Leftover debris in the slideways can cause the machine
to wear prematurely. If necessary use compressed air to
clean the machine. The use of a proper fitting OSHA/NIOSH
face mask or respirator is highly recommended.
• If slack or play is noticed in the slideways tighten the
appropriate adjusting screws.
• Oil the lubrication nipples at regular intervals.
NOTES

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
12
For Repair Parts, call 1-800-Grainger 24 hours a day – 365 days a year
Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list
REPAIR PARTS ILLUSTRATION FOR MODEL 9682905 - GRINDER / SHARPENER MACHINE

GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
13
REPAIR PARTS LIST FOR MODEL 9682905 - GRINDER / SHARPENER MACHINE
Ref.
No. Description Part No. Qty.
Ref.
No. Description Part No. Qty.
1Hand Scale Wheel 9640517.01 1
2Screw M6x12 * 3
3Lower Indicating Dial 9640518.01 1
4Holder 9640519.01 1
5Screw M8x70 * 2
6Spring 9640520.01 1
7Hex Nut M8 * 1
8Shaft 9640521.01 1
9Machine Foot 9640522.01 4
10 Cover 9640523.01 1
11 Handle 9640524.01 1
12 Grub Screw 9640525.01 1
13 Oil Cup 9640526.01 4
14 Base 9640527.01 1
15 Belt 9640528.01 1
16 Motor 9640529.01 1
17 Graduation Hand Wheel 9640530.01 1
18 Screw M6x16 * 2
19 Screw M6x25 * 2
20 Screw M6 * 3
21 Screw M4 * 4
22 Upper Indicating Dial 9640531.01 1
23 Ring 9640532.01 1
24 Screw M8x15 * 1
25 Grub Screw 9640533.01 1
26 Screw M6 X 3 * 1
27 Locking Handle 8640534.01 1
28 Grinding Unit Assembly 9640535.01 1
29 12 V Led Lamp 9640536.01 1
30 Motor Flange 9640537.01 1
31 Screw M5x16 * 7
32 Subordinate Driving Wheel 9640538.01 1
33 Thick Gasket 9640539.01 1
34 Screw M4x14 * 1
35 Cover 9640540.01 1
36 Thrust Ball Bearing 51100 * 2
37 Pin 9640541.01 1
38 Holder 9640542.01 1
39 Finisher Fixing Screw 9640543.01 1
40 Universal Clamp Holder 9640544.01 1
41 Electromagnetic Switch 9640545.01 1
42 Nut Cover 9640546.01 1
43 Driving Gasket 9640547.01 1
44 Grease Seal 9640548.01 1
45 Driving Head 9640549.01 1
46 Locking Round Nut 9640550.01 2
47 Bearing 9640551.01 3
48 Spindle Cover 9640552.01 1
49 Sealing Ring 9640553.01 1
50 Shaft 9640554.01 2
51 Ring 9640555.01 1
52 Ring 9640556.01 1
53 Washer 9640557.01 1
54 Flange 9640558.01 1
55 Asbestos Gasket 9640559.01 2
56 Screw M6 X25 * 1
57 Gasket 9640560.01 1
58 Grinding Wheel 9640561.01 1
59 Flange 9640562.01 1
60 Screw 9640563.01 1
61 Screw M8x60 * 1
62 Screw M6x30 * 1
(∆) Not Shown (*) Standard hardware item available locally (N/A) Not available as replacement part

MAINTENANCE / REPAIR TROUBLESHOOTING OPERATION ASSEMBLY / INSTALLATION SAFETY / SPECIFICATIONS GETTING STARTED
14
For Repair Parts, call 1-800-Grainger 24 hours a day – 365 days a year
Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list
REPAIR PARTS ILLUSTRATION FOR MODEL 9682905 - GRINDER / SHARPENER MACHINE ACCESSORIES
AC
B

GETTING STARTED SAFETY / SPECIFICATIONS ASSEMBLY / INSTALLATION OPERATION TROUBLESHOOTING MAINTENANCE / REPAIR
15
REPAIR PARTS LIST FOR MODEL 9682905 - GRINDER / SHARPENER MACHINE
ACCESSORIES
(∆) Not Shown (*) Standard hardware item available locally (N/A) Not available as replacement part
Ref.
No. Description Part No. Qty.
Ref.
No. Description Part No. Qty.
FIXTURE A
1Tool Holder 9640570.01 1
2Screw Dole 9640571.01 1
3Pressure Plate 9640572.01 1
4Fixed Plate 9640573.01 1
5Flat Washer 9640574.01 1
6Flat Washer 9640575.01 1
7Hexagon Nut 9640576.01 2
8Screw M6x16 * 2
9Screw M4x10 * 3
10 Guide Sleeve 9640577.01 1
FIXTURE B
1Slide Bracket 9640578.01 1
2Fastning Set 9640579.01 1
3Telescopic Cylinder 9640580.01 1
4Stator 9640581.01 1
5Locate Strut 9640582.01 1
6Fixed Block 9640583.01 1
7Fastning Block 9640584.01 1
8Guide Pole 9640585.01 1
9Screw M6x25 * 4
10 Screw M6x16 * 4
11 Screw M6x10 * 4
12 Knife Grinder Chuck 9640586.01 1
13 Oil Cup 9640587.01 1
14 Screw M5x20 * 1
15 Hex Nut M5 * 1
16 Handle 9640588.01 1
17 Grip 9640589.01 1
18 Shaft 9640590.01 1
FIXTURE C
1Guide Plate 9640591.01 1
2Clamping Rod 9640592.01 1
3Knife Block 9640593.01 1
4Clamping Block 9640594.01 1
5Locate Block 9640595.01 1
6Fixed Shaft 9640596.01 1
7Shaft 9640597.01 1
8Screw M6x14 * 1
9Screw M6x12 * 1
10 Screw M4x8 * 1
11 Fixed Block 9640598.01 1
12 Lock Screw 9640599.01 1
13 Lock Hander 9640600.01 1
14 Limit-Stop Screw 9640601.01 1
15 Lock Set 9640602.01 1
16 Locate Strut 9640603.01 1
17 Clamping Lever 9640604.01 1
REPLACEMENT WHEELS, COLLETS & ACCESSORIES
Complete Kit of Collets Type 355E,
DIN 6341 Size 4mm ; 6mm ; 8mm ;
10mm ; 12mm
9640564.01 1
Complete Kit of Collets Type 385E,
DIN 6341 Size 4mm ; 6mm ; 8mm ;
10mm ; 12mm
9640565.01 1
Replacement Aluminum grinding
wheel 0100 x 50 x 020
9639710.01 1
Replacement diamond grinding
wheel 0100 x 50 x 020
9639711.01 1
Spare Round Belt 9640568.01 1
Socket to Mount the Cup Wheels 9640569.01 1

PALMGREN WARRANTY
C.H. Hanson / Palmgren warrants their products to be free of defects in material or
workmanship. This warranty does not cover defects due directly or indirectly to misuse,
abuse, normal wear and tear, failure to properly maintain the product, heated, ground or
otherwise altered, or used for a purpose other than that for which is was intended.
The warranty does not cover expendable and/or wear part (i.e. v-belts, screws, abrasives,
jaws), damage to tools arising from alteration, abuse or use other than their intended
purpose, packing and freight. The duration of this warranty is expressly limited to the terms
noted below beginning from the date of delivery to the original user.
The Palmgren branded items carry the following warranties on parts:
All vises, clamps, positioning tables, tombstones, jack screws and vise
accessories - LIFETIME.
All bench grinders, drill presses, tapping machines, band saws, lathes, milling
machines, arbor presses, abrasive finishing machines and work stands -
3 YEARS.
The obligation of C.H. Hanson / Palmgren is limited solely to the repair or replacement, at
our option, at its factory or authorized repair agent of any part that should prove inoperable.
Purchaser must lubricate and maintain the product under normal operating conditions at
all times. Prior to operation become familiar with product and the included materials, i.e.
warnings, cautions and manuals.
Failure to follow these instructions will void the warranty.
This warranty is the purchaser’s exclusive remedy against C.H. Hanson for any inoperable
parts in its product. Under no circumstances is C.H. Hanson liable for any direct, indirect,
incidental , special or consequential damages including loss of profits in any way elated to
the use or inability to use our products. This warranty gives you specific legal rights which
may vary from state to state.
Palmgren - a C.H. Hanson Company
2000 N. Aurora Rd., Naperville, IL 60540 U.S.A.
or call 1-800-827-3398