Panasonic TY-ER3D5MA User manual

Operating Instructions
3D Eyewear
Model No. TY-ER3D5MA
This product cannot be used as sunglasses.
ENGLISH
繁體中文
7,1*9,7
日本語
TQZJ405

Parts name and functions
_ST60_ST60X_
[Front side] [Back side]
_ST60_ST60X_
Power button
Switches the 3D Eyewear on or off.
_ST60_ST60X_
Press the button for about 1 second to turn the power on. The indicator
lamp lights for about 2 seconds and then goes off.
To turn the power off, press the button for about 2 second again. The
indicator lamp flashes 3 times, then the 3D Eyewear turns off
_ST60_ST60X_
Mode
_ST60_ST60X_
Press the button for about 1 second to change the mode between 3D
and 2D (view a 3D image in 2D).
(When power is off) Press the button for 5 second to change to
registration mode.
_ST60_ST60X_
Indicator lamp
Lights or flashes during use to show the status. (see below)
_ST60_ST60X_
Protection film
Peel off the protection film on both side of the lens.
Insulating sheet
Battery cover
_ST60_ST60X_
When using for the first time, remove the insulating sheet. Pull the
insulating sheet.
[Front side] [Back side][Front side][Front side] [Back side][Back side]
Power button
Switches the 3D Eyewear on or off.
Power button
Switches the 3D Eyewear on or off.
Press the button for about 1 second to turn the power on. The indicator
lamp lights for about 2 seconds and then goes off.
To turn the power off, press the button for about 2 second again. The
indicator lamp flashes 3 times, then the 3D Eyewear turns off
Press the button for about 1 second to turn the power on. The indicator
lamp lights for about 2 seconds and then goes off.
To turn the power off, press the button for about 2 second again. The
indicator lamp flashes 3 times, then the 3D Eyewear turns off
ModeMode
Press the button for about 1 second to change the mode between 3D
and 2D (view a 3D image in 2D).
(When power is off) Press the button for 5 second to change to
registration mode.
Press the button for about 1 second to change the mode between 3D
and 2D (view a 3D image in 2D).
(When power is off) Press the button for 5 second to change to
registration mode.
Indicator lamp
Lights or flashes during use to show the status. (see below)
Indicator lamp
Lights or flashes during use to show the status. (see below)
Protection film
Peel off the protection film on both side of the lens.
Insulating sheet
Battery cover
Protection film
Peel off the protection film on both side of the lens.
Insulating sheet
Battery cover
When using for the first time, remove the insulating sheet. Pull the
insulating sheet.
When using for the first time, remove the insulating sheet. Pull the
insulating sheet.
1 (0100802)

_ST60_ST60X_
Indicator lamp status
_ST60_ST60X_
Indicator lamp Status
Lights red for 2 seconds when turned
on
Sufficient battery level
Flashes 5 times when turned on Low battery level
Flashes red Under registering
Flashes red once every 1 seconds Under reconnecting to the TV
Lights red for 3 seconds Registering or reconnecting is
successfully completed.
Flashes red 3 times Power off
(Press the button over 2 seconds
when in use, or Automatically power
off when registering or connecting
fails, or connection is lost)
Flashes red once every 2 seconds
when in use
3D mode is selected
Flashes red twice every 4 seconds
when in use
2D mode is selected
Indicator lamp statusIndicator lamp status
Indicator lamp Status
Lights red for 2 seconds when turned
on
Sufficient battery level
Flashes 5 times when turned on Low battery level
Flashes red Under registering
Flashes red once every 1 seconds Under reconnecting to the TV
Lights red for 3 seconds Registering or reconnecting is
successfully completed.
Flashes red 3 times Power off
(Press the button over 2 seconds
when in use, or Automatically power
off when registering or connecting
fails, or connection is lost)
Flashes red once every 2 seconds
when in use
3D mode is selected
Flashes red twice every 4 seconds
when in use
2D mode is selected
2 (0100802)

Watching TV
3D
Registration
_ST60_ST60X_
First registration
Perform the first registration when the 3D Eyewear is used for the first time.
_ST60_ST60X_
1Turn the TV on
2Press the button for about 1 second to turn the power on.
The LED lights for about 2 seconds and then goes off.
The 3D Eyewear will be turned on and start registration.
Place the 3D Eyewear within 50 cm from the TV while registration in
progress.
3The red LED lights on the 3D Eyewear for 3 seconds when the
registration is successfully completed
After first registration, the 3D Eyewear will reconnect with TV
automatically when 3D Eyewear is turned on near the TV in 3D mode.
_ST60_ST60X_
Registration again
When connection with registered TV fails, or when using with another TV,
re-register the 3D Eyewear.
_ST60_ST60X_
1Turn the TV on
2Within 50 cm from the TV, press the button for about 1 second to
turn the power on.
The LED lights for about 2 seconds and then goes off.
_ST60_ST60X_
Release the power switch when registration starts.
_ST60_ST60X_
3The red LED lights for 3 seconds when the registration is
successfully completed
First registration
Perform the first registration when the 3D Eyewear is used for the first time.
First registration
Perform the first registration when the 3D Eyewear is used for the first time.
1Turn the TV on
2Press the button for about 1 second to turn the power on.
The LED lights for about 2 seconds and then goes off.
The 3D Eyewear will be turned on and start registration.
Place the 3D Eyewear within 50 cm from the TV while registration in
progress.
3The red LED lights on the 3D Eyewear for 3 seconds when the
registration is successfully completed
After first registration, the 3D Eyewear will reconnect with TV
automatically when 3D Eyewear is turned on near the TV in 3D mode.
1Turn the TV on
2Press the button for about 1 second to turn the power on.
The LED lights for about 2 seconds and then goes off.
The 3D Eyewear will be turned on and start registration.
Place the 3D Eyewear within 50 cm from the TV while registration in
progress.
3The red LED lights on the 3D Eyewear for 3 seconds when the
registration is successfully completed
After first registration, the 3D Eyewear will reconnect with TV
automatically when 3D Eyewear is turned on near the TV in 3D mode.
Registration again
When connection with registered TV fails, or when using with another TV,
re-register the 3D Eyewear.
Registration again
When connection with registered TV fails, or when using with another TV,
re-register the 3D Eyewear.
1Turn the TV on
2Within 50 cm from the TV, press the button for about 1 second to
turn the power on.
The LED lights for about 2 seconds and then goes off.
1Turn the TV on
2Within 50 cm from the TV, press the button for about 1 second to
turn the power on.
The LED lights for about 2 seconds and then goes off.
Release the power switch when registration starts.Release the power switch when registration starts.
3The red LED lights for 3 seconds when the registration is
successfully completed
3The red LED lights for 3 seconds when the registration is
successfully completed
3 (0100806)

Watching TV
3D
Replacing the battery
_ST60_ST60X_
When the battery is running low, the indicator lamp flashes 5 times on turning
the 3D Eyewear on.
In this case, early battery replacement is recommended.
_ST60_ST60X_
Dispose of the old batteries as non-burnable rubbish, or in line with the
waste disposal regulations in your local area.
_ST60_ST60X_
1Open the cover using pen tip or screwdriver (minus -) etc.
_ST60_ST60X_
_ST60_ST60X_
2Replace the battery
_ST60_ST60X_
If difficulty, remove it with the tip of the driver.
Use the specified type of battery (coin-shaped lithium battery
CR2025).
Note the correct polarity (+ or -).
_ST60_ST60X_
_ST60_ST60X_
3Replace and fasten the cover
_ST60_ST60X_
When the battery is running low, the indicator lamp flashes 5 times on turning
the 3D Eyewear on.
In this case, early battery replacement is recommended.
When the battery is running low, the indicator lamp flashes 5 times on turning
the 3D Eyewear on.
In this case, early battery replacement is recommended.
Dispose of the old batteries as non-burnable rubbish, or in line with the
waste disposal regulations in your local area.
Dispose of the old batteries as non-burnable rubbish, or in line with the
waste disposal regulations in your local area.
1Open the cover using pen tip or screwdriver (minus -) etc.1Open the cover using pen tip or screwdriver (minus -) etc.
2Replace the battery2Replace the battery
If difficulty, remove it with the tip of the driver.
Use the specified type of battery (coin-shaped lithium battery
CR2025).
Note the correct polarity (+ or -).
If difficulty, remove it with the tip of the driver.
Use the specified type of battery (coin-shaped lithium battery
CR2025).
Note the correct polarity (+ or -).
3Replace and fasten the cover3Replace and fasten the cover
4 (0100807)

5 (0100807)

(1*/,6+
)&&67$7(0(17
7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKH
OLPLWVIRUD&ODVV%GLJLWDOGHYLFHSXUVXDQWWR3DUWRIWKH
)&&5XOHV7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOH
SURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHLQDUHVLGHQWLDO
LQVWDOODWLRQ7KLVHTXLSPHQWJHQHUDWHVXVHVDQGFDQUDGLDWH
UDGLRIUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHGDQGXVHGLQ
DFFRUGDQFHZLWKWKHLQVWUXFWLRQVPD\FDXVHKDUPIXOLQWHUIHUHQFH
WRUDGLRFRPPXQLFDWLRQV+RZHYHUWKHUHLVQRJXDUDQWHHWKDW
LQWHUIHUHQFHZLOOQRWRFFXULQDSDUWLFXODULQVWDOODWLRQ,IWKLV
HTXLSPHQWGRHVFDXVHKDUPIXOLQWHUIHUHQFHWRUDGLRRUWHOHYLVLRQ
UHFHSWLRQZKLFKFDQEHGHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRII
DQGRQWKHXVHULVHQFRXUDJHGWRWU\WRFRUUHFWWKHLQWHUIHUHQFH
E\RQHRUPRUHRIWKHIROORZLQJPHDVXUHV
 5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD
 ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
 &RQVXOWWKH3DQDVRQLF6HUYLFH&HQWHURUDQH[SHULHQFHGUDGLR
79WHFKQLFLDQIRUKHOS
FRQWLQXHGRYHUOHDI
FCC Caution:
To assure continued compliance, follow the attached
installation instructions and use only shielded USB interface
cable when connecting to computer or TV. Any changes or
modications not expressly approved by Panasonic Corp.
of North America could void the user’s authority to operate
this device.
FCC Declaration of Conformity
Models: TY-ER3D5MA
Responsible Party: Panasonic Corporation of North America
OnePanasonicWay,Secaucus,NJ07094
Contact Source: Panasonic Consumer Electronics Company
1-877-95-VIERA(958-4372)
email: [email protected]
This device complies with Part 15 of the FCC Rules. Operation is subject
tothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,
including interference that may cause undesired operation.

IC STATEMENT
Thi d i li ith I d t C d li t RSS
This device complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the
Industry Canada (IC) radio frequency exposure limits. The
Wireless Device should be used in such a manner such that the
potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with
the IC RF Exposure limits under portable exposure conditions.
(antennas are less than 20 cm of a person
'
s body)
(antennas are less than 20 cm of a person s body)
.
This device has been certified for use in Canada. Status of the
listing in the Industry
Canada’s REL (Radio Equipment List) can be found at the
following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be
found at the following web address:
found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
Cet appareil numérique de est conforme aux normes canadiennes
licence-exempt RSS standard(s)
Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas causer d'interférence et (2) cet
appareil doit accepter toute interférence, notamment les interfé
rences qui peuvent affecter son fonctionnement
rences qu
i
peuven
t
a
ff
ec
t
er son
f
onc
ti
onnemen
t
.
Informations concernant l'exposition aux fréquences radio
(RF)
La puissance de sortie émise par l’appareil de sans fil Dell est infé
rieure à la limite d'exposition aux fréquences radio d'Industry
Canada (IC). Utilisez l’appareil de sans fil Dell de façon à
minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme
aux limites d'exposition aux RF d'IC dans des conditions
d'exposition à des appareils portables. (les antennes sont moins
de 20 cm du corps d'une personne).
Ce périphérique est homologué pour l'utilisation au Canada.
Pour consulter l'entrée correspondant à l’appareil dans la liste d'é
quipement radio (REL - Radio Equipment List) d'Industry Canada
rendez-vous sur:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng
Pour des informations supplémentaires concernant l'exposition
aux RF au Canada rendez-vous sur :
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

NCCSTATEMENT

׍ᬊվ࣏⦷䴫⌒䕫ሴᙗ䴫₏㇑⨶䗖⌅

ㅜҼọ ㏃රᔿ䂽䅹Ṭѻվ࣏⦷ሴ乫䴫₏ˈ䶎㏃䁡ˈޜǃ୶㲏ᡆ֯⭘㘵൷нᗇ󰪖㠚
䆺ᴤ乫⦷ǃ࣐བྷ࣏⦷ᡆ䆺ᴤ৏䁝䀸ѻ⢩ᙗ৺࣏㜭DŽ
ㅜഋọ վ࣏⦷ሴ乫䴫₏ѻ֯⭘нᗇᖡ丯伋㡚ᆹޘ৺ᒢᬮ⌅䙊ؑ˗㏃Ⲭ⨮ᴹᒢᬮ⨮䊑ᱲˈ
៹・ণڌ⭘ˈі᭩ழ㠣❑ᒢᬮᱲᯩᗇ㒬㒼֯⭘DŽ ࡽ丵⌅䙊ؑˈᤷ׍䴫ؑ⌅㾿ᇊ֌ᾝѻ❑
㐊䴫䙊ؑDŽ վ࣏⦷ሴ乫䴫₏丸ᗽ⌅䙊ؑᡆᐕᾝǃ、ᆨ৺䟛Ⱳ⭘䴫⌒䕫ሴᙗ䴫₏䁝ۉѻ
ᒢᬮDŽ


Lens type Liquid Crystal Shutter
3D Eyewear
Dimensions(W×H×D) 165mm×42mm×171mm
Mass 27g Net
Usage temperature range 0℃-40℃
Battery* Coin-shaped lithium battery CR2025
Operation time:Approx.75 hours in continuous use of battery made by Panasonic
Viewing range* Within 3.2 m from front surface of the TV
Note
Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate
Materials Main body: Resin
Lens section: Liquid crystal glass
Communication system 2.4 GHz band FH-SS(Frequency Hopping Spread Spectrum)
*There are differences in the viewing range of the 3D Eyewear among individuals
*The 3D Eyewear may not operate correctly at the outside of the viewing range