Panasonic A35UH User manual

ACCTF32E
2017.04 industrial.panasonic.com/ac/e/
A35U
H
Stacking
Connectors for high current
Operation manual

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 1 -
Contents
01.Introduction.............................................................................................2
02.Precautions for product design...............................................................3
03.Precautions for mounting and reflow soldering.....................................15
04.Precautions for mating and unmating ...................................................25
Points which particularly need to be confirmed before designing products
are bold and underlined.

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 2 -
01. Introduction
Our Advanced series A35UH consists of ultra-small connectors with a terminal pitch of
0.35 mm, a stacking height of 0.6mm, and a shorthand width of 2.2 mm. This connector
is designed for board-to-FPC connections that require a more space-saving and high
current connector than our A35S Series.
For this purpose, the size and thickness of the molded part has been further reduced.
Select the types best suited to the conditions of use. Read this document before
designing a product and starting production.
A35UH A35S
Space-
saving Excellent
Width:
2.2mm
Very good
Width:
2.5mm
Low
profaile Excellent
Mated height
0.6mm
Very good
Mated height
0.8mm
High
current
Excellent
With
power terminal
(Max 10A at total)
Good
No
power terminal
(Max 4A at total)
Wiring
underneath
Good
Exposed metal
part on the
rear face
Exposed
metal part
Good
Exposed metal
part on the
rear face
Exposed
metal part
Contact
reliability Excellent Excellent
Drop
resistance Very good Bellows-type
contact
With a thin plastic part Very good Bellows-type
contact
With a thin plastic part
Mountability
Excellent
Header needs
special nozzle
Very good
Header needs
special nozzle
Clicking
feedback
Excellent Excellent
2.2mm
2.5mm
0.6mm
0.8mm
Header
pickup
apace:
0.8mm-
wide
bottom
Header
pickup
apace:
0.7mm-
wide
bottom
Signal terminal
0.3A/Pin
Signal terminal
0.25A/Pin
Power terminal
5A in two location

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 3 -
02. Precautions for product design
02-1. Considerations in mechanical design
1) Position of the connector on a board
Rigid boards tend to warp in a direction perpendicular to the rolling direction
during the production process. Poor soldering may occur depending on the
warping direction. Make sure to place the connector in a direction which reduces
warpage.
2) Position of the connector in the mounting process
Design multi-pin connector layouts that do not require a swinging movement
during pickup and mounting.
In many cases, deviation of the connector mounting position is caused by the
inertia of the swinging movement of the mounter. A layout that does not require
swinging is thus required.
●Example of a connector layout requiring a swinging movement in the mounting process
This space causes poor
soldering.
Pickup and mounting positions
Connector
Tends to warp in the
manufacturing (lateral) direction.
Embossed tape
Motherboard
No rotation inertia
Poor soldering can be reduced by
designing a mounting pattern to place
the connector in a lateral direction.
×
Connector
Rotary inertia is applied

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 4 -
3) Prevention of problems during use
(1)The connectors have a simple locking structure, but make sure to consider
preventive measures against the detachment of mated connectors during
practical use.
- Make sure to eliminate any gaps between the casing and board.
- We recommend that the holding force is set greater than the insertion force of
the connector.
- Select an appropriate cushioning material with a suitable shape and dimensions,
and hold down the connector at the center. (If the holding position is off the
center, it may cause detachment of mated connectors.)
(2)If the board is insufficiently fixed as in the following drawing, the inertial
load applied to the connector may damage it. Pay attention to the following
points.
Cushioning material
Casing
Sub-board
(flexible board)
Connector
Reinforcing plate
Motherboard
When an impact such as dropping as shown in the
drawing is applied:
(1) If both boards are not sufficiently fixed,
the connector will be damaged due to the
impact applied to the connector.
(2) In particular, if there is no gap between
the casing and sub-board (A<B), the sub-
board side will hit the casing wall first.
This impact may damage the connector.
<Preventive measures>
Securely fix both the motherboard and sub-board.
(1) Fixing motherboard
(Prevents inertial movement by drop impact
by fixing the side with a greater mass.)
(2) Hold down the sub-board to prevent it from
moving using a rubber cushioning material,
etc.
(3) It is safer if board gaps are set to A≥B so as
to prevent shearing damage on deviation of
the board by impact.
×
A<B
○
A
≥
B
Sub-board
(FPC)
Connector
Casing
Motherboard
(not fixed)
Connector
Casing
Motherboard
(not fixed)
Holding cushion
Sub-board (FPC)
<Preventive measures>

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 5 -
(3)To facilitate the mating of connectors, we recommend that you pay attention
to the following points when designing the motherboard.
- Provide a reference mark.
- Design a layout that allows easy-checking of the connector mating condition.
Examples of reference mark
Flexible board
Reinforcing plate
Motherboard
Provide a reference
mark:
-Silk printing
-Pattern (copper foil)

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 6 -
02-2. Precautions for board design
1) Circuit design
(1)When designing the terminal foot pattern, check the latest specifications and
examine the recommended foot pattern and dimensions of the metal mask opening.
The current recommendations are indicated on pages 13 and 14.
(2)This connector is provided with power terminal for high current.
When designing, in order to prevent an excessive temperature rise, make sure to
design a foot pattern for the power terminal.
(3)Pay attention to the following points when providing a through hole by
extending the foot pattern.
If a through-hole is created simply by extending the foot pattern by the same
width, solder is absorbed into the through-hole during the reflow process, which
may cause defective or poor soldering of the terminals.
①Thin and extend the tip of the foot
pattern before creating a through-hole.
②Prevent solder from reaching the land
by using a coverlay or resist.
Power terminal
Power terminal
Socket
Header
In general, 1/3 the
terminal pattern
width.
NG
Good
Good

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 7 -
(4)Pay attention to the following point as a pattern
peeling preventive measure when removing the
connector.
- Make the foot pattern length longer than the
coverlay opening.
In general, at least 0.3 mm.
(5)Foot pattern dimensions indicated in the drawings are
intended to achieve the minimum area on the premise
that the reflow-soldering process is used. For manual
soldering or for ensuring solder reworkability, make
a longer pattern at the terminal tip.
(6)When it is needed to provide pattern wiring and through-hole underneath the
socket, it is possible to use it by designing the pattern as shown below in case
insulation underneath the socket is not assured.
- Secure space for applying the soldering
iron tip.
Terminal looseness and unwanted
solder creep are preventable by
applying the soldering iron tip here.
Example of through hole
The area where there is a possibility
that the contacts touch.

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 8 -
(7)Resist between pins
When it is needed to provide resist between the pins, there is a way to adopt the
overresist method as below.
（If the resist is out of alignment, the pattern width 0.20mm would not change.)
Copper foil
Overresist
Resist

Operation manual for Narrow-pitch connectors A35UH
Panasonic Corporation
industrial.panasonic.com/ac/e/
©Panasonic Corporation 2017 ACCTF32E 201704
- 9 -
2) FPC board design
(1)Positions of connectors on the FPC
The FPC board is made by laminating a polyimide layer, copper foil, and adhesive
layers. Since each material has slightly different heat-shrinkable properties,
warpage may occur typically due the reflow heat in the following cases. This may
cause poor soldering. Make sure to arrange the board in a direction that minimizes
warpage.
■Example of the Assist carrier (ShinEtsu Polymer)
In case of a one-sided FPC board, warpage is
more likely to occur if a pattern is laid in a line,
or if the copper foil is applied over the entire
FPC board for noise-prevention purposes.
Since the FPC is soft, it is
difficult to keep it flat.
●Typical transfer jigs for the board
mounting process
- Magic resin (Daisho Denshi)
- Keiju board (Mitsubishi Resin)
- Assist carrier (ShinEtsu Polymer)
To keep the FPC board flat during
mounting, we recommend the use of a
“Sticky transfer jig” for the wiring board
mounting process.
Workpiece
(FPC board, etc.)
Elastomer
(Weak adhesive layer)
Elastomer
(Strong adhesive layer)
Substrate
Workpiece (FPC, etc.)
Assist carrier
Layout pin
STEP 1:
Provisional fixing of workpiece
STEP 2:
Mounting complete
STEP 3:
Removal of
workpiece
Removal pin