Panasonic CN-66A User manual

Looking for a discount?
Check out our current promotions!
This coversheet was created by Verical, a division of Arrow Electronics, Inc. (“Verical”). The attached document was created by the part supplier,
not Verical, and is provided strictly 'as is.' Verical, its subsidiaries, affiliates, employees, and agents make no representations or warranties
regarding the attached document and disclaim any liability for the consequences of relying on the information therein. All referenced brands,
product names, service names, and trademarks are the property of their respective owners.
00000005981LF-000
EOS Power
Buy Now
We have 45,000 LP502030-PCM-NTC-LD-A02554 - EEMB - Lithium Battery Rectangular 3.7V 250mAh Rechargeable in
stock now. Starting at $0.034. This EEMB part is fully warrantied and traceable.
1-855-837-4225
Give us a call
International: 1-555-555-5555 1-415-281-3866
1-415-281-3866
Arrow Electronics,
Verical Division
P.O. Box 740970
Los Angeles, CA 90074-0970
Arrow Electronics, Inc
9201 East Dry Creek Road
Centennial, CO 80112
CN-66A
PANASONIC
Buy Now

Thank you very much for purchasing Pana-
sonic products. Read this Instruction Manual
carefully and thoroughly for the correct and
optimum use of this product. Kindly keep
this manual in a convenient place for quick
reference.
CAUTIONS
2
 This product has been developed / pro-
duced for industrial use only.
 Be sure to use a crimping tool for crimp-
ing work.
 Do not reuse a contact which has been
crimped once or inserted into the hous-
ing, as its performance cannot be guar-
anteed.
 Always connect or disconnect the cable
attached connector by holding the con-
nector. Never pull the cable, since it may
cause a cable break.
OUTLINE
1
 This is a connector which can connect to
the DPC-100 series, etc.
Housing: PAP-06V-S
[manufactured by J.S.T. MFG CO., LTD]
Contact: SPHD-001T-P0.5
[manufactured by J.S.T. MFG CO., LTD]
SUITABLE CABLE
3
Note: For the cable length, refer to the Instruction Manual
of the device to which it is connected.
Conductor cross-
section area
0.12 to 0.32mm2(AWG26 to 22)
Lead wire diameter ø1.0 to ø1.5mm
Wire material Soft, twisted copper wire
Lead wire
Lead wire diameter
Conductor cross-section area
1. Use a suitable cable and prepare its end,

below.
* When processing, make sure that the core
wires are not scratched or damaged.
ASSEMBLY PROCEDURE
4
In case of cabtyre cable
Lead wire
2.1mm
Lead wire
2.1mm
(20mm) Sheath
In case of single lead wire
2. Setting the contact in the groove of the

below, insert the lead wire into the contact
and crimp.
Lead wire
Contact
<Recommended>
Crimping tool: YC-610R (AWG26 to 24)
[manufactured by J.S.T. MFG CO., LTD.]
YC-611R (AWG22)
[manufactured by J.S.T. MFG CO., LTD.]
3. After crimping, make sure to confirm that
the crimp height is appropriate.
Cable size
Sheath di-
ameter (mm)
Crimp height (mm)
Core wire Sheath (Note)
AWG26 1.3 0.6 to 0.7 1.7
AWG24 1.5 0.65 to 0.75 1.8
AWG22 1.4 0.7 to 0.8 1.8
Note: The crimp height of sheath is a reference value.
 Also, confirm that crimping is proper, as

In case the crimping is incorrect, cut the
cable and repeat the procedure from Step 1.
Lead wire
Core wire should be visible
Contact
0.3 to 0.6mm
Crimp height
Good Not good Not good
Examples of incorrect crimping
Longer protrusion of core wire Shorter protrusion of core wire
Incorrect crimping of
wire sheath
Insulation caught in
wire barrel
Uncrimped core wire strand

contact to the end of the wire inlet of the
housing.
 
the locking is proper by pulling lightly
(10N) at the cable.
The pin position differs with the type of
device connected. Connect correctly after

device to which it is connected.
Housing
Connector
CN-66A
INSTRUCTION
MANUAL
MJE-CN66A No.0036-06V
http://panasonic.net/id/pidsx/global

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: [phone] FAX: [phone]
About our sale network, please visit our website.
© Panasonic Industrial Devices SUNX Co., Ltd. 2012
PRINTED IN JAPAN