Panasonic AJ-PG50 User manual

Operating Instructions
Memory Card Portable Recorder
ModelNo.AJ-PG50
Before operating this product, please read the instructions carefully and save this manual for future use.
VQT5L34A (E)
ENGLISH
W1214TO0 -PS

2Read this first!:
indicates safety information.
WARNING:
• To reduce the risk of fire or electric shock, do not
expose this equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep
this equipment away from all liquids. Use and
store only in locations which are not exposed to
the risk of dripping or splashing liquids, and do not
place any liquid containers on top of the
equipment.
WARNING:
Always keep memory cards (optional accessory)
out of the reach of babies and small children.
CAUTION:
The mains plug of the power supply cord shall
remain readily operable.
The AC receptacle (mains socket outlet) shall be
installed near the equipment and shall be easily
accessible.
To completely disconnect this equipment from the
AC mains, disconnect the mains plug from the AC
receptacle.
CAUTION:
Danger of explosion or fire if battery is incorrectly
replaced or mistreated.
• Do not disassemble the battery or dispose of it in
fire.
• Do not store in temperatures over 60 °C (140 °F).
• Do not expose the battery to excessive heat such
as sunshine, fire or the like.
For Battery Pack
• Use specified charger.
• Replace only with same or specified type.
CAUTION:
In order to maintain adequate ventilation, do not
install or place this unit in a bookcase, built-in
cabinet or any other confined space. To prevent risk
of electric shock or fire hazard due to overheating,
ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and
annoying interference, use the recommended
accessories only.
CAUTION (For USA and Canada):
This apparatus can be operated at a voltage in the
range of 100 – 240 V AC.
Voltages other than 120 V are not intended for
U.S.A. and Canada.
Operation at a voltage other than 120 V AC may
require the use of a different AC plug. Please
contact either a local or foreign Panasonic
authorized service center for assistance in selecting
an alternate AC plug.
CAUTION:
Excessive sound pressure from earphones and
headphones can cause hearing loss.
CAUTION:
Do not leave the unit in direct contact with the skin
for long periods of time when in use.
Low temperature burn injuries may be suffered if
the high temperature parts of this unit are in direct
contact with the skin for long periods of time.
When using the equipment for long periods of time,
make use of the tripod.
CAUTION (For USA and Canada):
To prevent electric shock, match wide blade of plug
to wide slot, fully insert.
Read this first!

Read this first! (continued)
Read this first!: 3
Read this first!
indicates safety information.
FCC NOTICE (U.S.A.)
NOTIFICATION (Canada)
Declaration of Conformity
Model Number: AJ-PG50
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any unauthorized
modifications.
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user must use
only shielded interface cables when connecting to host computer or peripheral devices. Also any unauthorized changes or
modifications to this equipment could void the user’s authority to operate this device.
CAN ICES-3 (B)/NMB-3(B)
For USA
A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BAT-
TERY for information on how to recycle this battery.
Notice (U.S.A. only):
Disposal may be regulated in your community due to Environmental considerations. For disposal or recycling information,
please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.
Note:
The rating plate is on the underside of the Recorder, Battery Charger and AC Adaptor.
For Turkey
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.

Read this first! (continued)
4Read this first!:
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Декларація про Відповідність
Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин велектричному та
електронному обладнанні
(затвердженого Постановою №1057 Кабінету Міністрів України)
Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в
електричному та електронному обладнанні (ТР ОВНР).
Вміст небезпечних речовин увипадках, не обумовлених вДодатку №2 ТР ОВНР, :
1. свинець(Pb) – не перевищує 0,1 % ваги речовини або вконцентрації до 1000 частин на мільйон;
2. кадмій (Cd)– не перевищує 0,01 % ваги речовини або вконцентрації до 100 частин на мільйон;
3. ртуть(Hg) – не перевищує 0,1 % ваги речовини або вконцентрації до 1000 частин на мільйон;
4. шестивалентний хром (Cr6+ ) – не перевищує 0,1 % ваги речовини або вконцентрації до 1000 частин на мільйон;
5. полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або вконцентрації до 1000 частин на мільйон;
6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або вконцентрації до 1000 частин на
мільйон.
S3125A

Read this first! (continued)
Read this first!: 5
Read this first!
indicates safety information.
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable isnot suitable.
FOR U.K. ONLY
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K.
This appliance is supplied with a moulded three pin mains
plug for your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amps and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body
of the fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
How to replace the fuse
1. Open the fuse compartment with a screwdriver.
2. Replace the fuse
or
Fuse
Fuse
or

Read this first! (continued)
6Read this first!:
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Applicable standards and operating environment (AJ-PG50)
The apparatus is compliant with:
• standards EN55103-1 and EN55103-2, and
• electromagnetic environments E1, E2, E3 and E4
2. Pre-requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as
peripheral equipment to be connected to the apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the
apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications,
for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended
for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications,
for analog audio signals.
• Other connecting cables
Use shielded cables, which provide quality performance for high-frequency applications, such as
connecting cables for IEEE1394 or USB.
• When connecting to the HDMI signal terminal, use multilayer shielded cables, which provide quality
performance for high-frequency applications.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following
instructions in this manual.
3. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by
these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment,
such as an area where strong electromagnetic fields are generated (by the presence of signal transmission
towers, cellular phones, etc.). In order to minimize the adverse effects of the interference on the apparatus in
cases like this, it is recommended that the following steps be taken with the apparatus being affected and
with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other
appliances.
Manufactured by: Panasonic Corporation, Osaka, Japan
Importer’s name and address of pursuant to EU rules:
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany

Read this first! (continued)
Read this first!: 7
Read this first!
Batteries that may be used with this product (Correct as of March 2014)
Panasonic VW-VBD58 batteries may be used with this product.
To remove the battery
Main Power Battery
Press the battery release button.
Back-up Battery
• For the removal of the battery for disposal at the end of its service life,
please consult your dealer.
It has been found that counterfeit battery packs which look very similar to the genuine product are made available to
purchase in some markets. Some of these battery packs are not adequately protected with internal protection to meet the
requirements of appropriate safety standards. There is a possibility that these battery packs may lead to fire or explosion.
Please be advised that we are not liable for any accident or failure occurring as a result of use of a counterfeit battery pack.
To ensure that safe products are used we would recommend that a genuine Panasonic battery pack is used.
Battery Charger / AC Adaptor
Disconnect the AC mains plug from the AC mains socket when not in use.
Note regarding the Power Management function specified under COMMISSION REGULATION (EC)
No 1275/2008 implementing Directive 2009/125/EC of the European Parliament and of the Council.
This device is designed and manufactured for use at a broadcasting station and/or in a similar environment.
This device is not equipped with a Power Management function or the Power Management function is set to OFF as it will
prevent the device from fulfilling its intended purpose for the reasons below.
1. If the device is a Studio Camera, a Weather Camera, a Mixer or other processor:
A Power Management function may cause the device to suddenly stop during recording or while On Air.
2. If the device is a Studio Monitor:
A Power Management function may cause video for the confirmation of whether a signal is normal, or whether the signal
has been lost, to be un-viewable.
3. If the device is a Camera Recorder:
A professional camera recorder must be able to start quickly at any time, but a Power Management function will cause an
increase in the time taken to resume from Stand-by mode.
Battery
release button

Read this first! (continued)
8Read this first!:
This symbol in only valid in TAIWAN.
Brazil Only
Brasil Apenas
■Manuseio de baterias usadas
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa caixa destinada para
o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper a blindagem e produzir fogo.
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a garganta, danificar
o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos ter-
minais.
Não incinere nem aqueça as baterias, elas não podem ficar expostas a temperaturas superiores a 100 °C (212 °F). O gás
liberado pela bateria pode irritar a garganta,danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blind-
agem e produzir fogo devido ao curto circuito dos terminais provocado internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso
haja irritação, consulte um médico.
■Para remover a bateria
Bateria Principal de Energia
Pressione o botão para liberar a bateria. Botão de
liberação
da bateria
廢電池請回收

9
• The SDXC logo is a trademark of SD-3C, LLC.
• HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and/or other countries.
•Microsoft
®and Windows®are registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
• QuickTime and the QuickTime logo are trademarks or registered trademarks of Apple Inc., used under license therefrom.
• Apple, Mac, Mac OS, MacBook, iPhone, iPod touch, iPad, QuickTime, and Safari are registered trademarks of Apple Inc. in
the United States and/or other countries.
• Microsoft product screenshots are used in accordance with the guidelines of Microsoft Corporation.
• Other company names and product names appearing in this manual are trademarks or registered trademarks of their respec-
tive owners.
Illustrations in this manual
• Illustrations of the recorder unit and menu screens may appear different from the actual recorder unit and menu screens.
Page references
• In this manual, page references are indicated as: (➝“½½½” page ½½).
Terminology
• An SD memory card, SDHC memory card, and SDXC memory card are all referred to as an “SD memory card.”
• A memory card with the “P2” logo (for example, the separately sold AJ-P2E064FG) is referred to as a “P2 memory card.”
• A memory card with the “microP2” logo (for example, the separately sold AJ-P2M032AG) is referred to as a “microP2 memory
card.”
• A P2 memory card and microP2 memory card are referred to as a “P2 card.”
Furthermore, a P2 memory card slot and microP2 memory card slot are referred to as a “P2 card slot.”
• Recording with the system frequency at 23.98 Hz or 24 Hz is referred to as “native recording.”
• In this manual, the following operating system is referred to as “Windows 7.”
- Microsoft®Windows®7 operating system
• In this manual, the following operating system is referred to as “Windows 8.”
- Microsoft®Windows®8 operating system
• A recordable media device such as an external hard disk drive connected to a USB port is referred to as a “storage device.”
• Video created by a single recording operation is referred to as a “clip.”
• Orange button labels on the unit panel indicate alternate functions enabled by holding down the [SHIFT] button. The operating
instructions refer to the buttons only by label, without mentioning the [SHIFT] button.
Proxy recording with this product
This product is licensed under the AVC Patent Portfolio license for personal and non-commercial use, and is not licensed for
any activity except those for personal use described below.
• Recording video compliant with the AVC standard (hereinafter referred to as an AVC video).
• Playing AVC video recorded by a consumer engaged in a personal and non-commercial activity.
• Playing AVC video that was obtained from a licensed provider.
For details, refer to the MPEG LA, LLC website (http://www.mpegla.com).
Website URL
http://pro-av.panasonic.net/
About copyrights
• Copyright laws may prohibit use, except for personal pleasure, of your recorded video and audio content without permission
of the rights holder.

10
Contents
Read this first!................................................. 2
Usage Precautions ........................................ 11
Regarding this unit ............................................. 11
AC adaptor ......................................................... 12
Battery ................................................................ 13
Battery characteristics .............................................. 13
Remove the battery after use ................................... 13
Take proper care of the battery terminal .................. 13
Before Use ......................................................... 13
Setting the Area of Use (Frame Frequency and
Other Settings) .................................................... 13
Always confirm the year, month, day, time, and
time zone, and set as necessary ........................ 13
Compatible storage media ....................................... 13
Driver installation ...................................................... 14
Accessories .............................................................. 14
Optional Accessories ............................................... 14
Control Reference Guide............................... 15
Controls .............................................................. 15
Slots and I/O Controls ........................................ 17
I/O Connectors and Power Components ........... 19
Preparation .................................................... 21
Power Supply ..................................................... 21
Charging the Battery ................................................ 21
Using the Battery ................................................ 22
Installation ................................................................. 22
Removal .................................................................... 22
Using the AC Adaptor ........................................ 23
Installation ................................................................. 23
Removal ................................................................. 23
How to Turn On/Off the Power ........................... 24
Turning On the Power ............................................... 24
Turning Off the Power ............................................... 24
Auto Power Off during Operation ............................. 24
Setting the Year, Month, Day, and Time ............ 25
P2 Cards ............................................................ 26
P2 Card Access Lamp and P2 Card Status ............. 26
P2 Card Recording Times ........................................ 26
Handling of Recording Data ............................... 28
Using SD/SDHC/SDXC Memory Cards ............. 29
Available Modes ............................................ 30
Main Mode ..................................................... 31
Recording/Playback Screen ............................... 31
Recording Clips ........................................................ 31
Playing Back Clips .................................................... 34
Thumbnail Screen .............................................. 37
Displaying the Thumbnail Screen ............................. 37
Names and Functions of the Parts of the Thumbnail
Screen ................................................................ 38
Changing the Thumbnail Display ............................. 40
Playing Back Clips .................................................... 41
Selecting and Deselecting Clips .............................. 43
Adding Text Memos and Shot Marks ....................... 43
Copying Clips ........................................................... 44
Deleting Clips ........................................................... 45
Repairing and Reconnecting Clips .......................... 45
Viewing and Editing the Clip Information ................. 46
Changing Thumbnails .............................................. 47
Adding Metadata to Clips During Recording ........... 48
Formatting P2 Cards and SD Memory Cards .......... 50
Checking the Card Status ........................................ 50
Manual and Automatic CPS Authentication ............. 51
Connecting an External Device via the USB HOST
Port ..................................................................... 53
Using the Unit Connected to a Network ..............61
Network Connection ................................................. 61
Preparing for Connection ......................................... 62
Network Settings ...................................................... 63
Network Functions .................................................... 67
Network Settings ...................................................... 68
Using FTP Client Functions ...................................... 69
Viewing the Thumbnails of Clips on an FTP Server
(FTP Thumbnail Screen) ..................................... 70
Deleting Clips on the FTP Server ............................. 71
Viewing FTP Server Clip Information ........................ 71
Transferring Clips ..................................................... 71
Transferring SD Memory Card Data ......................... 73
USB Device Mode ......................................... 75
P2 Playlist Editing Mode ................................ 76
Screen Display............................................... 78
OSD Display .......................................................78
Deck Information (DIAG) Display ........................80
Waveform Monitor (WFM) Display ......................80
Time Code, User Bits, and CTL..................... 81
Time code ................................................................ 81
User Bits ................................................................... 81
CTL ........................................................................... 81
Setting the Time Code and User Bits ....................... 81
Setup Menu ................................................... 83
Menu Operations ................................................83
Menu Structure ...................................................84
Menu List ............................................................86
CLIP .......................................................................... 86
REC/PB ..................................................................... 90
I/F SETUP ................................................................. 95
FILE ........................................................................ 103
SYSTEM .................................................................. 106
List of Compatible Input and Output Formats ........ 108
Using a Keyboard ........................................ 109
Full Keyboard ......................................................... 109
Numeric Keyboard ................................................. 109
USB Keyboard ....................................................... 109
For Long and Trouble-Free Operation......... 110
Maintenance .....................................................110
Condensation ....................................................110
Storage Precautions .........................................110
Warning System ...............................................111
Warning Details ...................................................... 111
Error Codes ............................................................ 112
Updating the Firmware in This Unit ........................ 119
Specifications............................................... 120
Index ............................................................ 124

Usage Precautions: Regarding this unit 11
Usage Precautions
Usage Precautions
Regarding this unit
Panasonic makes no guarantees regarding re-
cordings
• Please note that Panasonic makes no guarantees regarding
recordings in cases where images and/or audio were not re-
corded as you intended due to problems with this unit or P2
cards.
Be careful to avoid getting water inside the unit
when using it in rainy or snowy weather, or near
the sea shore.
• The unit or a card may be damaged. (In some cases, it may
become unrepairable.)
Do not install this unit in a location exposed to
direct sunlight.
• The cabinet may be deformed and the LCD screen may be
damaged.
Keep the unit away from electromagnetic devic-
es (such as TVs and video game consoles).
• Using the unit on or near a TV may result in distorted images
or audio due to electromagnetic radiation.
• The strong magnetic field produced by loudspeakers and
large monitors may damage recordings or distort images.
• Electromagnetic waves from microcomputers may
adversely affect the unit or distort images and audio.
• If an electromagnetic device adversely affects the unit and
results in it becoming unable to be operated correctly, turn
the unit off and disconnect the AC cable from the outlet.
Then, reconnect the AC cable. Finally, turn the unit back on.
Do not use the unit near a radio transmitter or
high-voltage equipment.
• Use near a radio transmitter or high-voltage equipment may
adversely affect recorded images and audio.
When using the unit at the sea shore, in the open
air, etc., be careful not to get sand or dust in-
side.
• The sand or dust may damage the unit or a card. (Be espe-
cially careful when inserting and removing cards.)
When carrying the unit, be careful not to drop it.
• A strong impact may damage the unit and result in it be-
coming unable to be operated correctly.
Do not get insecticides or other volatile materi-
als on the unit.
• The unit may be deformed and the paint may peel off if in-
secticides or other volatile materials get on the unit.
• Do not leave the unit in contact with rubber or vinyl products
for long periods.
Notes on the disposal or transfer of memory
cards and storage devices
The format and delete functions on this unit or a computer will
only change the file management data and will leave the data
on the memory card or storage device intact. It is recommend-
ed that cards or storage devices either be physically de-
stroyed or that commercially available software be used to
completely delete any data they contain. Management of data
on memory cards and storage devices is the sole responsibil-
ity of the user.
LCD
• The pixels of the LCD monitor are controlled to obtain high
precision with 99.99% of the effective pixels. This leaves
less than 0.01% of pixels that may not light or may remain
on all the time. This is normal and will have no effect on the
images you shoot.
• There may be some unevenness on the screen depending
on the image displayed.
• Wiping or rubbing the LCD screen with a rough cloth may
damage it.
• A temporary afterimage (burn-in) may occur when the same
image or text is displayed for a long time, although it can be
recovered by turning the power off for several hours.
• LCD response and brightness vary with operating tempera-
ture.
• In a high-temperature and high-humidity location, the LCD
panel characteristics may change and result in uneven im-
age quality.
• If an unsupported signal is input to the unit for a long period
of time, the LCD panel characteristics may change and re-
sult in uneven image quality.
Notes on using the network function
Please note that Panasonic makes no guarantees regarding
damage resulting from incorrectly configuring the network
settings to use the network function. Furthermore, please also
note that Panasonic is not liable to pay compensation for any
damages arising from the use of this function.

12 Usage Precautions: AC adaptor
Notes on security
If you use the network function of this product, there is the like-
lihood of being subjected to the following damage.
• Leakage of personal information via this product
• Unauthorized operation of this product by a third party with
malicious intent
• Interference or stoppage of this product by a third party with
malicious intent
Be sure to implement sufficient security measures for comput-
ers and mobile devices.
• Set a password to limit the users who can log in.
• Use a password that is as difficult to guess as possible.
• Change the password regularly.
• Panasonic and its affiliate companies would never directly
inquire about a password. In the event that somebody does
make a direct inquiry, do not let the person know the pass-
word.
• Prior to the repair, maintenance, disposal, or transfer of this
product, initialize the network settings to prevent the leak-
age of information.
Use the supplied AC adaptor. Read the Operating Instructions (➝“Using the AC Adaptor” page 23) before use.
Information on software for this product
1. This product includes software licensed under the GNU General Public License (GPL) and GNU Lesser General Public Li-
cense (LGPL), and users are hereby informed that they have the right to obtain, modify, and redistribute the source code
of this software.
2. This product includes software licensed under the MIT-License.
3. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/).
4. This product includes software licensed under the OpenBSD License.
5. This product includes PHP, freely available from <http://www.php.net/>.
6. This software is based in part on the work of the Independent JPEG Group.
7. This product includes software licensed under the MOZILLA PUBLIC LICENSE.
To see the details (in the original (English-language) text) and obtain the source code, visit the following website. (➝“Web-
site URL” on page 9)
Users are requested to refrain from making any inquiries about the source code they have obtained.
AC adaptor

Usage Precautions: Battery 13
Usage Precautions
Battery
This unit uses a rechargeable lithium-ion battery that uses its internal chemical reaction to generate electrical energy. This re-
action is easily influenced by the ambient temperature and humidity, and the battery’s effective operating time is reduced as
the temperature rises or falls. In very low temperatures, the battery may last only 5 minutes.
Protective circuitry functions if you use the battery where it is very hot and you will have to wait before you can use it again.
Completely remove the battery. (The battery continues to be used even if you have turned the unit off.)
The battery can over discharge if you leave it in the unit and it may become impossible to recharge it.
Do not allow dust or foreign objects on the battery terminal.
Also, if you drop the battery by mistake, make sure that the battery body and the terminal are not warped.
Inserting a deformed battery into the unit or attaching it to the battery charger may cause damages on the unit or battery char-
ger.
This unit is shipped with the area of use unset. Before using the unit for the first time, refer to the included leaflet.
The clock setting affects the management of recorded content and playback order. Before recording, set and confirm the year,
month, day, time, and time zone settings.
If the unit is left without an electric power supply for a long period of time (approximately 3 months), "BACKUP BATT EMPTY"
may be displayed when the power is turned on. If that happens, set the date and time information because it has been initialized.
(➝“Setting the Year, Month, Day, and Time” page 25)
Also charge the backup battery. (➝“BACKUP BATT EMPTY” page 113)
The following types of storage media can be used. See the specified pages for details.
Recording and playback
• P2 memory cards and microP2 memory cards (➝“P2 Cards” page 26)
Proxy recording and data storage
• SD, SDHC, and SDXC memory cards (➝“Using SD/SDHC/SDXC Memory Cards” page 29)
Battery characteristics
Remove the battery after use
Take proper care of the battery terminal
Before Use
Setting the Area of Use (Frame Frequency and Other Settings)
Always confirm the year, month, day, time, and time zone, and set as necessary
Compatible storage media

14 Usage Precautions: Before Use
Before use, download the necessary drivers from the Panasonic website and install them on the personal computer.
For the installation procedure, refer to installation manual on the Panasonic website.
For details on the supplied accessories, refer to the included leaflet.
• Battery VW-VBD55 (7.2 V/5400 mAh)
• Battery VW-VBD58 (7.2 V/5800 mAh, product equivalent to the supplied battery)
Driver installation
For the latest information on drivers, refer to the Panasonic website. Refer to (➝“Website URL” page 9)
Accessories
Optional Accessories

Control Reference Guide: Controls 15
Control Reference Guide
Control Reference Guide
Controls
About button labels: Orange labels indicate alternate functions enabled by simultaneously pressing the [SHIFT] button.
<Example> Press the [SHIFT] and [DISPLAY/MODE] buttons simultaneously to execute the [MODE] button function.
1. DISPLAY, MODE button
[DISPLAY] button:
This button toggles display of the OSD on and off.
(➝“Screen Display” page 78)
[MODE] button:
This button switches between USB device mode (USB DE-
VICE) and PLAYLIST editing mode.
(➝“USB Device Mode” page 75, “P2 Playlist Editing
Mode” page 76)
2. COUNTER button
This button switches the counter display in the following
order.
TC➝UB➝CTL➝TC
(➝“Time Code, User Bits, and CTL” page 81)
3. (Power) button
This button turns the power on or off.
(➝“How to Turn On/Off the Power” page 24)
4. (Power) lamp
This button displays the operating status of the unit.
(➝“How to Turn On/Off the Power” page 24)
When an error is detected after the power is turned on or
during operation, the (POWER) lamp and a beep
sound notify you that an error has occurred. (➝“Warning
Details” page 111)
5. RESET button
When the counter display on the display panel is CTL,
press this button to reset the counter display to
“0:00:00:00”.
(➝“Time Code, User Bits, and CTL” page 81)
6. AUDIO LEVEL buttons
[AUDIO LEVEL-REC] button:
This button displays the recording audio level adjustment
screen.
(➝“Recording Clips” page 31)
[AUDIO LEVEL-PB] button:
This button displays the playback audio level adjustment
screen.
(➝“Playing Back Clips” page 34)
1
10
14
11
15 16 17 18 19 20
13
1
2
2
3
4
5
7
9
6
8

16 Control Reference Guide: Controls
7. TC PRESET button
This button sets the TC or UB value.
(➝“Time Code, User Bits, and CTL” page 81)
8. (Monitor volume adjustment) buttons
Monitor audio volume adjustment:
Press either the + or -, button to display the loud-
speaker/headphone audio volume level, and hold the but-
ton to adjust. Wait a short time or press [SET] or [EXIT] to
return the display to normal.
9. USER 1-3, 4-6 buttons
Users can assign any functions to these buttons.
(➝“USER BUTTON” page 102)
10.THUMBNAIL button
This button displays or hides the thumbnail screen.
(➝“Displaying the Thumbnail Screen” page 37)
11.SHIFT button
Hold this button while pressing another button to perform
the assigned function of that button.
12.Cursor control buttons
Up/down/left/right cursor buttons:
• These buttons control the cursor movement for thumb-
nails, menus, etc.
• During playback, press the Left/Right cursor buttons to
activate SHTL mode to change playback speed.
(➝“Variable speed playback” page 34)
• Press the [SET] button to pause variable speed play-
back.
• Press the up or down cursor button during the display of
playback still images to step one frame forward or back.
(➝“Frame-by-frame playback” page 35)
• Use the left or right cursor button to switch the audio
channel for recording and playback audio level adjust-
ment.
(➝“Recording Clips” page 31)
[TOP]/[BOTTOM] buttons:
These buttons move the cursor to the first (TOP) or last
(BOTTOM) thumbnail.
[SET] button:
This button allows you to perform operations such as se-
lecting thumbnails and menu items.
13.MENU, DIAG button
[MENU] button:
This button displays the menu.
[DIAG] button:
When the menu is not displayed, press this button to dis-
play the DIAG screen for viewing various conditions.
(➝“Deck Information (DIAG) Display” page 80)
14.EXIT, CANCEL button
[EXIT] button:
This button closes the menu or returns from the storage ex-
plorer to normal display.
[CANCEL] button:
This button cancels a selection, stops copying, etc.
15.REW, PREV button
[REW] button:
This button fast rewinds playback.
The speed can be selected in the “FF.REW MAX” (➝page
91) menu item.
[PREV] button:
This button cues the current or previous clip or the clip and
text memo location during playback.
16.STOP button
This button stops playback or recording.
17.FF, NEXT button
[FF] button:
This button fast forwards playback.
The speed can be selected in the “FF.REW MAX” (➝page
91) menu item.
[NEXT] button:
This button cues the next clip or the clip and text memo lo-
cation during playback.
18.PLAY button
This button starts playback.
(➝“Playing Back Clips” page 34)
19.PAUSE button
Press this button during playback to pause (STILL) play-
back to display a still image.
Press the button while playback is paused to resume play-
back.
Press the button during recording to switch to the record-
ing standby (PAUSE) state.
Press the button in the recording standby state to resume
recording.
20.REC button
This button allows you to check EE video and audio during
playback image output. EE will continue while the button is
being pressed.
EE mode monitoring is only available when the playback
video format matches the setting in the “LINE&FREQ” (➝
page 106) menu item. It will not function if recordable me-
dia does not exist.
Press this button and the [PLAY] button simultaneous-
ly to start recording.
Press this button and the [PAUSE] button simultane-
ously to switch to the recording standby state. Remote re-
cording from a camera can be enabled from the menu.
Set remote recording in the “AUTO REC” (➝page 90)
menu item.

Control Reference Guide: Slots and I/O Controls 17
Control Reference Guide
Slots and I/O Controls
1. microP2 memory card slots
(➝“P2 Cards” page 26)
2. microP2 memory card access lamps
(➝“P2 Card Access Lamp and P2 Card Status” page 26)
3. EJECT button
(➝“P2 Cards” page 26)
4. P2 memory card slot
(➝“P2 Cards” page 26)
5. P2 memory card access lamp
(➝“P2 Card Access Lamp and P2 Card Status” page 26)
6. Speaker
This speaker outputs the monitor audio.
Output from the speaker is disabled when headphones
are connected.
6
5
3
4
2
1

18 Control Reference Guide: Slots and I/O Controls
1. SD/SDHC/SDXC memory card slot and access lamp
Insert an SD/SDHC/SDXC memory card.
Insert the cut-corner-edge first with the label-side up, until
the card latches into place.
When removing a card, check that the access lamp is not
lit green, then release the latch by gently pushing the card
in again.
Note:
Use SD/SDHC/SDXC memory cards for reading the CPS pass-
word, reading and writing menu settings, reading and writing
metadata, and proxy recording.
(➝“Using SD/SDHC/SDXC Memory Cards” page 29)
2. HDMI OUT connector
Connect a monitor or TV using an HDMI cable.
Note:
• This unit does not support Viera Link. Be aware that con-
necting a Viera Link compatible device using an HDMI cable
may cause Viera Link to malfunction on the other device.
• Use a double-shielded cable to connect to this port.
• When “VIDEO” - “INPUT SEL” is set to “HDMI”, video, audio,
and other signals from the HDMI output connector will not be
output. In addition, the thumbnail screen will not be output.
3. HDMI IN connector
Use an HDMI cable to connect a camera recorder, etc.
here.
Note:
• This unit does not support Viera Link. Be aware that con-
necting a Viera Link compatible device using an HDMI cable
may cause Viera Link to malfunction on the other device.
• Use a double-shielded cable to connect to this port.
• When HDCP signals are detected, external output is
stopped and recording will not be possible. In addition, the
thumbnail screen will not be output.
• This unit does not support 60 Hz JUST frequency signals.
For the input signals, use 59.94 Hz or 50 Hz signals. Even
when using 59.94 Hz or 50 Hz signals, if there is a discrep-
ancy in the frequency, reception will not be possible (in the
case of some computers, for example).
• When an input signal cannot be received, the “INVALID
INPUT FORMAT”warning will be displayed and the video
will be black and muted.
4. USB 3.0 HOST port (USB 3.0 Type A)
(➝“Connecting an External Device via the USB HOST
Port” page 53)
Note:
• Use a double-shielded cable to connect to this port.
• Use a USB 3.0 compliant cable to connect USB 3.0 compat-
ible storage devices.
• When using this unit with the battery, externally supply pow-
er to any storage device connected to the [USB3.0 HOST]
port.
5. USB 2.0 device port
(➝“USB Device Mode” page 75)
Note:
Use a double-shielded cable to connect to this port.
6. LAN port
This port enables a 100BASE-TX/10BASE-T network con-
nection.
(➝“Using the Unit Connected to a Network” page 61)
Note:
• Use a shielded cable to connect to this port.
• The orange lamp lights when a LAN link is established. The
green lamp flashes while data is being transferred.
7. AUDIO OUT connector
Outputs the audio signals (CH1 to CH4) selected in the
“MONITOR CH” (➝page 97) menu item.
8. PHONES (Headphone) jack
Headphone jack:
This jack is for connecting stereo headphones to listen to
the sound being recorded or played back with the head-
phones.
8
1
3 2
4 5 76

Control Reference Guide: I/O Connectors and Power Components 19
Control Reference Guide
I/O Connectors and Power Components
1. ANALOG AUDIO IN jacks
These jacks are for inputting analog audio.
2. HD/SD-SDI IN/OUT jacks
These jacks are for inputting and outputting serial digital
component audio/video signals.
The output jack for superimposition can be changed in the
“OSD OUTPUT” (➝page 100) menu setting, and the out-
put jack for thumbnail screen superimposition can be
changed in the “GUI OUTPUT” menu setting (➝page
100).
Note:
Use 5C-FB or equivalent double-shielded cables to connect
to these jacks.
3. TIME CODE IN Jacks
This jack is for recording an external time code onto a P2
card.
4. Battery lock release button
(➝“Using the Battery” page 22)
5. Battery attachment point
(➝“Using the Battery” page 22)
5
4
3
1
2

20 Control Reference Guide: I/O Connectors and Power Components
1. Fan
This fan is for cooling the unit. Install the unit where the
ventilation holes will not be blocked.
Note:
If the fan is stopped while the power is on, the “FAN
STOPPED” (➝page 113) warning is displayed. Stop opera-
tion and turn off the unit immediately, and contact your dealer.
2. DC IN connector
Connect a 12 V DC power supply.
When the voltage drops to approximately 10.0 V, the unit
is shutdown automatically.
Afterwards, the power is not restored automatically even if
the power supply voltage recovers. Press and hold the
[ ] button for at least 1 second to turn the power on.
Note:
When using an external DC power supply, be sure to check
the external DC power supply ratings and use one that is suit-
able for the unit.
Check the pin assignment of the DC output connector of the
external DC power supply and the DC IN connector on the
unit, and connect the connectors with the correct polarity. In-
correct connection of the +12 V power supply to the GND
connector may cause a fire or injury.
2
1