Panasonic UB-5325 User manual

Electronic Board
Installation Manual
(for qualified service personnel)
Model No. UB-5325
UB-5825
English . . . . . . . . . . . . . . . . . 1- 22
Français . . . . . . . . . . . . . . . . 23- 44
Deutsch . . . . . . . . . . . . . . . . 45- 66
Español . . . . . . . . . . . . . . . . 67- 88
Italiano . . . . . . . . . . . . . . . . . 89-110
Nederlands. . . . . . . . . . . . . .111-132
Svenska . . . . . . . . . . . . . . . .133-154
中 文 . . . . . . . . . . . . . . . . . .155-176
Русский . . . . . . . . . . . . . . . .177-198
The unit in this picture is UB-5325.
(Stand and Wall-mounting kit are optional.)
[Stand (option)] [Wall-mounting (option)]
English
Français
Deutsch
Español
Italiano
Nederlands
Svenska
中 文
Русский
• Please ask your dealer regarding assembly of the electronic board and instruction for wall-mounting.
Before installing this set, please read this manual completely.
Cover_EN.fm 1 ページ ２００９年１月９日 金曜日 午後６時０分

2
Before installing this set, please read this manual completely.
CLASS 1 LED PRODUCT
WARNING
Have the unit installed, removed and disposed of only by qualified
service personnel.
Safety check must be done by qualified service personnel after
installing this option.
Table of Contents
page
Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . . . . 3
●Accessories for assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electronic Board Operations Check. . . . . . . . . . . . . . . . . . . . . 13
Repacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assembling the Optional Stand (KX-B061) . . . . . . . . . . . . . . . 15
●Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Optional Wall-mounting Kit (KX-B063). . . . . . . . . . . . . . . . . . . 19
●Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
●Wall-mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
●Attaching the wall-mounting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . 21
UB-5325_IM_EN.book 2 ページ ２００８年１月８日 火曜日 午後５時７分

3
English
Assembling the Electronic Board
■Accessories for assembling
The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts
are included in the package before proceeding.
No. Part Name
Illustration / Quantity
Remarks
UB-5325 / UB-5825 Q’ty
Screen fastening
bracket
2
Upper frame cover
(with two rivets)
1
Lower frame cover
1
Hexagonal screws
10
Wing bolts
2
Power cord
1
Wrench
1For hexagonal
screws ( )
Wall-mounting
template
1For wall-mounting
UB-5325_IM_EN.book 3 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
4
■Assembly
1Assemble the optional stand or wall-mounting kit.
■If you are using a stand, refer to page 15.
■If you are using a wall-mounting kit, refer to page 19.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
• When removing the screen unit, grasp the metal frames on both sides of the screen.
Do not grasp the screen film surface, as this may scratch it.
• The shipping box, cushioning material, and other packing material will be necessary if you ever need to
repackage the electronic board, so do not throw them away.
Manuals, CD-ROM
Markers
Eraser
Thermal transfer film
Power cord
Lower frame cover
Upper frame cover
Screen fastening brackets
Wrench
Hexagonal screws
Wing bolts
Scanner / printer unit
Screen unit
Joints
Joints
[UB-5325]
Shipping box
Shipping box
Caution
UB-5325_IM_EN.book 4 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
5
English
• When removing the screen unit, grasp the metal frames on both sides of the screen.
Do not grasp the screen film surface, as this may scratch it.
• The shipping box, cushioning material, and other packing material will be necessary if you ever need to
repackage the electronic board, so do not throw them away.
Thermal transfer film
Power cord
Joints
Joints
Eraser
Markers
Manuals,
CD-ROM
Upper frame cover
Lower frame cover
Screen fastening
brackets
Wing bolts
Wrench
Hexagonal screws
Scanner /printer
unit
Screen unit
[UB-5825]
Shipping box
Shipping box
Caution
UB-5325_IM_EN.book 5 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
6
3Collapse the shipping box.
Remove the tape on the unopened side of the
shipping box, then collapse the box.
4Remove the protective plastic bags.
After removing the protective plastic bags from
the screen unit and scanner / printer unit, set
those units on top of the collapsed shipping
box.
• Do not touch the screen film surface as doing so
may damage it.
5Attach the scanner / printer unit to
the optional stand or wall-mounting
kit.
■If you are using the stand (option):
1) Hang the scanner / printer unit on the stand
fixtures using the wing bolts Aor B.
• The electronic board can be mounted
200 mm (7 7/8”) higher than hang position A
by hanging it with the wing bolts B.
2) Install the scanner / printer unit with the two
wing bolts included in the stand (option).
Remove the tape.
Protective plastic
bag
Screen film
surface
Set the unit so that
the gear side is on
the bottom.
Caution
Scanner /
printer unit
A
B
UB-5325_IM_EN.book 6 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
7
English
■If you are using the wall-mounting
kit (option):
1) Hang the scanner / printer unit on the wall-
mounting fixtures using the wing bolts
A or B ( ➊ ).
2) Screw the two wing bolts [included in the wall-
mounting kit (option)] into the lower side
wall-mounting fixtures (➋).
• The electronic board can be mounted
200 mm (7 7/8”) higher than hang position A
by hanging it with the wing bolts B.
6Remove the fastening belt
( ➊ ),
cushions (➋) and tapes (➌).
7Insert the two supplied screen
fastening brackets into the screen
unit frame.
8Open the screen film surface.
• When opening the screen film surface, be
careful not to scratch or wrinkle it.
2
2
1
1
A
B
Wall mounting fixture L
Wall
mounting
fixture R
Screen unit
Fastening
belt
Pull here to
remove the
fastening
belt.
Pull
Pull
Fastening belt
(required for
repacking)
2
2
1
1
3
3
Tape
Projection
Screen fastening
bracket
Screen fastening
bracket
Screen film surface Roller
Caution
UB-5325_IM_EN.book 7 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
8
9Fasten the brackets.
1) Move the screen fastening brackets toward the
center and fasten them with the four
hexagonal screws provided.
2) Fasten the screen fastening brackets in the
front of the screen with two hexagonal screws
provided.
10 Attach the screen unit to the
scanner / printer unit.
1) Set the two provided hexagonal screws to the
scanner / printer unit. (Be sure to leave about
5 mm (1/2”) space to hang the screen unit.)
2) Hang the screen unit on the scanner / printer
unit, fitting the screen mounting guide through
the hole of the screen unit.
Screen fastening
bracket
Hexagonal screws
Rear view
Hexagonal
screws
Front view
Hexagonal
screws
5 mm
(1/2
" )
Screen mounting guide
UB-5325_IM_EN.book 8 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
9
English
3) Fasten the two screws (➊), then secure the
screen unit with the two provided hexagonal
screws (➋).
4) Loosen the hexagonal screw (➊) and move
the gear fixing bracket in the direction of the
arrow (➋). [The gear (A) will be raised.]
5) Fasten the hexagonal screw (➋) while
pressing the gear fixing bracket in the
direction of the arrow (➊).
11 Remove the tape fastening the
screen film surface.
2
2
1
1
Hexagonal
screws
A
2
1
Hexagonal
screw
Gear fixing bracket
2
1
Hexagonal screw
Gear fixing bracket
UB-5325_IM_EN.book 9 ページ ２００８年１月８日 火曜日 午後５時７分

Assembling the Electronic Board
10
12 Remove the roller and paper.
Bend and remove the roller (➊), then remove
the paper with tape (➋). (The roller and paper
are needed for repacking.)
13 Attach the upper frame cover.
1) Align the upper frame cover with the metal
fittings on the left and right ends, then rotate it
in the direction of the arrows.
2) Be sure the back of the frame cover (A) is fit to
the frame of the screen unit and push down
the two rivets.
3) Place the wrench in the wrench holder.
1
2
2
Metal fitting
A
Wrench
UB-5325_IM_EN.book 10 ページ ２００８年１月８日 火曜日 午後５時７分