Panasonic 10GBASE-SR SFP+ User manual

PN59021-TH/PN59023-TH
PN59021-MY/PN59023-MY
PN59021-ID/PN59023-ID
PN59021-SG/PN59023-SG
PN59021-NZ/PN59023-NZ
Model No.
10GBASE-LR SFP+ Module (SFP+10GLR)
10GBASE-SR SFP+ Module 10GBASE-LR SFP+ Module
PN59021 PN59023
IEEE802.3ae
10GBASE-SR
IEEE802.3ae
10GBASE-LR
SFF-8472 (Diagnostic Monitoring Interface)
850 nm 1310 nm
DC 3.3 V
0 to 50°C /20 to 80% RH (No dew condensation)
10GBASE-SR SFP+ Module (SFP+10GSR)
Installation Guide
 Thank you for purchasing our product.
 This document provides important information about safe and proper
operations of this SFP+ Module.
 Please read the "Important Safety Instructions".
 Any problems or damages resulting from disassembly
of this SFP+ Module by customers are not covered by
the warranty.
 The instruction guide can be downloaded from the
following URL.
https://panasonic.co.jp/ew/pewnw/english/datadownload/index.html
C1214-20122 Printed in Japan
Product Outline
Specifications
Product name
Module No.
Standards
Compatible cable
Optical wavelength
Operating voltage
Power consumption
Operating ambient
temperature/humidity
Fiber optic port
connector type
Accessories
MMF cable
LC connector (Duplex)
SMF cable
1.0 W max 1.25 W max
External dimensions
Mass (Weight) 17 g
9 mm (Height) x 14 mm (Width) x 57 mm (Depth)
(Excluding protruding sections)
Installation Guide (this document) x 1(*)
＊Just the PN59021-TH/PN59023-TH has 1 Installation Guide in
Thai (at total of 2 guides)
Prot ection cap of the fiber optic port (Attached to the module)
x 1
10GBASE-SR SFP+ Module and 10GBASE-LR SFP+ Module are SFP (Small Form-Factor
Pluggable) modules to be connected to a Panasonic Ethernet Switch’s SFP+ extension
slot.
MMF: Multi Mode Fiber SMF: Single Mode Fiber
1. Securely connect the SFP+ Module to the
SFP+ extension slot of a Panasonic Ethernet
Switch.
2. Remove the protective cap of the SFP+
Module’s fiber optic port.
3. Connect a fiber optic cable that meets the
standards specified for the SFP+ Module.
4. Connect another SFP+ Module of the same
model number on the opposite end.
1. Unlatch the fiber optic cable and remove it from the
SFP+ Module.
2. Pull down the lever of the SFP+ Module 90 degrees as
shown in the figure to unlatch the SFP+ Module.
3. Pull out the SFP+ Module.
Installation
Removal
SFP+ extension slot
SFP+ Module
Fiber optic port Ethernet Switch
Lever
2-12-7, Higashi-Shimbashi, Minato-ku, Tokyo Japan, 105-0021
©
2-12-7, Higashi-Shimbashi, Minato-ku, Tokyo Japan, 105-0021
©
Panasonic Electric Works Networks Co.,Ltd.
Panasonic Electric Works Networks Co.,Ltd. 2022

This chapter contains important safety instructions for preventing bodily injury
and/or property damage. Please read carefully, and follow them at all times.
Do not look at the laser light.
Deviation could lead to visual impairment. (Class 1 Laser Product)
Do not disassemble and/or modify this SFP+ Module.
Deviation could lead to fire, electric shock, and/or equipment failure.
 Severity of bodily injury and/or property damage, which could result from incorrect
use of the SFP+ Module, are explained below.
 The following symbols are used to classify and describe the type of instructions to be
observed.
Important Safety Instructions
This symbol indicates safety instructions.
Deviation from these instructions could lead to
bodily injury and/or property damage.
CAUTION
This symbol indicates a potential hazard
that could result in serious injury or death.
WARNING
This symbol is used to alert
users what they must do.
This symbol is used to alert
users what they must not do.
WARNING
CAUTION
Basic Instructions for the Use of This Product
Handle the SFP+ Module carefully so that fingers or hands may not be
injured by its end connected to the Ethernet Switch or the SFP+
extension slot of the Ethernet Switch.
For inspection and/or repair, consult the retailer.
Correctly and securely connect the SFP+ Module to the SFP+ extension slot
of a Panasonic Ethernet Switch.
Check the connector of the fiber optic cable for dirt and dust. If it is dirty,
be sure to clean it before connecting it to the fiber optic port.
Remove the SFP+ Module from the SFP+ extension slot before cleaning the
SFP+ Module.
Do not touch the metal terminal or place electrically-charged objects in the
proximity of the SFP+ Module. Static electricity could lead to breakdown.
Please use the SFP+ Module in locations where the ambient temperature is
within the range of 0 to 50°C.
Do not use the SFP+ Module in any condition where the specification limits
are exceeded.
Deviation could lead to malfunctions.
1. Panasonic will not be liable for any damage resulting from the operation not in
accordance with this document or the loss of communications, which may or
may not be caused by failure and/or malfunction of this product.
2. The contents described in this document may be changed without prior notice.
3. For any question, please contact the retailer where you purchased the product.
 The port LED of the Ethernet Switch to which the SFP+ Module connected is not lit.
Is the Ethernet Switch powered on?
Is the SFP+ Module securely connected to the target SFP+ extension slot of the
Ethernet Switch?
Is the connected port of the Ethernet Switch enabled?
Is the cable correctly connected to the target port?
Is a conforming cable used? Is the same type of SFP+ Module used on the
opposite end?
Is the equipment connected to the target port compliant with the specified
standards?
Ensure that 100BASE-FX or 1000BASE-X equipment is not connected.
Troubleshooting
If you find any problem, please take the following steps to check.