Panasonic SFP-1000SX User manual

2-12-7, Higashi-Shimbashi, Minato-ku, Tokyo Japan, 105-0021
©
Panasonic Electric Works Networks Co.,Ltd.
Panasonic Electric Works Networks Co.,Ltd. 2022
Product Outline
1000BASE-SX SFP Module and 1000BASE-LX SFP Module are SFP (Small Form-Factor
Pluggable) modules to be connected to a Panasonic Ethernet Switch’s SFP extension slot.
1000BASE-SX SFP Module 1000BASE-LX SFP Module
PN54021K PN54023K
IEEE802.3z
1000BASE-SX
IEEE802.3z
1000BASE-LX
SFF-8472 (Diagnostic Monitoring Interface)
850 nm 1310 nm
DC 3.3 V
0 to 50°C /20 to 80% RH (No dew condensation)
Specifications
Product name
Standards
Compatible cable
Optical wavelength
Operating voltage
Power consumption
Operating ambient
temperature/humidity
Fiber optic port
connector type
Accessories
MMF cable
LC connector (Duplex)
SMF, MMF cable
0.7 W max 0.9 W max
External dimensions
Mass (Weight) 17 g
9 mm (Height) x 14 mm (Width) x 57 mm (Depth)
(Excluding protruding sections)
Installation Guide (this document) x 1(*)
＊Just the PN54021K-TH/PN54023K-TH has 1 Installation
Guide in Thai (at total of 2 guides)
Protection cap of the fiber optic port (Attached to the module) x 1
Module No.
MMF: Multi Mode Fiber SMF: Single Mode Fiber
1. Securely connect the SFP Module to the SFP
extension slot of a Panasonic Ethernet Switch.
2. Remove the protective cap of the SFP
Module’s fiber optic port.
3. Connect a fiber optic cable that meets the
standards specified for the SFP Module.
4. Connect another SFP Module of the same
model number on the opposite end.
Installation
SFP extension slot
SFP Module
Fiber optic port Ethernet Switch
1. Unlatch the fiber optic cable and remove it from the SFP
Module.
2. Pull down the lever of the SFP Module 90 degrees as
shown in the figure to unlatch the SFP Module.
3. Pull out the SFP Module.
Removal
Lever C0913-20122 Printed in Japan
 Thank you for purchasing our product.
 This document provides important information about safe and proper
operations of this SFP Module.
 Please read the "Important Safety Instructions".
 Any problems or damages resulting from disassembly
of this SFP Module by customers are not covered by
the warranty.
 The instruction guide can be downloaded from the
following URL.
https://panasonic.co.jp/ew/pewnw/english/datadownload/index.html
PN54021K-TH/PN54023K-TH
PN54021K-MY/PN54023K-MY
PN54021Ｋ-ID/PN54023Ｋ-ID
PN54021K-SG/PN54023K-SG
PN54021K-NZ/PN54023K-NZ
Model No.
1000BASE-LX SFP Module (SFP-1000LX)
1000BASE-SX SFP Module (SFP-1000SX)
Installation Guide

This chapter contains important safety instructions for preventing bodily injury
and/or property damage. Please read carefully, and follow them at all times.
Do not look at the laser light.
Deviation could lead to visual impairment. (Class 1 Laser Product)
Do not disassemble and/or modify this SFP Module.
Deviation could lead to fire, electric shock, and/or equipment failure.
 Severity of bodily injury and/or property damage, which could result from incorrect
use of the SFP Module, are explained below.
 The following symbols are used to classify and describe the type of instructions to be
observed.
Important Safety Instructions
This symbol indicates safety instructions.
Deviation from these instructions could lead to
bodily injury and/or property damage.
CAUTION
This symbol indicates a potential hazard
that could result in serious injury or death.
WARNING
This symbol is used to alert
users what they must do.
This symbol is used to alert
users what they must not do.
WARNING
CAUTION
Handle the SFP Module carefully so that fingers or hands may not be
injured by its end connected to the Ethernet Switch or the SFP
extension slot of the Ethernet Switch.
Basic Instructions for the Use of This Product
For inspection and/or repair, consult the retailer.
Correctly and securely connect the SFP Module to the SFP extension slot of
a Panasonic Ethernet Switch.
Check the connector of the fiber optic cable for dirt and dust. If it is dirty,
be sure to clean it before connecting it to the fiber optic port.
Remove the SFP Module from the SFP extension slot before cleaning the
SFP Module.
Do not touch the metal terminal or place electrically-charged objects in the
proximity of the SFP Module. Static electricity could lead to breakdown.
Please use the SFP Module in locations where the ambient temperature is
within the range of 0 to 50°C.
Do not use the SFP Module in any condition where the specification limits
are exceeded.
Deviation could lead to malfunctions.
1. Panasonic will not be liable for any damage resulting from the operation not in
accordance with this document or the loss of communications, which may or
may not be caused by failure and/or malfunction of this product.
2. The contents described in this document may be changed without prior notice.
3. For any question, please contact the retailer where you purchased the product.
 The port LED of the Ethernet Switch to which the SFP Module connected is not lit.
Is the Ethernet Switch powered on?
Is the SFP Module securely connected to the target SFP extension slot of the
Ethernet Switch?
Is the connected port of the Ethernet Switch enabled?
Is the cable correctly connected to the target port?
Is a conforming cable used? Is the same type of SFP Module used on the
opposite end?
Is the equipment connected to the target port compliant with the specified
standards?
Ensure that 100BASE-FX or 10GBASE equipment is not connected.
Troubleshooting
If you find any problem, please take the following steps to check.