Panasonic FV-0511VQL1 User manual

INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before attempting to install, operate or service
the Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION”
Failure to comply with instructions could result in personal injury or property damage.
Please explain to users how to operate and maintain the product after installation,
and this booklet should be presented to users.
Please retain this booklet for future reference.
Representative models:
FV-0511VQL1
FV-1115VQL1
FV-0511VQCL1
Ventilating Fan
FV-1115VQL1
FV-0511VQCL1
Model No.
FV-0511VQL1
Contents
GENERAL SAFETY INFORMATION
DESCRIPTION
UNPACKING
SUPPLIED ACCESSORIES
DIMENSIONS
WIRING DIAGRAM
SELECTOR INDICATION (FV-0511VQCL1 only)
OPERATION (FV-0511VQCL1 only)
FEATURE
INSTALLATION (NEW CONSTRUCTION)
INSTALLATION (RETROFIT)
MAINTENANCE (CLEANING)
PRACTICAL GUIDE TO INSTALLATION
SPECIFICATIONS
PRODUCT SERVICE
--------------2~3
----------------------------------------4
-----------------------------------------4
--------------------------4
-----------------------------------------5
-----------------------------------6
---------6
-----------------7
---------------------------------------------7
--------8~9
-----------------------10
------------------10~11
-----------11
-----------------------
------------ 11
-------------------- BACK COVER
1 1 Q C L 1 4 2 0 B

English
To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to
equipment or property, always observe the following safety precautions.
Denotes a potential hazard that could result in serious
injury or death.
Denotes a hazard that could result in minor injury.
The following symbols are used to classify and describe the type of instructions to be observed.
This symbol is used to alert users to a specific operating procedure that must not be
performed.
This symbol is used to alert users to a specific operating procedure that must be followed
in order to operate the unit safely.
WARNING
WARNING
The following symbol word panels are used to classify and describe the level of hazard, injury, and
property damage caused when the denotation is disregarded and improper use is performed.
CAUTION
This symbol is used to alert users not to disassemble the equipment.
This symbol is used to alert users to make sure of grounding when using the equipment
with the grounding terminal.
GENERAL SAFETY INFORMATION
Denotes a hazard that could result in property damage.
To reduce the risk of fire, electric shock or injury to persons, observe the following :
Use this unit only in the manner intended by the manufacturer. If you have any questions,
contact the manufacturer.
Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Installation work and electrical wiring must be done by qualified person(s) in accordance with
all applicable codes and standards, including fire-rated construction.
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
Ducted fans must always be vented to the outdoors.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the
application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch
circuit.
These models are UL listed for tub and shower enclosures.
2
NOTICE
For Your Safety
Explanation of symbol word panels

English
GENERAL SAFETY INFORMATION CONTINUED
CAUTION
Make sure that the electric service supply voltage is AC 120V, 60Hz.
Canada only: Not to be installed in a ceiling thermally insulated to a value greater than R40.
Do not disassemble the unit for reconstruction. It may cause fire or electric shock.
Ceiling joist must be subjected to static load more than five times the weight of the product.
Install the fan at least 1.5m(5feet) above the floor, and the fan must be installed above a
counter or major appliances that serves as a barrier.
A statement to the effect that when the product is to no longer be used, it must not be left
in place but remove, to prevent it from possibly failing.
Do not install with a method which is not approved in the instructions.
Do not install this ventilating fan where interior room temperature may exceed 104°F (40°C)
This product must be properly grounded.
Do not use this fan with any solid-state speed control device. Solid state controls may cause
harmonic distortion which can cause motor humming noise.
Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and
the Occupation Safety and Health Act (OSHA).
Always disconnect the power source before working on or near the fan,motor or junction box.
Protect the supply wiring from sharp edges oil, grease, hot surfaces, chemicals or other objects.
Do not kink the supply wiring.
Not for use in cooking area. (Fig.A)
The special-purpose or dedicated parts, such as mounting
fixtures, must be used if such parts are provided.
For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
Floor
45°
45°
Cooking
equipment
Fig. A
(Cooking area)
Do not install above or
inside this area
Provide make up air for proper ventilation.
Do not install the unit where ducts are configured as shown in below.
Bend close to duct adaptor
Squeezed ductSuccessive bendingExcessive bending
Adaptor
When one switch is connected with two or more products in parallel, the unit may not function.
Therefore, parallel connection should not be allowed.
3
NOTICE

English
SUPPLIED ACCESSORIES
UNPACKING
Unpack and carefully remove the unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
11
1
Installation
instructions
Self-drilling
screw
Warranty
sheet
Part name Part nameAppearance Quantity
Grille
4
TM
Flex-Z Fast
bracket
(with 4
tapping screws
-ST4.2X20)
1
Appearance Quantity
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning this product on and off, the user is encouraged to try to correct the
interference by one of the following measures:
Warning: This equipment must be installed by qualified person in accordance with the provided installation
instructions; and all applicable codes and standards. Also, any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate this equipment.
DoC Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Customer Call Center: 1-866-292-7299
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Risk of Fire: Type IC-Inherently Protected.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect equipment into outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
DESCRIPTION
These products are listed by UL under UL file No. E78414.
These products use a sirocco fan driven by a DC motor powered by an integral transformer. The motor is
designed to have long operating life, high dynamic response, higher speed ranges with saving energy.
The grille covering the fan body is a spring-loaded, quick remove type. A damper for preventing air counter
flow is provided. The blower uses a high-capacity sirocco fan developed to reduce the noise level. The
lighting unit is an energy-saving LED lighting device that uses one 10W LED lamp and produces almost the
same illumination as a standard 40W incandescent lamp. Night light feature consumes around 0.1 to 0.4 W.
(FV-0511VQCL1 only)
This Panasonic ventilating fan model is equipped with a motion sensor and a humidity sensor that turn
on automatically when motion is detected, when humidity increases rapidly, or when humidity rises above
a 30% ~ 80% relative humidity set-point. It is user-adjustable to operate 0.5 ~ 60 minutes after the sensors
are no longer detected.
4

English
DIMENSIONS
Motion sensor location
Unit: inches (mm)
FV-1115VQL1
FV-1115VQL1
FV-1115VQL1
FV-0511VQL1 , FV-1115VQL1
FV-0511VQCL1
10 1/4 (260)
5 7/8 (151)
5 7/8 (148)
13 (330)
7 1/2 (190)
1 1/4 (30)
4 1/2 (114)
1 1/2 (37)
3 7/8 (100)
12 (304)
3 3/8
(86)
13 1/4 ~ 15 1/2 (336~394) 16 1/2 ~ 18 3/4 (419~480) 21 1/4 ~ 23 1/2 (540~597)
3 3/8
(86)
6 5/8 (169)
10 1/4 (261)
13 (330)
3 7/8
(100) 3 7/8 (100)
10 1/4 (260)
5 7/8 (151)
13 (330)
7 1/2 (190)
1 1/4 (30)
4 1/2 (114)
3 7/8 (100)
12 (304)
3 3/8
(86)
13 1/4 ~ 15 1/2 (336~394) 16 1/2 ~ 18 3/4 (419~480) 21 1/4 ~ 23 1/2 (540~597)
10 1/4 (261)
13 (330)
3 7/8
(100)
1 1/2 (37)
Part name
Grille
Blade
Junction box
Adaptor
PCB box
Part name
No. No.
Pick-A-Flow switch
Lighting unit
Fan body
Damper
5
6
7
8
9
1
4
2
3
Part name
Grille
Blade
Junction box
Adaptor
PCB box
Part name
No. No.
Pick-A-Flow switch
Lighting unit
Fan body
Damper
Selector
5
6
7
8
9
1
11
12
4
2
3
1
5
3
4
9
10
9
10
7
2
8
1 3
7
2
4 11
12
6
56
TM
Flex-Z Fast bracket
10
10 TM
Flex-Z Fast bracket
8
5

English
SELECTOR INDICATION (FV-0511VQCL1 only)
Humidity
preset selector
Selector indications
on blower unit
Timer
preset selector
FV-0511VQCL1
FV-0511VQL1 , FV-1115VQL1
WIRING DIAGRAM
Main control circuit
Humidity sensor
Fan body
Motion sensor
LED
DC
Motor
Junction box
AC120V
60Hz
(Power supply)
AC120V
60Hz
(Power supply)
Selector
White
Black
Live (Light)
Live (Fan)
Live (N.Light)*
Neutral
Neutral
Ｂlue
White
Black
Green
Main control circuit
Fan body
LED
DC
Motor
Junction box
AC120V
60Hz
(Power supply)
AC120V
60Hz
(Power supply)
White
Black
Live (Light)
Live (Fan)
Live (N.Light)*
Neutral
Neutral
Ｂlue
White
Black
Green
(Ground wire)
Main control
circuit
Main control
circuit
Factory setting : 20 minutes.
Position ” ” : For factory use
Factory setting is around 50%.
Timer preset selector positions
Timer
[min]
Humidity selector range from around 30% to 80%
0.5 1 2 3 5 10 20 30 60
TimerHumidity
setting
6
Night light
(Ground wire)
*

English
OPERATION (FV-0511VQCL1 only)
Motion sensor detectible
condition
1. The product will run when environment humidity rise rapidly but not reach to the humidity setting,
and stop after delay preset time.
2. Humidity setting selector is stepless change between 30 %RH~80 %RH.
3. The humidity detected by sensor may differ from the value on your hygrometer.
4. The product may turn on and off cause by the unstable environment humidity, you can improve
it by adjusting the Humidity setting selector.
Panasonic ventilating fan
responds to:
(1) Motion sensor detectible
condition.
(2) Humidity sensor detectible
condition.
90°
The delay time is determined
by timer preset switch.
The unit continues running for
an adjustable duration
of 0.5 to 60 minutes, after
motion is no longer detected.
The distance that motion
can be detected is limited
to 10 feet (3m).
The field of view of the
sensor is 90°.
Room temperature is
25°C (77°F).
10 feet
(3m)
sensor
FEATURE
All the WhisperCeiling ventilating fans come with Pick-A-Flow
speed options. The Pick-A-Flow switch on the face of all
WhisperCeiling ventilating fans allow the option to choose
50 – 80 – 110 CFM for the FV-0511VQL1 or 110 – 130 – 150 CFM
for the FV-1115VQL1.
These fans can run with constant air volume depending upon
the needs of the owner.
Pick-A-Flow Feature
Optimum Ventilation Performance:
Duct length, elbows and other factors increase static pressure which can hinder the performance of most
ventilation fans. This fan utilizes Smart Flow microchip technology that monitors the static pressure in the
system and speeds up or slows down the rpm of the fan depending upon the amount of resistance within
the ducts. This feature allows the fan to perform as rated and avoid potential installation issues.
The WhisperCeiling ventilating fans are built using DC motor technology. The DC motor is 30% - 70%
more energy efficient than the AC motor.
Outstanding Energy Savings:
Pick-A-Flow
switch Air volume (CFM) Factory setting
FV-0511VQL1
FV-1115VQL1
FV-0511VQCL1
50
110 80 130 110
50 80 110
80 CFM
150 130 CFM
80 CFM
Stop When motion is
detected, fan runs Remains running
until the delay time
has passed
Human
activity
Fan
activity
INSIDE
OUTSIDE
7

English
CAUTION
7. Refer to WIRING DIAGRAM.
Follow all the local electrical safety
codes as well as the National Electrical
Code (NEC). Using UL approved wire
nuts, connect house power wires to
ventilating fan wires. (Fig.5)
Mount junction box cover carefully
so that lead wires are not pinched.
INSTALLATION (NEW CONSTRUCTION)
1. Disconnect plug connector from receptacle (Fig.6)
and remove adaptor from fan body by removing the
machine screw (M4X8) before installation. (Fig.1)
IMPORTANT:
Remove the tape from damper and adaptor
before installation. As shown below:
The fan position between joists from 16" to 24"
on center can be adjusted flexibly.
2. Bend down 4 tabs for positioning, install the
Flex-Z Fast bracket to joists by drilling 2 tapping
screws which have been fixed on it. (Fig.2)
TM
TM
3. Adjust the length of Flex-Z Fast bracket as the
spacing between joists, and install to joists by
drilling the other 2 tapping screws which have
been fixed on it. (Fig.3)
4. Remove junction box cover and secure conduit
or stress relief to junction box knock-out hole.
(Fig.4)
TM
6. Install the adaptor to Flex-Z Fast bracket by
using 2 self-drilling screws. (Fig.4)
5. Install a circular duct and secure it with clamps,
or ties and seal it with mastic or approved foil tape.
A 4 or 6 inch circular duct is needed to connect to
relevant part of adaptor. (Fig.4)
Please wear gloves during the installation
work as follow.
CAUTION
Tape
Adaptor Damper
Fan body
Adaptor
Fig.1
Machine screw
(M4X8)
Fig.2
2 Tapping screws
(ST4.2X20)
Bend down
4 tabs
Joist
Fig.3
Joist
2 Tapping screws
(ST4.2X20)
2 Self-drilling screws
Knock-out
hole
Junction box
cover
Conduit
Circular duct
Mastic or
approved
foil tape
Fig.4
Fig.5
BLACK
WHITE
BLUE
GREEN
Wire nuts
Live
(Light)
(N.Light)*
Neutral
Junction box
L
N
120 VAC
LINE IN
Switch box
Conduit
Earth ground
Earth ground
Live (Fan)
Neutral
8
Live
* Night light.

English
INSTALLATION (NEW CONSTRUCTION) CONTINUED
Fig.7
Fig.9
Unit: inches (mm)
Grille
Ceiling
Gloves
Mounting spring
After finishing the ceiling job, fill gap between flange
and ceiling with caulk or other sealant to prevent air
leakage
8. Insert fan body and slide into adapter assy
with some strength, until the flange overlaps
the Flex-Z Fast bracket. Secure the fan
body to Flex-Z Fast bracket by using 2
self-drilling screws, plug connector to
receptacle and secure the fan body to adaptor
by using machine screw (M4X8). (Fig.6)
TM
TM
Secure machine screw (M4X8) to the
suitable hole and not touch the Flex-Z
Fast bracket. Please fix the screw
carefully to avoid screw slip teeth.
TM
13. Insert the other mounting spring into the slot as
shown and mount grille to fan body. (Fig.9)
12. Adjust Pick-A-Flow switch.(Refer to indication on
FEATURE.)
9. Finish ceiling work. Ceiling hole should be aligned
with the inside edge of the flange. (Fig.7)
CAUTIONCAUTION
10. Insert the grille mounting spring on the wiring
side into the slot and insert the plug connector
into the housing of the lighting unit. (Fig.8)
Before turn on the light, make sure the
connector at the correct position. If not,
the lighting can’t work.
The claw of connector must latch the rib
completely.
CAUTION
Mount grille carefully so that lead wire is not
pinched.
CAUTION
Machine
screw
(M4X8)
Fig.6
2 Self-drilling
screws
Plug connector
Receptacle
10 1/2(270)
10 1/2 (270)
Ceiling
Fig.8
Motion sensor
(FV-0511VQCL1 only)
Mounting spring
Lightingunit
Ceiling
Clasp
9
11. Insert the motion sensor on the grille and dress
the wire as shown. (Fig. 8)

English
CAUTION
INSTALLATION (RETROFIT)
Ceiling Flange
Machine screw (M4X8)
2 Self-drilling screws (Fix the
TM
flange and Flex-Z Fast
through the ceiling) bracket
1. Remove the existing fan and cut ceiling opening.
Secure the Flex-Z Fast bracket to joists
by drilling 4 tapping screws (ST4.2x20) which
have been fixed on it. Existing ductwork and
wiring left in place. (Fig.10)
2. Follow the step 1 , 4 , 5 , 7 on INSTALLATION
(NEW CONSTRUCTION). (Before connect the
circular duct to the adaptor, should pull down
the circular duct from the ceiling)
Disconnect power source before working
on unit.
5. Follow the step 10 to 13 on INSTALLATION
(NEW CONSTRUCTION)
TM
TM
3. Install the adaptor to Flex-Z Fast bracket by
using 2 self-drilling screws. (Fig.11)
4. Secure the fan body to Flex-Z Fast bracket by
using 2 self-drilling screws, plug connector to
receptacle and secure the fan body to adaptor
by using machine screw (M4X8). (Fig.12)
Secure machine screw (M4X8) to the suitable
hole and not touch the Flex-Z Fast bracket.
Please fix the screw carefully to avoid screw
slip teeth.
TM
Fig.12
CAUTION
WARNING
WARNING
Disconnect power source before working on unit.
Routine maintenance must be done every year.
Please wear gloves during the cleaning work.
Never use gasoline, benzene, thinner or any other
such chemicals for cleaning the ventilating fan.
Do not immerse motor in water when cleaning.
Do not soak resin parts in water over 140°F (60°C).
Fig.13
Gloves
MAINTENANCE (CLEANING)
10 7/8 (275)
10 7/8 (275)
Circular ductConduit Joist
4Tapping
(ST4.2x20)
Unit: inches (mm)
Fig.10
Ceiling (already existed)
screws
Mastic or
approved
foil tape
2 Self-drilling screws
Ceiling
Joist
Knock-out
hole
Junction box
cover
Conduit Circular duct
Fig.11
Joist
1. Clean grille. (Don’t put into hot water. Use non-abrasive
kitchen detergent, wipe dry with clean cloth) (Fig.13)
2. The grille should be dry after cleaning.
3. Remove dust and dirt from fan body using a vacuum cleaner. (Fig.14)
Do not use cleaning sprays, solvents, or water on
or near the sensors.
Fig.14
Ceiling
Vacuum
cleaner
TM
10

English 11
Make sure the temperature of LED unit has cooled
down before maintenance
(cleaning) or replacement of lamp.
WARNING
MAINTENANCE (CLEANING) CONTINUED
Gloves
Ceiling
5. Reinstall grille.
4. Using a cloth dampened with kitchen detergent, remove
any dirt from fan body. Wipe dry with clean cloth. (Fig.15)
Fig.15
Fig.16
lnsulation
4 inches or 6 inches roof jack, wall cap,
or soffit vent with backdraft damper
Mechanically connect duct to termination
and seal with mastic or approved foil
faced tape
2-3 ft straight run before elbow
Short piece of flexible duct helps
alignment and absorbs sound.
Clamps plus mastic or approved
foil faced tape at all flex joints Foil tape tightly covers all metal
duct joints (glue PVC joints)
Properly insulate the area around the fan to
minimize building heat loss and gain. (Fig.16)
Loose fill or batt insulation can be placed
directly over the fan housing in the attic.
Our fans does not create excessive heat that
is a common problem with recessed light
fixtures or some competitor’s fan/light
combination. Our efficient, cool-running
motors do not create enough ambient heat
to be subjected to these limitations.
The ducting from this fan to the outside of
the building has a strong effect on the air flow,
noise and energy use of the fan. Use the shortest,
straightest duct routing possible for best performance, and avoid installing the fan with smaller
ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold
growth. Fans installed with existing ducts may not achieve their rated air flow.
ln attic installation,
caulk box to drywall
PRACTICAL GUIDE TO INSTALLATION
Model No. Air
direction
Exhaust 4 or 6
Exhaust
Voltage
(V) Frequency (Hz) Noise (sones) Speed (rpm) Power (W) Weight Ib.(kg)
Duct
diameter
(inches)
Air volume
at 0.1"WG
(CFM)
FV-0511VQL1
FV-1115VQL1 110 <0.3
<0.3
0.5
<0.3
<0.3
0.4 7.8
4.0
10.4
6.1
11.0
13.1
679
722
740
768
867
1016110
130
660120
60120
150
50
80 9.9(4.5)
10.1(4.6)
Exhaust FV-0511VQCL1
50 <0.3
<0.3
0.4
4.0
6.1
11.0
768
867
1016
80
4 or 660120 110 10.1(4.6)
HVI Certified performance based on HVI Procedures 915, 916, and 920.
SPECIFICATIONS

Panasonic Corporation 2017
Warning Concerning Removal of Covers. The unit should be serviced by qualified technicians only.
Your product is designed and manufactured to ensure a minimum of maintenance. Should your unit
require service or parts, call Panasonic Call Center at 1-866-292-7299 (USA) or 1-800-669-5165 (Canada).
Printed in Mexico
P0717-0 11QCL1420B
PRODUCT SERVICE
Panasonic Corporation of North America Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
www.panasonic.ca
Two Riverfront Plaza, Newark, NJ 07102
www.panasonic.com