Panasonic Panaboard UB-5310 User manual

Electronic Board
Installation Manual
(for qualified service personnel)
Model No. UB-5310
English . . . . . . . . . . . . . . . . . 1–20
Français . . . . . . . . . . . . . . . . 21–40
Deutsch . . . . . . . . . . . . . . . . 41–60
Español . . . . . . . . . . . . . . . . 61–80
Italiano . . . . . . . . . . . . . . . . 81–100
Nederlands. . . . . . . . . . . . . 101–120
Svenska . . . . . . . . . . . . . . . 121–140
中 文 . . . . . . . . . . . . . . . . . 141–160
Русский . . . . . . . . . . . . . . . 161–180
Stand kit is optional.
[Stand (option)] [Wall-mounting]
English Français Deutsch Español Italiano Nederlands Svenska 中 文 Русский
• Please ask your dealer regarding assembly of the electronic board and instruction for wall-mounting.
Before installing this set, please read this manual completely.

2
Before installing this set, please read this manual completely.
CLASS 1 LED PRODUCT
WARNING
DO NOT INSTALL THIS OPTION EXCEPT
QUALIFIED SERVICE PERSONNEL.
CAUTION
SAFETY CHECK MUST BE DONE BY
QUALIFIED SERVICE PERSONNEL AFTER
INSTALLING THIS OPTION.
Table of Contents
page
Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . . . 3
●Accessories for assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electronic Board Operations Check. . . . . . . . . . . . . . . . . . . . 11
Repacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assembling the Optional Stand (UE-608005) . . . . . . . . . . . . 13
●Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
●Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wall-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
●Wall-mounting fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
●Wall-mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
●Attaching the wall-mounting fixtures. . . . . . . . . . . . . . . . . . . . . . . . . 19

3
English
Assembling the Electronic Board
■Accessories for assembling
The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts
are included in the package before proceeding.
* These names [Wall-mounting fixture (upper)/Wall-mounting fixture (lower)] are used for installing on the wall.
Part Name Illustration/Quantity Remarks
Board attachment
(upper)
[*Wall-mounting
fixture (upper)]
Board attachment
(lower)
[*Wall-mounting
fixture (lower)]
Cover (upper)
Cover (lower)
Screws and spacers
For screen
For printer
and screen For cover For screen For screen
Screen
Page 6, Step 11
Printer
Page 8, Step 17
Cover (lower)
Page 10, Step 22
Paper holder
Paper holder
Wrench
Power cord
Wall-mounting
template
Use the Wall-mounting
template1 and 2 by
pasting them together.
(Long) (Short)
A
B
1
1
1
1
661 6
1
1
1
Q’ty
6
1
1

Assembling the Electronic Board
4
■Assembly
1Assemble the optional stand or wall-mounting fixture.
■If you are using a stand, refer to page 13.
■If you are using a wall-mounting fixture, refer to page 17.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
Caution
• When removing the screen unit, grasp the side cover on either side of screen.
Do not grasp the screen film surface, as this may scratch it.
• The shipping box, cushioning material, and other packing material will be necessary if you ever need to
repackage the electronic board, so do not throw them away.
Board attachment (lower)
Board attachment (upper)
Copy paper roll
Power cord
Cover (upper)
Cover (lower)
Markers
Screen unit
Printer unit
Eraser
Paper holder ·
AB
Manuals, CD-ROM
Joint
Screws and spacers

Assembling the Electronic Board
5
English
3Collapse the carton box.
Remove the tape and the staples on
the unopened side of the carton box,
then collapse the box.
4Remove the protective plastic bags.
Remove the protective plastic bag
from the screen unit and printer unit.
Set those units on the top of collapsed
shipping box and remove the
cushions.
Caution
• Touch the screen film surface gently to avoid
any damage.
5Attach the screen unit to the
optional stand or wall mounting
fixture.
■If you are using the stand, refer to
page 13.
■If you are using the wall mounting
fixture, refer to page 17.
6Hang the screen unit to the board
attachment (upper).
Hold the side covers of the screen unit
and hang two hooks of the screen unit
on the left side of the board
attachment (upper).
Shift the screen unit to the left until it
stops. Confirm the left hook is inserted
into the groove of the board
attachment (upper).
• When hanging the screen unit, set the board
attachment frame at the lowest level.
• Be careful not to catch the screen film on the
board attachment frame.
7Remove the shipping screws.
Remove the lower and upper shipping
screws on the folded screen.
Caution
• Remove the lower shipping screw first.
Carton
To p
Bottom
Remove the tape
and the staples.
Protective
plastic bag
Screen unit
Cushions
Cushions
Cover (left) Board attachment
(upper)
Cover (right)
Board
attachment
Frame

Assembling the Electronic Board
6
8Extend the screen unit.
Open the center and right panels of
the screen unit as shown below and
remove the cushion.
Caution
• Touch the screen film surface gently when
opening the screen unit.
9Unlock the hook.
Unlock the hook connected to the
center and right panels. Extend the
screen unit and remove the cushion
behind the screen.
Caution
• Touch the screen film surface gently when
opening the screen unit.
10 Extend the screen unit.
Hang the right hook of the screen unit
on the board attachment (upper).
Caution
• Touch the screen film surface gently when
opening the screen unit.
11 Fix the screen unit.
Fix the left, center and right panels
with the screws and spacers supplied.
To tighten the screws, use the
supplied wrench.
Cushion
Lift the right
panel slightly
and extend it.
Hook
Cushion
Right hook
Spacers
Screws (short)
Screws
(long)
Washer
Washer

Assembling the Electronic Board
7
English
■Adjusting the level of the screen
unit (Step 12–15: only for use of
the optional stand)
At the lowest level of the board attachment frame,
the printer cannot be installed. Raise the level of
the screen unit as follows.
• Please lock the casters when you adjustment the
screen height. Refer to Operating Instructions
page 5.
12 Loosen the height adjustment
handles on the board attachment
frame.
13 Hang the step frame on the center
of the reinforce pipe.
Hold the center of the board attachment
(lower) of the board attachment frame from
the back of the screen unit and lift the board
attachment frame by stepping on the step
frame to lift the board attachment frame
smoothly.
When lifting the board attachment frame, be
sure to hold the handle in the center of the
frame.
14 Hang the screen in the desired slots
of the slide plates and tighten the
handles.
Caution
The screen can be adjusted at 4 levels.
• The lowest level of the board attachment frame
is designed for the installation of the screen, so
the printer cannot be attached at that level. Use
the electronic board at upper 3 levels.
• Make sure to tighten the height adjustment
handles firmly after adjusting the level of the
screen.
• Confirm both of the screws are hung in the same
height slots.
• Store the step frame by hanging it on the board
attachment (upper).
Height
adjustment
handles
Height
adjustment
handles
Board
attachment
(lower)
Reinforce pipe
Step frame
Slot for installing
the screen
(The printer cannot
be attached at this
position.)
Slots for
height
adjustment
Step frame

Assembling the Electronic Board
8
15 After hanging the screen, fix the
stopper screw (left side only).
This prevents the user from adjusting
the screen height at the lowest level by
mistake.
16 Attach the printer unit.
Hang the hooks of the printer unit on
the square holes of the board
attachment (lower).
Caution
• When attaching the printer unit, make sure the
cable is not caught between the metallic frame
and the printer unit.
17 Tighten the screws for the printer
unit.
Use four screws for the optional stand
and two screws for the wall mounting.
■Optional stand
■Wall-mounting
Stopper screw
[Screw(short)
See page 13.]
Board attachment
(lower)
Printer unit

Assembling the Electronic Board
9
English
18 Connect the cables (2) to the screen
panel connectors.
19 Remove the folding support screw
on the front side of the screen unit,
then store the folding support on
the back side.
20 Attach the cover (upper).
Hook the cover with the projections on
both sides, then cover the top of the
board attachment (upper).
21 Store the shipping screws for fixing
the screen panels, the screw for the
folding frame and the wrench in the
tool box on the top of the printer
unit.
Folding support screw
Folding support
Board attachment (upper)
Cover (upper)
Tool box
Shipping screws
Wrench
Folding support screw

Assembling the Electronic Board
10
22 Attach the cover (lower).
(1) Push the cover in the direction of
the arrow until it clicks.
(2) Fix the cover with the wing bolt.
23 Attach the power cord.
Securely fit the supplied power cord
into the AC inlet on the printer unit.
24 Attach the paper holders.
Attach the paper holders to the printer
section in numerical order of the
arrows (1), (2), (3) and (4).
25 Attach the rear cover. (only for use
of the optional stand)
• After peeling off the cover sheets of the
adhesive tapes, attach the rear cover to the
board attachments (upper/lower) while
matching the top edges of them. Then install
the rivets.
• The rear cover and rivets are supplied with
the optional stand.
26 Wipe the screen film surface.
Soak a soft cloth with water, wring
well, and wipe the screen film surface.
Caution
• Do not wipe the screen film surface with paint
thinner, benzene, or cleaners that contain
abrasives. Doing so may cause discoloration.
• Do not wipe the screen film surface with a dry
cloth. Doing so may create static electricity.
27 Check the operations.
Refer to “Electronic Board Operations
Check” on page 11.
AC inlet
Power cord
Paper holder
Install first.
A
Hole for A
B
Hole for B
Hole for A
Paper holder
Install second on top of first.
B
Adhesive
tape
Rivets

11
English
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it
functions properly.
Step
Points to Check
Symptom Solutions
1Turn on the power switch. “ ” flashes after “ ” lights up. (Normal operation)
(If not) Check power cord and
cables.
(See step 23 on page 10
and step 18 on page 9.)
2Open the printer door and load the
copy paper, then close the printer door.
• loading the copy paper procedure
(refer to the Operating Instructions
page 10)
“ ” lights up after the copy paper
is fed and automatically cut.
(Normal operation)
(If not) Check the condition of
printer door or copy
paper roll.
3Press . Screen is fed. (Normal operation)
The screen film surface is not fed
smoothly.
Contact the store or
dealer from which the
unit was purchased.
There are strange noises.
4Use the accessory marker to draw
a large filling the entire
copyable area of the screen film
surface.
• Copying area (refer to the
Operating Instructions page 7)
Press twice.
Press .
“ ” lights up and three copies
are made.
(Normal operation)
Three copies are not made. Contact the store or
dealer from which the
unit was purchased.
The entire readable area is not
printed.
There are strange noises or
paper jams during the copying
process.
5Press to move the screen film
surface.
Write letters, etc. with the marker.
Press once.
Press .
The Contrast indicator light is
turned on and copy is made.
(Normal operation)
The Contrast indicator light is
not turned on.
Contact the store or
dealer from which the
unit was purchased.
The image is not copied properly.
There are strange markings on
the copy sheet (e.g., stripes or
lines).
6Press once. The Contrast indicator light is
not turned off.
Contact the store or
dealer from which the
unit was purchased.
7Press . Two screens are not copied
properly.
Contact the store or
dealer from which the
unit was purchased.

12
Repacking
Perform Assembly Steps 2 through 24 in reverse to repack the electronic board and accessories. Use the joints to
fasten the shipping box to the lower box.
Caution
• When handling the screen unit, grasp the side cover on either side of screen.
Do not grasp the screen film surface, as this may scratch it.
Board attachment (lower)
Board attachment (upper)
Copy paper roll
Power cord
Cover (upper)
Cover (lower)
Markers
Screen unit
Manuals, CD-ROM
Printer unit
Eraser
Paper holder ·
AB
Joint
Screws and spacers

13
English
Assembling the Optional Stand (UE-608005)
■Accessories
The package box for the optional stand includes the parts noted below; please confirm that all parts are present
before beginning installation
.
The accessory Wrench is required when disassembling the electronic board; please store it carefully for future use.
*1A screw (short) is used for the stopper screw of step 15 on page 8.
●Before assembly, be sure to lock the casters.
No. Part name Illustration Q’ty No. Part name Illustration Q’ty
Base pipe 2 Screw 2
Reinforce pipe 1
Height
adjustment
handle
4
Extension pipe
S1Nut 4
Extension pipe
L
(not use)
1Cap 2
Side pipe 2 Step frame 1
Slide plate
(Left) 1
Fall-preven-
tion extension
leg
4
Slide plate
(Right) 1Wrench (for stand) 1
Fixing plate 2 Rear cover 1
Screw (long) 12 Rivet 6
Screw (short) 11*1Washer 8
Locking the casters
(Push this side)
Releasing the lock

Assembling the Optional Stand (UE-608005)
14
■Assembly
1Assembling the stand
■Assembling the fall-prevention extension legs
The fall-prevention extension legs are effective in increasing the safety of the electronic
board.
Caution
• Install and always set the fall-prevention legs when using the stand.
• When tightening the screws , hold the nut with pliers.
■Assembling the stand
• Assemble the side pipes with the slide sheets facing inside.
Fall-prevention extension legs • Caster locks are attached
to the back side.
Slide sheet
Side pipe
Base pipe
Extension pipe S
Base pipe
Reinforce pipe
Slide sheet

Assembling the Optional Stand (UE-608005)
15
English
2Assembling the board attachment frame
• The board attachments (upper and lower) are supplied with the electronic board.
• Place the board attachments and the slide plates with their stamps facing up and assemble them matching
their same stamps.
3Attach the board attachment frame to the stand.
Details of the procedures are as follows.
Step A Attach the fixing plate to the board attachment frame.
Stamp “UL”
Stamp “LL”
Stamp “UR”
Stamp “LR”
Board attachment (upper)
Slide plate
(right)
Board attachment (lower)
Slide plate
(left)
Step E
Step D
Step A
Step B
Step C
Step D
Step C
Step A
Slide
plate
Fixing
plate
Cap
Height
adjustment
handle
Screw
Height
adjustment
handle
Fixing plate
Side pipe
Side pipe
The caster locks
are attached to
the back side.
The wider side is front.

Assembling the Optional Stand (UE-608005)
16
Step B Place the screws with the board attachment frame in the grooves of the side
pipes.
• When the side pipe leans to the inside, stand it up and attach the board attachment frame.
Step C Insert the screws into the side pipes from the inside.
Step D Install and secure the height adjustment handles .
Step E Fix the caps to the side pipes.
4Assemble and install the electronic board.
Refer to pages 4 to 10.
5Insert and keep the wrench in the holder on the cover lower.
Board attachment frame
Side pipe
Side pipe
Fixing plate
Screw
Wrench (for stand)
Cover (lower)

17
English
Wall-mounting
■Wall-mounting fixture
The wall-mounting fixture includes the board attachment (upper and lower) supplied with the unit.
Before attempting installation of this wall-mounting fixture, we strongly recommend consulting with the building
manager, engineer, or architect. The installer needs to know the type of construction used for the wall intended for
this installation and the location of wall studs. Selection of hardware is critical for safe wall-mounting, and
depends on the nature of wall construction. Installation should not occur until this consultation takes place.
Caution
• Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall-mounting
fixture bolts to metal laths or wire laths can cause heat, smoke or a fire.
I. Tools required:
A minimum of four (4) pieces of appropriate wall-support hardware (molley, toggle, etc.)
NOTE: THIS HARDWARE MUST BE LOCALLY PROCURED, IT IS NOT INCLUDED IN THE PRODUCT.
Drill (and drill bit of correct size) for hardware installation
Screw driver (Both phillips (+) and slotted (–) will be required.)
Tape measure
Tape or thumb-tacks (2 pcs)
Bubble type level
II. Pre-requisites
1. Before installation, make sure that the wall intended for installation is capable of supporting flush-
mounted.
80 kgf (176 lbs.).
2. The position of the intended installation is of adequate size for the selected Panaboard.
1,440 mm (H) ×1,372 mm (W) [56.7"(H) ×54.0"(W)].
3. An outlet is within 3 m (118.1"), and not located behind the Panaboard.

Wall-mounting
18
■Wall-mounting procedure
1Confirm that the wall is strong enough to support the weight of the electronic board.
Caution
The wall must be capable of supporting at least
784N [80 kgf (176 lbs.)].
21) Assemble the wall-mounting template by taping the Wall-mounting template 1
(TOP) to Wall-mounting template 2 (BOTTOM).
2) Tape the wall-mounting template on the wall.
• When taping the template on the wall, make sure it is level.
31) Drill holes in the wall at the 4 spots indicated by and , or and for the
wall-mounting fixtures.
• Holes on the wall-mounting fixture are 7 mm in diameter.
2) After removing the wall-mounting template, attach the wall-mounting fixtures
with the appropriate wall-mounting hardware.
• Refer to the section “Attaching the wall-mounting fixtures” (page 19) for drilling in the wall and attaching the
mounting fixtures.
• Refer to steps 2 to 24 on pages 4 to 10 for attaching the printer and the screen.
ACBC
517 mm
AB
C
AB
C
AB
C
AB
C
Wall-mounting
template
Wall-mounting hardware
Board attachment (upper)
(Wall-mounting fixture upper)
Board attachment (lower)
(Wall-mounting fixture lower)
Wall-mounting hardware
940 mm
Remove the
edge cover.
Remove the
edge cover.
900mm
812mm
Center of the electronic board

Wall-mounting
19
English
■Attaching the wall-mounting fixtures
The electronic board must be mounted with the method most suited to the material of the wall.
Three methods are presented here.
(Other options may be available in your area.)
●Attaching to metal or concrete walls
Stud plugs (sold in stores) are needed.
●Attaching to plasterboard walls
Split-wing toggles (sold in stores) are needed.
Drill four holes in the wall.
For the correct hole size, refer
to the instructions for the
particular stud plugs used.
Insert each bolt through a hole
in the wall-mounting fixture and
tighten until the wall-mounting
fixture is securely fixed to the
wall.
Drill bit
Metal or concrete
wall
Stud plug
Insert a stud plug in each hole.
Wall-mounting
fixture
Bolt
Insert each bolt through a hole
in the wall-mounting fixture and
into the hole in the wall beneath
so that the arms of the split-
wing toggle are horizontal. For
the correct hole size, refer to the
instructions for the particular
split-wing toggles used.
After the arms expand, pull the
wall-mounting fixture out until
the arms of the split-wing toggle
grip firmly into the wall.
Tighten each bolt until the wall-
mounting fixture is securely
fixed to the wall.
Plasterboard
Split-wing toggle
Wall-mounting
fixture
Bolt
Arms
Arms

Wall-mounting
20
●Attaching to wooden walls
Use wood screws (sold in stores).
For the correct hole size, refer
to the instructions for the
particular wood screws used.
Wall-mounting fixture
Wood screw
Wooden wall