Panasonic EY3610 User manual

© Panasonic Eco Solutions Power Tools Co., Ltd.
2012. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PTD1208E01CE
Variable Speed Cordless Sealing Gun
Model No. EY3610
Europe
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Trial Operation (After Checking Troubleshooting
Guide) ---------------------------------------------------------------- 5
5 Disassembly and Assembly Instructions ---------------- 6
6 Wiring Connection Diagram ---------------------------------13
7 Schematic Diagram ---------------------------------------------13
8 Exploded View and Replacement Parts List -----------14

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide

4

5
4 Trial Operation (After Checking Troubleshooting Guide)
4.1. Assembly
• Confirm if there is NO gap between Housing A and B by pinching the lead wires.
• There is no dust or deformation on battery terminals.
4.2. Operation
• Confirm if SWITCH turns ON and OFF normally.
• Confirm the smooth changing of HIGH and LOW handle and its changing mode.
• Confirm if caulking pressure is appropriate.
Place end of the rack guide on floor and turn on the switch leaning your body weight onto the unit instead of using sealing.
Check if the rack guide extends properly.
• Confirm if operation is normal attaching the sausage and cartridge attachment.
• There should be no abnormal sound of gears chafing, metallic sound and no abnormal vibration.
• There should be no metallic sound and abnormal sound when shaking up-down and right-left.
4.3. Adjustment of remaining amount scale
1. Turn on and extend the rack guide till the end.
2. Furthermore pull it by hand in the direction of arrow until it clicks.
3. Keep pushing the switch again until white part shows approx.1mm after red part appears.
4. Push the rack guide all the way back inside by hand.

6
5 Disassembly and Assembly Instructions
5.1. Remove the cartridge holder from the main unit.
5.2. Pull up the rack guide and remove 3 tapping screws.

7
5.3. Pull the rack guide out forward.
5.4. Remove a connector cap.

8
5.5. Remove housing B.
5.6. Remove the module.

9
5.7. Remove the micro switch.
5.8. Remove 2 screws of the driving block.

10
5.9. Release the spring for switch handle from the housing boss with radio
pliers.
* Spring for switch handle is strong. Be careful to remove it.
5.10. Take the driving block parts out from housing A.

11
5.11. Remove the motor lead wires.
NOTE:
- Hold the terminal of lead wire with tweezers and touch the soldering iron tip to remove the lead wire.
- type: Insulating type of soldering iron with less than 80W
- procedure: Within 3 seconds with 400°C or less.
- solder: Lead free type (Sn-3Ag-0.5Cu)
5.12. How to remove and install the a spring of the rack guide.

12
5.13. Caution for assembly

13
6 Wiring Connection Diagram
7 Schematic Diagram

Model No. : EY3610 Exploded View
8 Exploded View and Replacement Parts List
14

Model No. : EY3610 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 WEY3610K3078 HOUSING AB SET 1
2 WEY3610K3657 CARTRIDGE CAP 1
3 WEY3610S3717 CARTRIDGE HOLDER 1
4 WEY3610K6118 TAPPING SCREW 11 TP4X14L
5 WEY3610K0527 HOUSING CAP 1
6 WEY2610L0207 WASHER 6
7 WEY3610L0277 CONNECTOR CAP 1
8 WEY3641K0488 ATTACHMENT FOR SAUSAGE 1
9 WEY3610L6767 PLUS SHAVEN HEND SCREW 1 M8X20 (5PCS/PK)
10 WEY3610L4897 RACK GUDE BLOOK 1
11 WEY3610L0197 ROOKER ARM SPPRNG 1
12 WEY3610L4037 DRIVING BLOOK 1
13 WEY3610K2007 SWITCH BLOOK 1
14 WEY3610L9357 TAPPING SCREW 3 TP3X12 (5PCS/PK)
15 WEY3610K6308 TAPPING SCREW 10 TP3X14L (5PCS/PK)
16 WEY3610L9257 TAPPING SCREW 2 TP2X10L (5PCS/PK)
17 WEY3610L3717 ATTACHMENT FOR CARTRIDGES 1
- WEY001T8907 GREAESE(ALBANIA) 1
- WEY3610K8008 INDIVIDUAL BOX 1
- WEY3610K8108 OPERATING INSTRUCTIONS 1
15